VTC-BHOC6R4F 2.1MP 3G-SDI IP67 Vandal Resistant WDR True Day/Night Bullet Camera with 3.6mm Lens & 30 IR LEDs VITEK FEATURES: • 1/3” 2.1 MegaPixel Progressive Scan CMOS sensor w/ NVP2420 DSP • 2.1 MegaPixel With full 1080p 3G-SDI (SMPTE 424M) @ 60fps / 30fps HD-SDI (SMPTE 292M) @ 30fps Output • 30 850nm Dynamic Intensity IR LEDs with 115’ Range • MegaPixel IR Corrected 3.
WARNINGS The camera needs periodic inspection. • Contact an authorized technician for inspection. Stop using camera if there is a malfunction. • Avoid installing camera in high heat areas, risk of fire may occur. Do not install the camera on a surface that can not support it. • Unless the surface is suitable, injury or other hazards may occur. Do not disassemble the camera. • It may result in fire, electric shock or other hazards. Do not hold plug with wet hands. • It could cause an electric shock.
PRECAUTIONS Ø Do not install the camera in extreme temperature conditions. • Only use the camera under conditions where temperatures are between -14˚F and +122˚F. Be especially careful to provide ventilation when operating under high temperatures. Ø Do not drop the camera or subject it to physical shocks. • It may cause malfunctions to occur. Ø Never point camera into a strong light source, such as the sun or bright spotlight. • It can damage the CMOS Sensor. Ø Do not expose the camera to radioactivity.
FEATURES • 1/3” 2.0 Mega-Pixel Panasonic Progressive Scan Sensor • Resolution: 1920 x 1080 (30P/25P, 60P/50P, 60i/50i) • HD-SDI / SMPTE 292M (30P/25P HD-SDI), SMPTE 424M (60P/50P 3G SDI) Video Output • HD over Coaxial Cable • Uncompressed HD Digital Video • WDR • True Day/Night by ICR • Smart 3DNR, 2DNR / Smart IR • RS-485 (Pelco®-D) Remote Control, Coaxial Cable Comm.
Setup Menu (OSD) SETUP MENU (OSD) [How to operate OSD joy stick] OSD menu is controlled by OSD joystick in OSD Board or OSD Cable -▲ (UP), ▼ (DOWN), ◀ (LEFT), ▶ (RIGHT), ● (SET / ENTER) [Menu Tree] 07 6
MENU TREE [Menu Tree] 7
MENU Tree] TREE [Menu 8
MENU TREE [Menu Tree] 9
MAIN OSD MENU Main OSD Menu MAIN MENU LENS DEFAULT DC Set SHUTTER, AGC, SENS-UP, BRIGHTNESS, D-WDR &, DEFOG EXPOSURE A BACK LIGHT Select WDR, BLC, HSBLC or OFF WHITE BAL ATW DAY&NIGHT AUTO NR DESCRIPTION Select Lens type according to mounted or built-in lens * ATW(Auto Tracking White Balance) * AWC -> SET : White Balance is fixed at the value when *(enter) is pressed and keeps the value * INDOOR : White Balance is fixed at about 3100K * OUTDOOR : White Balance is fixed at about 5100K * Manual
1. LENS 1. LENS Select Lens type, DC, MANUAL or P-IRIS. DC Lens: * MODE: Set INDOOR or OUTDOOR 2. EXPOSURE 2. EXPOSURE EXPOSURE DEFAULT SHUTTER AUTO DESCRIPTION Set Shutter Speed, 1/60(1/50), FLK, 1/240 ~ 1/50000 or x2 ~ x30 * If camera is equipped with auto iris lens, recommended to set to AUTO. * In the region NTSC but 50Hz power, set to FLK (Flickerless). In the FLK mode, sensitivity will be lowered under low light.
DEFOG OFF dark area. * This is to enhance visibility in foggy environments but the performance is limited. 3. BACKLIGHT 3. BACKLIGHT Select Backlight mode, WDR, BLC or HSBLC 3-1. WDR Set WDR level, LOW, MIDDLE or HIGH Note) WDR mode works only with HD-SDI output and not the CVBS (composite out) 3-2. BLC * BLC: This function is used to brighten an image in the foreground with a highly bright area behind it such as sunlight, limiting the affect of a silhouette.
BLC OFF BLC ON 3-3. HSBLC This function is used to black out highlighted (bright) areas, in order to enable a clear visual image of objects, such as the license plates of an oncoming vehicle or other objects that may be obstructed by headlamps. HSBLC SELECT DEFAULT AREA1 DISPLAY ON LEVEL 45 MODE ALL DAY BLACK MASK ON DEFAULT DESCRIPTION * Select area to adjust AREA 1~4. * Choose ON then push ● button to enter into selected area.
HSBLC OFF HSBLC ON 4. WHITE BALANCE 4.
5. DAY & NIGHT 5. DAY & NIGHT DAY & NIGHT DEFAULT DAY & NIGHT AUTO DESCRIPTION * AUTO : Camera switches DAY from/to NIGHT automatically according to the amount of light through the lens. * COLOR : Camera stays color regardless of light level * B/W: Camera stays black & white regardless of light level. * EXT : DAY or NIGHT is decided by light sensor(CDS sensor) use this if camera has built in IR’s 5-1.
5-2. B/W B/W 5-2. B/W BURST B/W IRBURST SMART IR SMART 5-3. EXT EXT 5-3. EXT BURST EXT IRBURST SMART IR SMART DEFAULT DEFAULT OFF OFF DEFAULT DEFAULT OFF OFF DESCRIPTION * Set BURST ON DESCRIPTION or OFF ** Set IR SMART ON or OFF Set BURST ON or OFF * Set IR SMART ON or OFF DESCRIPTION * Set BURST ON DESCRIPTION or OFF ** Set IR SMART ON or OFF Set BURST ON or OFF * Set IR SMART ON or OFF 6. NR 6. NR 6. NR 2D & 3D is a powerful noise reduction technology at low light.
6-1. 3DNR (ON) 3DNR DEFAULT SMART NR ON LEVEL 80 START. AGC 0 END. AGC 0 DESCRIPTION * Camera is watching for any motions. * When no motion is detect: 3 DNR is working with maximum noise reduction automatically. This will save HDD space on the DVR * When motion is detected: 3 DNR deactivates slow motion capture for moving object. * Set strength of 2D & 3 DNR. * Higher value, higher noise reduction.
7. SPECIAL SPECIAL CAM TITLE DEFAULT OFF D-EFFCT MOTION OFF PRIVACY OFF LANGUAGE ENG DEFECT RS485 DESCRIPTION * If set to ON, camera title is displayed. * Can set FREEZE, MIRROR, D-ZOOM, SMART D-ZOOM, NEG.IMAGE & DIS. * Programmable up to 4 areas. If motion is detected, mosaic effect appears. * Programmable up to 8 masked areas. * Support 16 languages, ENG / JPN / CHI1 / CH2 / KOR / GER / FRA / ITA / SPA / POL / RUS / POR / NED / TUR / HEB / ARB * To change the language, push ● (SET/ENTER).
7-1. CAM TITLE * * * * * * Input max.15 characters or symbols by using▲ (up)/▼ (down)/◀ (left)/▶ (right) buttons. Press ● to select and the selected character/symbol will be displayed on the input line → ←: move CAM TITLE input position CLR: remove all inputted characters and symbols POS: move and set CAM TITLE display position END: finish and return to menu 7-2.
D-ZOOM OFF SMART D-ZOOM NEG.IMAGE OFF DIS * Available max. 62x digital zoom. * PAN/TILT : set zoom position by moving UP / DOWN / LEFT / RIGHT. * Usable at 30/25P resolution. Cannot synchronize with SMART D-ZOOM but usable either D-ZOOM When motion is detected camera will digitally zoom in * If set to ON, shows negative image * Digital Image Stabilizer. Available at A-30/25P set up (will lose part of image) 7-2. �D-ZOOM D-ZOOM DEFAULT D-ZOOM X2.
7-2. �SMART D-ZOOM When motion is detected Smart D-Zoom will zoom into defined area.
7-3. MOTION MOTION DEFAULT SELECT AREA 1 DISPLAY ON SENSITIVITY 50 MOTION VIEW ON DEFAULT DESCRIPTION * Select area to be detected. Selectable up to 4 areas. * Able to position area and resize motion area * Set sensitivity value. Lower value is more sensitive. * ON : Enable mosaic display for the selected area * Return to DEFAULT 7-4.
Up to 8 privacy zones. PRIVACY SELECT DEFAULT DISPLAY COLOR TRANS DEFAULT DESCRIPTION * Select the area to mask. select area 1~ 8 * Select display type, OFF, INV, COLOR or MOSAIC set size and position to be masked for the selected area * Select color for masking, If color is selected in Display each area is able to have a different color * Able to set the transparence of selected color * Return to DEFAULT 7-5.
STAICE DPC DEFAULT STATIC DPC ON STATIC DPC “ON” START LEVEL 25 SENS-UP X4 AGC DESCRIPTION * Detect defective pixels while dark then saves the data for compensation. After starting STATIC DPC camera will close iris automatically. It is also recommended to cover lens during this process. * ON : Enable STATIC DPC * OFF : Disable STATIC DPC * Push ● button, camera will close the lens automatically and then detect defect pixels. * This is limit for white dots noise level caused by a defect pixel.
7-6. RS485 This is to set RS-485 with PELCO-D protocol for remote control. RS485 CAM ID DEFAULT 1 ID DISPLAY OFF BAUDRATE 2400 DESCRIPTION * Set camera ID No. 0 ~ 255 * OFF: camera ID No. is not displayed. * ON : Display the ID No on the top-right Set baud rate, 2400 / 4800 / 9600 / 19200 / 38400. 8. ADJUST 8.
ADJUST DEFAULT SHARPNESS 8 MONITOR LCD CRT LSC OFF VIDEO OUT RESOLUTION OFF FRAME RATE B-30/25P FOCUS ADJUST DESCRIPTION * Set sharpness level of picture. * Setting to high will cause more noise and a harsh image * Select LCD or CRT monitor. * LCD : Adjustable GAMMA, BLUE GAIN & RED GAIN. Higher GAMMA is increasing Contrast but looses visibility in dark areas. * CRT : Adjustable BLACK LEVEL, BLUE GAIN & RED GAIN * LSC (Lens shading compensation): enhance brightness of corners (both sides).
9. RESET 9. RESET Push enter button at FACTORY - RESET, return to factory default. 10. EXIT Save all then exit. Note 9. RESET Function List of Simultaneous Operation Push enter button at FACTORY - RESET, return to factory default. 10. EXIT 10. EXIT Save all then exit.
DIMENSIONS 2.68in (68.00mm) Unit of measurement: inch (mm) 2.33in (59.10mm) 4.96in (126.00mm) 2.42in (61.50mm) 3.74in (95.00mm) 8.07in (205.
SPECIFICATIONS SPECIFICATIONS Sensor Resolution S/N Video Output IR Illuminators IR Color Temp. IR Range Dynamic Intensity IR LEDs Lens Auto Focus Zoom Digital Zoom Minimum Illumination Day/Night Electronic shutter speed White Balance Brightness DSS (Sens-Up) DNR WDR Privacy Motion Detection ACE (Adaptive Color Enhancement) Advanced OSD Functions Advanced OSD Functions cont.
Other Products From VITEK On Cue HD-SDI Video Recorders VT-HDOCE Series On Cue Series 4, 8, and 16 Channel Real Time 1080p EX-SDI Digital Video Recorders • • • • • 4, 8 OR 16 CH EX-SDI / Analog Inputs (hybrid) with Full 1080p Camera Support Now Supporting Cable distance of up to 1000’ using RG59!* Hybrid Operation over COAX for HD-SDI, 960H, and D1 Cameras Simple plug and play, point-to-point connection from camera to DVR Real Time Recording on all channels at 1080p (VT-HDOC4E: 120fps), (VT-HDOC8E: 240fp
LIMITED LIABILITY WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.