VTC-C770DN 700TVL True Day and Night (ICR) Camera VITEK • 1/3” Sony High Density EXVIEW CCD • Sony Effio Digital Signal Processor • 700TVL High Resolution • .003Lux (F1.
VTC-C770DN WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person.
VTC-C770DN Table of contents 1. Safety Instructions and Notes…...................................................................................................... 3 2. General Descriptions............................................................................……………………………... 4 3. Supplied Items......................................................................................……………………………... 4 4. Part names…………………………….…...................................................…………………………... 5 5.
VTC-C770DN 1. Safety Instructions and Notes • Read instructions carefully before putting the camera into operation. • Keep the operating instructions in a safe place for later use. • The Standard Box Camera is designed for indoor use only and it must not be installed where exposed to rain and moisture. • Do not operate the cameras beyond their specified temperature, humidity or power ratings. • Never open the case of the camera because there are precision parts inside. An accident may result.
VTC-C770DN 2. General Descriptions VTC-C770DN (VTC-C770DN/PAL for PAL) is an ultra clear resolution camera that achieves 700TVL resolution and a crisp color reproduction with the use of Sony 960H EX-view CCD and Effio-E image signal processor.
VTC-C770DN 4. Part Names 4.
VTC-C770DN 4.2 Rear side view ⓑ ⓐ ⓒ ⓓ ⓐ OSD menu switches (Up/ Down/ Left/ Right / Enter) ⓑ Video Output Connector (BNC) ⓒ Power indicator LED ⓓ Power Input Terminal 5. Installation and Commissioning Instructions • Make sure the power is removed before the installation. • To apply power: First connect the low voltage (DC12V or AC24V). Then plug the AC adapter to AC outlets to avoid an improper reset from power jitter and a damage from the surge voltage when no load. 5.1.
VTC-C770DN 1. Point the camera at an object with sufficient contrast. The distance to the object should be longer than 1,000 x the focal distance. 2. Open the iris on the lens 3. Set the focus of lens so that the distance at the lens is close to infinity but not to exact infinity position. 4. Loosen Back focus Adjustment Lock: Screw one~two turns on the camera with industrial “+” driver 5. Rotate Back Focus Adjustment until the optimum focus is achieved. 6. Tighten Back focus Adjustment Lock Screw again.
VTC-C770DN 6. SETUP menu 6.1 In the menu Use Press , buttons to move the cursor and , buttons to change the settings. button to select or enter. button stands for MENU or ENTER button. 6.2 MAIN menu Follow the chart for submenu settings MAIN menu-1 MAIN menu-2 6.2.1 MAIN menu-1 MAIN menu-1 Default Descriptions SHUTTER /AGC AUTO Sets the parameters related to the shutter mode and AGC for AUTO and MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.
VTC-C770DN 6.2.1 MAIN menu-2 MAIN menu-2 Default NR - MOTION DET OFF Sets ON/OFF for enabling/disabling MOTION DET. See '6.10 MOTION DET menu' for the parameter settings. PRIVACY OFF Sets ON/OFF for enabling/disabling PRIVACY. See '6.11 PRIVACY menu' for the parameter settings. LANGUAGE ENGLISH CAMERA ID OFF CAMERA RESET Descriptions Sets the noise reduction parameters for NR MODE, Y LEVEL and C LEVEL. See '6.9 NR menu' for details. Selects the language out of 7 languages.
VTC-C770DN 6.3.1 SHUTTER/AGC>AUTO SETUP menu AUTO SETUP Default Descriptions Selects the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when MAIN>LENS>AUTO but it is fixed to SHUT if MAIN>LENS>MANUAL. AUTO IRIS - Light level is controlled by an auto iris lens only. For proper auto iris operation, the auto iris operation mode in MAIN> LENS>AUTO>MODE must be set to AUTO. HIGH LUMINANCE The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC> MANUAL> SHUTTER in this mode.
VTC-C770DN 6.3.2 SHUTTER/AGC>MANUAL SETUP menu MANUAL SETUP Default MODE SHUT +AGC Compensates the video level by the manual shutter control and AGC. SHUTTER 1/60 (1/50) Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000, 1/2000,1/4000 or 1/10000. Manual shutter is only useful when luminance is unchanged. AGC 6.00 Sets AGC gain in dB. Higher gain compensates for a brighter scene, but noise increases. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44 8dB.
VTC-C770DN IMPORTANT ACTIVITY!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final installation. Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode. If camera stays at NIGHT mode for more than 10sec, slightly increase „N→D THRES‟ and repeat the forementioned steps. If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY.
VTC-C770DN 6.6 PICT ADJUST menu To enter PICT ADJUST menu, press button at MAIN menu-1>PICT ADJUST. PICT ADJUST Default Descriptions MIRROR OFF Picture will be flipped horizontally if it turns ON. BRIGHTNESS 000 Increases or decreases the brightness of the picture. This is different from that of DC iris lens because it simply increases or decreases the digital gain of the video. Do not increase this too much or the dynamic range for the highlight area will decrease.
VTC-C770DN MANUAL white balance is a kind of fixed white balance which is user-programmable by B-GAIN. (R-GAIN will be automatically adjusted in accordance with B-GAIN) and useful only for the steady light. PUSH LOCK is a fixed white balance where the white balance is compensated only while the button is pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when button is released. To enter ATW (MANUAL) menu, press button at MAIN menu-1>WHITE BAL>ATW(MANUAL).
VTC-C770DN 6.8 ATR (Adaptive Tone Reproduction) menu The ATR feature improves the dynamic range and the visibility of the image by providing the optimal gradation compensation of the image in one field. This is achieved by two ways of image processing, luminance compression and contrast enhancement, so that the tone can be enhanced at highlighted and dark areas. To enter ATR menu, press ATR button at MAIN menu-1>ATR.
VTC-C770DN 6.9 BACKLIGHT menu To enter BACKLIGHT menu, press button at MAIN menu-1>BACKLIGHT. BLC OFF BLC ON HLC OFF HLC ON 6.10 NR menu To enter NR menu, press button at MAIN menu-2>NR. NR Default NR MODE Y/C Selects OFF, Y, C or Y/C which noise reduction is performed with. 006 Indicates the noise reduction strength for the luminance signal. Higher value performs stronger noise reduction and makes the image less sharp.
VTC-C770DN 6.11 MOTION DET menu Up to 4 motion detection areas are available and each area is programmable in size and location. The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION DET>BLOCK DISP are ON. To enter MOTION DET menu, press button at MAIN menu-2>MOTION DET>ON. MOTION DET Default Descriptions DETECT SENSE 080 Adjusts the sensitivity for detecting motion. A higher value is more sensitive.
VTC-C770DN PRIVACY Default Descriptions Selects one of AREA1~AREA8 to be adjusted. AREA SEL 1/8 TOP(BOTTOM) button moves up and button moves down the top (bottom) border of the selected window at AREA SEL. LEFT(RIGHT) button moves left and button moves right the left (right) border of the selected window at AREA SEL COLOR 1 Sets one of 8 colors for the selected mask window at AREA SEL. TRANSP 1.00 Transparency rate for the mask can be adjusted. 0.00 - Mask is fully transparent and not visible.
VTC-C770DN 6.15 CAMERA RESET Camera loads Factory defaults. To save them, go to SAVE ALL and press button. 6.16 EXIT Exits SETUP MENU and returns to the normal display 7. Specifications VTC-C770DN Model name VTC-C770DN/PAL Image Device 1/3” Sony High Density EXVIEW CCD Image Processor Sony Effio Digital Signal Processor Effective Pixels 976(H) x 494(V) 976(H) x 582(V) Scan Frequency 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal H.
VTC-C770DN 8. Dimensional Drawings 2.56in / 65mm 4.17in / 106mm 2.16in 55mm MAX 4.72in / 120mm 4.17in / 106mm 2.
VTC-C770DN 21
VTC-C770DN VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.
