VTC-C770WS Pixim Powered Ultra Dynamic Range Color CCD Camera with 700 TVL Short Body VITEK (Lens not included) • 700 TVL High Resolution • Pixim D8800C Seawolf Digital Imaging System CMOS • 0.00008 Lux (F1.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person.
Table of contents 1. Safety Instructions and Notes….................................................................................................. 4 2. General Descriptions............................................................................……………………………... 5 3. Supplied Items......................................................................................…………………………….. 5 4. Part names…………………………….…...................................................…………………..……….. 6 5.
1. Safety Instructions and Notes • Read instructions carefully before putting the camera into operation. • Keep the operating instructions in a safe place for later use. • The Standard Box Camera is designed for indoor use only and it must not be installed where exposed to rain and moisture. • Do not operate the cameras beyond their specified temperature, humidity or power ratings. • Never open the case of the camera because there are precision parts inside.
2. General Descriptions The VTC-C770WS camera is a superb ultra dynamic range camera that achieves 120dB max (102dB typical) of dynamic range of the image by implementing PIXIM's Seawolf digital imaging system.
3. Supplied Items 1 1 1 1 1 x x x x x VTC-C770WS Ultra Dynamic Color Camera Dust protection cap L-Wrench (1.5mm) Power Connector Installation and Operating Instructions 3. Part Names 3.1 Perspective 1 • 2 3 4 1. 2. 3. 4.
3.2 Rear Side view ⓑ ⓐ ⓒ ⓐ ⓑ ⓒ ⓓ ⓓ Video Output Connector (BNC) OSD Control Joystick (Up/Down/Left/Right/Enter) Power Input Terminal AUTO IRIS LENS CONTROL (DC LENS ONLY) - Lens Connector for Auto-iris lens (DC Drive) PIN 4 PIN 3 PIN 2 PIN No DC Iris 1 Damp(-) 2 Damp(+) 3 Drive(+) 4 GND PIN 1 4. Installation procedure 4.1 Installing the lens Before installing the lens, make sure the power is not connected to the camera. Do not touch the lens or filter surfaces. 4.
4.3 Power Supply Connections The VTC-C770WS camera works with 24VAC or 12VDC, dual voltage power. It does NOT require matching polar connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid possible ground-loop problems. Its wide operating voltage range of 10.5V-30V for DC and 12-28.8V for AC gives extra flexibility during installation. 5. Start up When the camera is powered properly, it initializes the internal parameters and the filter switch mechanism.
MENU Default Descriptions EXPOSURE Sets COLOR ROLL COMP. AE PREFERENCE, WDR CONTROL and SENSE-UP. DAY/NIGHT AUTO Sets OFF, AUTO or NIGHT OFF – Day/Night is disabled and camera works as a normal color camera. AUTO – Camera switches DAY from/to NIGHT automatically. N->D THRES, N<->D DELAY, BURST ON B/W can be set. See DAY&NIGHT AUTO SETUP for detail. NIGHT – Forced to remove IR cut filter and switch to B/W. LENS SELELT DC PICTURE CONTROL SPECIAL Selects the lens type, DC or MANUAL.
EXPOSURE Default In NTSC system, the color tone on the monitor may show a red or green hue. COLOR ROLL COMP.Descriptions - Reduces the color rolling under the fluorescent lighting. (NTSC system only) EXPOSURE COLOR ROLL Descriptions COMP. OFF level of the dynamic range control for each PRESETs. Medium WDR HIGH Increases theMODE-M dynamic- range control.the Some areaa may washed Compensates color highlight rolling when manual lens is out. used. CUSTOM... BLC...
IMPORTANT!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final step of installation. Factory Settings have DAY/NIGHT set to OFF. Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode. If the camera stays at NIGHT mode more than 10 seconds, increase N-->D THRES and repeat the fore-mentioned steps. If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY. DAY/NIGHT N-->D THRES.
6.6 LENS SELECT To enter LENS SELECT menu, press DC/ MANUAL AI LEVEL FOCUS ADJ. button at MAIN>LENS SELECT>DC or MANUAL. Default Descriptions 24 Lower values open the lens iris and increases the brightness and vice versa. Too high of a value reduces the amount of incoming light and may result in the camera not returning to DAY from NIGHT. - FOCUS ADJUST helps the Accurate focus adjustment regardless of DAY or NIGHT. Sometimes the focus looks fine tuned at day time but oocus at night time.
PICTURE PICTURE CONTROL PICTURE CONTROL CONTROL Factory Factory Default Factory Default Default Descriptions Descriptions Descriptions Sets Normal, ATW Desat, ATW Xtnd MANUAL. Sets ATW ATW to Normal, ATW Desat, ATW Xtnd or or MANUAL. ATW NORMAL Compensates automatically in Sets Normal, ––ATW Desat, ATW Xtnd or MANUAL. ATWATW NORMAL Compensates automatically in range range of of 2800K2800KATW NORMAL –7500K. Compensates automatically in range of 2800K7500K. ATW Compensates ATW DESAT DESAT –– 7500K.
SPECIAL Default Descriptions MOTION OFF If it is set to ON and motion is detected, MOTION message will appear on the monitor. See ‘6.8.1 MOTION ’ for settings. PRIVACY MASK OFF If set to ON, up to 6 privacy masks will be available. See ‘6.8.2 PRIVACY menu’ for settings. D-EFFECT LANGUAGE Sets FREEZE, FLIP, or D-PTZ. ENGLISH 3D NR VIDEO STANDARD English only. Determines the depth of Three Dimensional Noise Reduction. NTSC Able to switch between NTSC or PAL. FACTORY SET Sets previous setting.
6.8.2 PRIVACY AREA Up to 6 privacy areas can be programmed in size, position and mask color. Use joystick to change size, position and mask color. After pressing button at ON, the 1st zone appears on top-left corner in orange. The orange colored zone can be relocated with ‘up and down’, and ‘side to side’ buttons. After pressing button again, the 1st zone changes to blue. The blue colored zone can be resized with ‘up and down’, and ‘side to side’ buttons. Mask example after resizing.
8. Specifications Model name VTC-C770W S Image Device 1/3" CMY Color DPS SENSOR (Pixim Seawolf D8800C series) Effective Pixels 768(H) x 540(V) TV system NTSC, 525lines / 2:1interlace PAL, 625lines / 2:1interlace Scan frequency. 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal/Line lock (Default: Internal) H. Resolution 700TV Lines Sensitivity 0.0008Lux Class sensitivity (0.
9.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.