VTC-C960DS VTC-C960WS 750 TVL 960H True Day/Night CCD Cameras w/Effio-A/V Processing VITEK • VTC-C960DS: 750 TVL 960H True Day/Night CCD Camera w/Effio-A Processing • VTC-C960WS: 750 TVL 960H WDR Day/Night CCD Camera w/Effio-V Processing • 1/3” High density Sony CCD (960H) • High Resolution of 750 Horizontal Lines • Small scale design to fit in 5” dome enclosures such as the Pelco DF5 Housing • E-WDR by ATR-EX (Adaptive Tone Reproduction) (VTCC960DS) • True WDR (Wide Dynamic Range) (VTC-C960WS) • Sensiti
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent electric shocks and risk of fire hazards, do NOT use other than specific power source. CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
NOTICE The image used in this instruction manual are processed to help comprehension and may differ from actual appearance of the camera. Avoid installing areas where has shock or vibration which results in the problems. Pay attention to safety when laying the connection cable and observe that the cable is not subjected to heavy loads, kinks or damage and no moisture can get in. Never open the device such as boards. The warranty becomes void if repairs are undertaken by unauthorized persons.
p.03~04 Safety Precaution p.05 Contents p.06 Features p.07 Composition p.07 Dimensions p.08 Part Names p.09~10 Installation Instructions p.11~28 Operating Instructions p.
Key Features • VTC-C960DS: 750 TVL 960H True Day/Night CCD Camera w/Effio-A Processing • VTC-C960WS: 750 TVL 960H WDR Day/Night CCD Camera w/Effio-V Processing • 1/3” High density Sony CCD (960H) • High Resolution of 750 Horizontal Lines • Small scale design to fit in 5” dome enclosures such as the Pelco DF5 Housing • E-WDR by ATR-EX (Adaptive Tone Reproduction) (VTC-C960DS) • True WDR (Wide Dynamic Range) (VTC-C960WS) • Sensitivity of 0.
Operating Instruction L- Wrench: 1.5mm (1pc) Dust Protection Cap (1pc) Camera Dimensions (unit : mm) 2.89” 1.89” 2.38” 1.73” 2.09” Ø1.
Mount Holes (Top / Bottom) Flange Lock screw L-Wrench Dust Protection Cap Rear Case Back focus adjusting Flange Front Case REAR VIEW ① ③ ② ④ PIN 4 PIN 3 PIN 2 PIN 1 7 ① Video out connector(BNC) ② Power input terminal ③ OSD Control Joy stick ④ DC Auto Iris Lens connector Lens Connector for Auto Iris lenses No.
Installation and commissioning Instructions • Make sure the power is removed before the installation. • Follow the order for applying power. First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid an improper reset from power jitter and a damage from the surge voltage when no load. 1. Remove the dust protection cap from the lens mount. 2. Screw the lens onto the camera firmly. 3. Plug the lens plug into the lens connector on the rear of camera case. 4.
Using OSD Controller Setup menu can be accessed and controlled by OSD control joy stick on the rear of the camera unit. Five commands are available with the joy stick. The design of rear panel could be different according to the camera models. Description of the joystick operation 1) SET Key (●) : Access to the menu or enter the setting. To enter the main menu, press the Set Key down. 2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the cursor up or down.
OSD menu Startup Press the ‘OSD menu SET key’ down to access the setup menu mode. • / : Selects previous page or next page. • EXIT : Enters ‘EXIT’ menu. • RETURN : Returns to the previous menu. SETUP MENU SETUP MENU 1/2 SCENE SELECT PICT ADJUST EZOOM DIS PRIVACY MASK MOTION DET SYS SETTING EXIT 2/2 FULL AUTO LANGUAGE VERSION MAINTENANCE OFF OFF ENGLISH 1.
SCENE SELECT WDR / ATR-EX WDR for VTC-C960WS, ATR-EX for VTC-C960DS DNR LEVEL 3 DAY/NIGHT AUTO BURST OFF CNTL SIGNAL INT DELAY CNT 3 DAY->NIGHT 80 NIGHT->DAY 120 MODE AUTO IR AREA --- LEVEL 3 IR LED DAY/NIGHT COLOR NIGHT ON/OFF PATTERN SET1/2/3 POSH 480 POSV 290 LEVEL MID AUTO MODE GAIN CNTL ON MODE GAIN CNTL IR OPTIMIZER ON OFF (default) LENS SHD COMP OFF ON DEFOG OFF ON FLK LESS PICT ADJUST EZOOM ANTI CR AUTO / OFF / ON BRIGHTNESS 128 CONTRAST 32 SH
PRIVACY MASK TRANSP MOSAIC MOTION DET OFF ON DETECT SENSE 111 INTERVAL 0 BLOCK DISP OFF MASK AREA MONITOR AREA AREA SEL 1/4 AREA MODE OFF TOP BOTTOM LEFT RIGHT SYS SETTING LENS AUTO TYPE DC MODE AUTO ADJUST SPEED FLIP OFF / V / H / HV LCD / CRT CRT 30 CAMERA ID LANGUAGE English/ Spanish/ Russian/ Portuguese/ German/ French/ Chinese/ Japanese VERSION 1.01 MAINTENANCE W.PIX MASK MANUAL COMP REGISTRATION REG. POINT CURSOR COLOR BLINK REG.
OSD menu Setup Press the OSD menu SET key down to access the setup menu mode. SETUP MENU ADVANCED MENU 1/2 SCENE SELECT PICT ADJUST EZOOM DIS PRIVACY MASK MOTION DET SYS SETTING EXIT 1/2 FULL AUTO SHUTTER/AGC WHITE BAL HLC/BLC WDR/ATR-EX DNR DAY/NIGHT IR OPTIMIZER OFF OFF OFF AUTO ATW OFF WDR NIGHT ON RETURN 1. SCENE SELECT These options have been pre-configured at the factory for optimal performance.
1-1-3. FIX: Video level is fixed in any conditions by the setting of SHUTTER, AGC MAX. 1-2. WHITE BAL Can set the WHITE BALANCE mode. 1-2-1. ATW (Auto Trace White Balance): Automatically tracks the changes of color temperature and continuously adjusts the white balance. The white balance range is 1,800°K~10,500°K. Note: If you set to ‘CUSTOM’ mode in ‘SCENE SELECT’ menu, the ‘WHITE BAL’ sub-menu will be appeared ‘ATW/ PUSH/ USER1/ USER2/ MANUAL/ PUSH LOCK’ functions that you can select one.
> INDOOR : Optimized for Indoor installation and more easily compensates ATW for low color temperature such as incandescent lights. > SUNNY : Optimized for outdoor sunlight applications and more easily compensates ATW for high color temperature such as sunlight. > SHADE : Optimized for shade area compensation. > AUTO : Optimized for general scene. 1-3.
1-3-2. HLC: HLC clips out the highlight area and masks it as black color. Video will be clipped out and masked for the area which exceeds CLIP LEVEL. • CLIP LEVEL (default: 10): Defines the threshold level for HLC. Lower value masks more. 1-3-3. BLC: Sets BLC function enables or disables Note: BLC is available only in ‘CUSTOM’ scene preset. 1-4. WDR/ATR-EX 1-4-1.
1-6. DAY/NIGHT This function is used to control the setting during day-time and night-time operation. 1-6-1. AUTO AUTO mode in DAY/NIGHT is used only for a camera which does not have a light sensor. Camera switches DAY from/to NIGHT automatically along with the amount of light through the lens.
• NIGHT -> DAY (default: 120) NIGHT→DAY is a threshold level which determines to switch from NIGHT to DAY. Lower(Higher) value makes the camera switched from Night to Day at lower (higher) illumination. If it stays in Night(B/W) mode at day time, decrease NIGHT-> DAY threshold value until it just switches to Day * Examine and verify Day/Night operation according to IMPORTANT ACTIVITY 1-6-2. DAY : The camera is always in Color mode. 1-6-3. NIGHT : The camera is always in B/W mode.
1-7. IR OPTIMIZER This function is effective built-in LED models in NIGHT mode only. If subjects which can cause overexposure are located near the monitored area, you can adjust IR OPTIMIZER level or area. IR OPTIMIZER SETUP MODE IR AREA LEVEL IR LED COLOR NIGHT IR SHADE COMP IR LED AUTO AUTO --- 006 LEVEL MIN LEVEL MAX 002 DAY/NIGHT OFF OFF RETURN 255 RETURN 1-7-1. MODE : AUTO Reducing the over-saturation is automatically adjusted along with the location of the subject. 1-7-2.
1-8. LENS SHD COMP (default: OFF) This function is used to caculate the compensation data for lens shading. Convex shape of the lens causes the light to enter the camera unevenly and typically makes the center of the screen brighter than the rest. It is used to compensate for this undesirable effect and make the screen more even. Set to ‘ON’, you can adjust the shading PATTERN and POSITION. LENS SHD COMP PATTERN POSH POSV SET1 480 290 RETURN 1-9.
2-1. BRIGHTNESS (default: 120): Increases or decreases the brightness of the picture. This is different from that of DC iris lens and simply increases or decreases the digital gain of video. Do not increase this too much, the dynamic range for the highlight area will decrease. 2-2. CONTRAST (default: 033): Adjusts the strength of the image contrast. If set to too high, the dark area may loss detail and the high luminance area may saturate. 2-3.
5. PRIVACY MASK Sets ON/OFF for enabling/disabling PRIVACY. Up to 15 privacy areas are available and each area is programmable in size and location. The number of privacy areas is limited to four when MOTION DET > MONITOR AREA is ON. The privacy areas are masked with the color selected by PRIVACY MASK>COLOR. PRIVACY MASK SETUP AREA SEL DISPLAY POSITION COLOR TRAMSP MOSAIC 1/15 ON RED 1.00 ----- RETURN 5-1. AREA SEL (default: 1/15) : Selects one of AREA1~AREA15 to be adjusted. 5-2.
6. MOTION DET Up to 4 motion detection areas are available and each area is programmable in size and location. The motion is displayed by means of blocks when MOTION DET and MOTION DET>BLOCK DISP are ON. MOTION DETECTION DETECT SENSE INTERVAL BLOCK DISP MASK AREA MONITOR AREA 111 000 OFF RETURN 6-1. DETECT SENSE (default: 111) Adjusts the sensitivity for detecting motion. Higher value is more sensitive. 6-2.
6-5. MONITOR AREA Sets the MOTION DETECTION area on screen. MONITOR AREA AREA SEL AREA MODE TOP BOTTOM LEFT RIGHT 1/4 ON 03 04 04 08 RETURN 6-5-1. AREA SEL (default: 1/4) : Selects one of AREA1~AREA4 to be adjusted. Each area is displayed with the color. AREA1-Red, AREA2-Green, AREA3Blue, AREA4-Yellow 6-5-2. AREA MODE (default: OFF): Setting ON is activated the AREA SEL which you selected. 6-5-3. TOP/ BOOTTOM / LEFT / RIGHT Sets the AREA SEL box sizes and positions with four direction points.
7-1. LENS Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens only. 7-1-1. AUTO • TYPE (default: DC): This camera does NOT support video type auto iris lens. MUST BE SET TO DC ONLY. • MODE (default: AUTO): Lens iris is automatically controlled according to the scene light level. • ADJUST : Adjusts lens open control regardless of the light level. • SPEED (default: 30): Adjusts the iris control speed. The lower value is the faster speed.
● Use four direction buttons (▲/▼/◄/►) to move a block cursor in character table and press a set button (◙) to input the selected character. To move the character input position on CAMERA ID input line, move a cursor to ← or → on COMMAND LINE and press a set button on ← or →. ● CLR : To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press a set button (◙).
10-1. W.PIX MASK This function is used to compensate white pixels(defective pixels). MANUAL COMP REGISTRATION REG.POINT CURSOR COLOR BLINK REG. NUMBER AUTO COMP LEVEL1 LEVEL2 AUTO OFF WHITE OFF 3 / 64 RETURN RETURN 10-1-2. AUTO COMP : Setting for white pixels(defective pixels) compensation automatically. • LEVEL1 : Sets the threshold of the detection for white pixels. • LEVEL2 : Sets the threshold of the detection for very large white pixels. • AUTO : Starts the automatic detection of white pixels.
VTC-C960DS Image Device 1/3” High density Sony CCD (960H) Resolution 750TV Lines Effective Pixels Minimum Illumination 976(H) x 494(V) 0.0005 Lux (Sens-up Off) Lens mount CS Mount Day/Night True Day/Night by ICR WDR E-WDR by ATR-EX Noise Reduction XD-DNR (2D+3D DNR) Motion Detection 24x16 Grid Privacy Mask Up to 15 programmable mask areas White Balance ATW / PUSH / USER1 / USER2 / MANUAL / PUSH LOCK Auto Iris Control DC drive iris control. Level control is fixed internally.
VTC-C960WS Image Device 1/3” High density double scan Sony CCD (960H) Resolution 750TV Lines Effective Pixels 976(H) x 494(V) Minimum Illumination 0.001 Lux (Sens-up Off) Lens mount CS mount Day/Night True Day/Night by ICR WDR True WDR Noise Reduction XD-DNR (2D+3D DNR) Motion Detection 24x16 Grid Privacy Mask Up to 15 programmable mask areas White Balance ATW / PUSH / USER1 / USER2 / MANUAL / PUSH LOCK Auto Iris Control DC drive iris control. Level control is fixed internally.
Other Products From VITEK SPIRE Elite Series 960H Digital Video Recorders VT-SRE Series Spire Series 4, 8, & 16 Channel 960H Digital Video Recorders • Supports High Resolution 960H Cameras • 4, 8 or 16 Video Inputs with 1 HDMI, 1 Spot Monitor Output and 1 VGA output • H.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. Digital recording and storage products are also warranted for 3 years except for the hard drives which carry their own independent factory warranty from the hard drive manufacturer.
28492 Constellation Road Valencia, ca 91355 WWW.VITEKCCTV.
