Specifications

ManualsBrandsVitek ManualsHome building and DecorVTC-C960WS

VITEK

MIGHTY DOME

960H Cameras

750 TVL Dome Cameras Series

• 1/3” 960H High Density Double Scan Sony CCD

• 750 TVL High Resolution

• WDR - Wide Dynamic Range (Selected Models)

• True Day/Night by ICR

• IR Corrected Lens Options Lens options: 2.8-10mm and

9-22mm

• XD-DNR (2D+3D DNR) Noise Reduction

• Polygon Masking with 15 Programmable Zones

• OSD (On Screen Display) for Camera Setup

• Flush or Surface mount with included adaptor

• Defog video enhancement processing

• Ultra Versatile Design with Infinity Ball Mount for Any

Viewing Angle

• UTC CONTROL - Serial Control over Coax

• Secondary Video Output (Cable Included)

• Optional UTP Interface Available

• Fully Gasket Sealed with an IP-68 Water tight NEMA Rating

(Vandal Resistant Versions)

• Optional Heater / Blower Options Available (Vandal

Resistant Versions)

• Standard (-40°F) and Extreme Cold (-60°F) Temperature

Kits Available (Vandal Resistant Versions)

• Available in Ivory or Black

• 12VDC / 24VAC Dual Voltage Operation

Summary of content (38 pages)

PAGE 1
MIGHTY DOME 960H Cameras 750 TVL Dome Cameras Series VITEK • 1/3” 960H High Density Double Scan Sony CCD • 750 TVL High Resolution • WDR - Wide Dynamic Range (Selected Models) • True Day/Night by ICR • IR Corrected Lens Options Lens options: 2.
PAGE 2
TABLE OF CONTENTS BOX CONTENTS........................................................................... 2 INCLUDED ACCESSORIES.......................................................... 2 AVAILABLE MODELS/ACCESSORIES......................................... 3 MIGHTY DOME LAYOUT............................................................... 4 INSTALLATION.............................................................................. 5 JUNCTION BOX INSTALLATION.................................................
PAGE 3
BOX CONTENTS 1) Mighty Dome Camera 2) Accessories 3) VT-MD-2VOC (Secondary Video Output Cable) 4) Instruction Manual & Mounting Template INCLUDED ACCESSORIES Torx Wrench - (Vandal & IR Versions Only) Type #: T20 Length: 63mm / Diameter: 4mm Qty: 1 Phillips head Screws - (Vandal & IR Versions Only) For attaching the dome cover to the flush housing.
PAGE 4
AVAILABLE MODELS / ACCESSORIES Indoor Mighty Dome Configurations: VTD-MS2810DN: 960H - Indoor Effio-A Powered Day/Night Mighty Dome 750TVL Camera w/2.
PAGE 5
MIGHTY DOME LAYOUT 1) Lens 8) Dome Cover Ring 2) Power Input Connector(12VDC / 24VAC) 9) Flush Mount Base 10) Surface Mount Base 3) Video Output Connector - BNC 11) Assembly Screws - Torx M4x9 (Vandalproof) 4) Camera Holder and 2nd Video output 12) Assembly Screws - Phillips ST4x12 (Indoor) / Phillips M4x10 (Vandalproof / IR) 5) Ball with the Camera Assembly 6) Safety Wire 13) Mounting Screws - Phillips ST4x30 7) Bubble 4
PAGE 6
INSTALLATION 1) Dome Cover 1.1 Vandal Proof Domes - Use the provided Torx wrench to unscrew the vandal proof screws and remove the dome cover. 1.2 Indoor Domes - Turn the dome cover to the left to remove the dome cover. 2) Flush Mount Installation: Using four St4x30 screws, attach the flush mount base to a sturdy surface. Optional flush mount decorator plate. Model: VT-MD-FMP 3) Surface Mount Installation: Drill pilot holes at the mounting location using the provided mounting template.
PAGE 7
JUNCTION BOX INSTALLATION Mighty Domes can easily be flush or surface mounted to an electrical junction box (4S J-Box) using the pre-drilled mounting holes on either the surface mount housing or the the flush mount base.
PAGE 8
CONNECTIONS • Power connection: 12VDC or 24VAC dual input. • All Mighty Dome cameras come standard with a secondary video output. The secondary video cable (VT-MD-2VOC) is included in the box.
PAGE 9
LENS ADJUSTMENT 1) Loosen Zoom & Focus screws and make necessary adjustments as shown.
PAGE 10
3-AXIS GIMBAL ADJUSTMENT The Gimbal mechanism yields maximum rotation and placement as shown below.
PAGE 11
MIGHTY DOME FEATURES OSD menu Startup Press the ‘OSD menu SET key’ down to access the setup menu mode. • / : Selects previous page or next page. • EXIT : Enters ‘EXIT’ menu. • RETURN : Returns to the previous menu. SETUP MENU SETUP MENU 1/2 SCENE SELECT PICT ADJUST EZOOM DIS PRIVACY MASK MOTION DET SYS SETTING EXIT 2/2 FULL AUTO LANGUAGE VERSION MAINTENANCE OFF OFF ENGLISH 1.
PAGE 12
OSD Menu Features/Setup SCENE SELECT WDR / ATR-EX WDR for V-Series, ATR-EX for A-Series DNR LEVEL 3 DAY/NIGHT AUTO BURST OFF CNTL SIGNAL EXT1 DELAY CNT 3 DAY->NIGHT 80 NIGHT->DAY 120 MODE AUTO IR AREA --- LEVEL 3 IR LED DAY/NIGHT COLOR NIGHT ON/OFF PATTERN SET1/2/3 POSH 480 POSV 290 LEVEL MID AUTO MODE GAIN CNTL ON MODE GAIN CNTL IR OPTIMIZER ON OFF (default) LENS SHD COMP OFF ON DEFOG OFF ON FLK LESS PICT ADJUST EZOOM ANTI CR AUTO / OFF / ON BRIGHTNESS
PAGE 13
OSD MENU FEATURES/SETUP PRIVACY MASK TRANSP MOSAIC MOTION DET OFF ON DETECT SENSE 111 INTERVAL 0 BLOCK DISP OFF MASK AREA MONITOR AREA AREA SEL 1/4 AREA MODE OFF TOP BOTTOM LEFT RIGHT SYS SETTING LENS AUTO TYPE DC MODE AUTO ADJUST SPEED FLIP OFF / V / H / HV LCD / CRT CRT CAMERA ID OFF / ON 30 LANGUAGE English/ Spanish/ Russian/ Portuguese/ German/ French/ Chinese/ Japanese VERSION 1.01 MAINTENANCE W.PIX MASK MANUAL COMP REGISTRATION REG. POINT CURSOR COLOR BLINK REG.
PAGE 14
OSD Menu Features/Setup OSD menu Setup Press the OSD menu SET key down to access the setup menu mode. SETUP MENU ADVANCED MENU 1/2 SCENE SELECT PICT ADJUST EZOOM DIS PRIVACY MASK MOTION DET SYS SETTING EXIT 1/2 FULL AUTO SHUTTER/AGC WHITE BAL HLC/BLC WDR/ATR-EX DNR DAY/NIGHT IR OPTIMIZER OFF OFF OFF AUTO ATW OFF WDR NIGHT ON RETURN 1. SCENE SELECT These options have been pre-configured at the factory for optimal performance.
PAGE 15
OSD MENU FEATURES/SETUP 1-1-3. FIX: Video level is fixed in any conditions by the setting of SHUTTER, AGC MAX. 1-2. WHITE BAL Ability to set the WHITE BALANCE mode. 1-2-1. ATW (Auto Trace White Balance): Automatically tracks the changes of color temperature and continuously adjusts the white balance. The white balance range is 1,800 °K~10,500°K. Note: If you set to ‘CUSTOM’ mode in ‘SCENE SELECT’ menu, the ‘WHITE BAL’ sub-menu will appear.
PAGE 16
OSD Menu Features/Setup > INDOOR : Optimized for Indoor installation and more easily compensates ATW for low color temperature such as incandescent lights. > SUNNY : Optimized for outdoor sunlight applications and more easily compensates ATW for high color temperature such as sunlight. > SHADE : Optimized for shade area compensation. > AUTO : Optimized for general scene. 1-3.
PAGE 17
OSD MENU FEATURES/SETUP 1-3-2. HLC: HLC clips out the highlight (bright) area and masks it as black color. Video will be clipped out and masked for the area which exceeds CLIP LEVEL. • CLIP LEVEL (default: 10): Defines the threshold level for HLC. Lower value is more sensitive. 1-3-3. BLC: Sets BLC function enable or disable. Sets BLC function enable or disable Note: BLC is available only in ‘CUSTOM’ scene preset. 1-4. WDR/ATR-EX 1-4-1.
PAGE 18
OSD Menu Features/Setup 1-6. DAY/NIGHT This function is used to control the setting during day-time and night-time operation. 1-6-1. AUTO AUTO mode in DAY/NIGHT is used only for a camera which does not have a light sensor. Camera switches DAY from/to NIGHT automatically according to the amount of light through the lens.
PAGE 19
OSD MENU FEATURES/SETUP • NIGHT -> DAY (default: 120) NIGHT→DAY is a threshold level which determines to switch from NIGHT to DAY. Lower(Higher) value makes the camera switch from Night to Day at lower (higher) illumination. If it stays in Night(B/W) mode in day time, decrease NIGHT-> DAY threshold value until it just switches to Day * Examine and verify Day/Night operation according to IMPORTANT ACTIVITY 1-6-2. DAY : The camera is always in Color mode. 1-6-3. NIGHT : The camera is always in B/W mode.
PAGE 20
OSD Menu Features/Setup 1-7. IR OPTIMIZER This function is effective for built-in LED models in NIGHT mode only. If subjects which can cause overexposure are located near the monitored area, you can adjust IR OPTIMIZER level or area. IR OPTIMIZER SETUP MODE IR AREA LEVEL IR LED COLOR NIGHT IR SHADE COMP IR LED AUTO AUTO --- 006 LEVEL MIN LEVEL MAX 002 DAY/NIGHT OFF OFF RETURN 255 RETURN 1-7-1.
PAGE 21
OSD MENU FEATURES/SETUP 1-8. LENS SHD COMP (default: OFF) This function is used to caculate the compensation data for lens shading. Convex shape of the lens causes the light to enter the camera unevenly and typically makes the center of the screen brighter than the rest. It is used to compensate for this undesirable effect and make the screen more even. Set to ‘ON’, you can adjust the shading PATTERN and POSITION. LENS SHD COMP PATTERN POSH POSV SET1 480 290 RETURN 1-9.
PAGE 22
OSD Menu Features/Setup 2-1. BRIGHTNESS (default: 120): Increases or decreases the brightness of the picture. This is different from that of DC iris lens and simply increases or decreases the digital gain of video. Do not increase this too much, the dynamic range for the highlight area will decrease. 2-2. CONTRAST (default: 033): Adjusts the strength of the image contrast. If set to too high, the dark area may loss detail and the high luminance area may saturate. 2-3.
PAGE 23
OSD MENU FEATURES/SETUP 5. PRIVACY MASK Sets ON/OFF for enabling/disabling PRIVACY. Up to 15 privacy areas are available and each area is programmable in size and location. The number of privacy areas is limited to four when MOTION DET > MONITOR AREA is ON. The privacy areas are masked with the color selected by PRIVACY MASK>COLOR. PRIVACY MASK SETUP AREA SEL DISPLAY POSITION COLOR TRAMSP MOSAIC 1/15 ON RED 1.00 ----- RETURN 5-1. AREA SEL (default: 1/15) : Selects one of AREA1~AREA15 to be adjusted.
PAGE 24
OSD Menu Features/Setup 6. MOTION DET Up to 4 motion detection areas are available and each area is programmable in size and location. The motion is displayed by means of blocks when MOTION DET and MOTION DET>BLOCK DISP are ON. MOTION DETECTION DETECT SENSE INTERVAL BLOCK DISP MASK AREA MONITOR AREA 111 000 OFF RETURN 6-1. DETECT SENSE (default: 111) Adjusts the sensitivity for detecting motion. Higher value is more sensitive. 6-2.
PAGE 25
OSD MENU FEATURES/SETUP 6-5. MONITOR AREA Sets the MOTION DETECTION area on screen. MONITOR AREA AREA SEL AREA MODE TOP BOTTOM LEFT RIGHT 1/4 ON 03 04 04 08 RETURN 6-5-1. AREA SEL (default: 1/4) : Selects one of AREA1~AREA4 to be adjusted. Each area is displayed with the color. AREA1-Red, AREA2-Green, AREA3Blue, AREA4-Yellow 6-5-2. AREA MODE (default: OFF): Setting ON activates the AREA SEL which you selected. 6-5-3.
PAGE 26
OSD Menu Features/Setup 7-1. LENS Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens only. 7-1-1. AUTO • TYPE (default: DC): This camera does NOT support video type auto iris lens. MUST BE SET TO DC ONLY. • MODE (default: AUTO): Lens iris is automatically controlled according to the scene light level. • ADJUST : Adjusts lens open control regardless of the light level. • SPEED (default: 30): Adjusts the iris control speed. The lower value is the faster speed.
PAGE 27
OSD MENU FEATURES/SETUP 7-4. CAMERA ID Set ON/OFF for enabling/disabling of ID display. Factory default ID is Software version of camera. User programmed camera ID will be lost and restored with factory default ID by CAMERA RESET. Up to 40 characters can be input for camera ID. CAMERA ID SETUP VER-DN1.
PAGE 28
OSD Menu Features/Setup 10. MAINTENANCE Set the OSD menu user environments and Camera reset. MAINTENANCE MANUAL W.PIX MASK CAMERA RESET RETURN 10-1-1. MANUAL COMP : Setting for white pixel(defective pixels) compensation manually. • REGISTRATION : Detects each white pixel using the cursor. • REG. POINT : Displays white pixels in color which you detected. • CURSOR COLOR : Selects cursor color one of green, red, or blue. • BLINK : Sets the cursor blink or not. • REG.
PAGE 29
OSD MENU FEATURES/SETUP 10-2. CAMERA RESET This function is used to reset to the factory defaults of the camera settings. 11. EXIT Exits SETUP MENU and returns to the normal display. 11-1. SAVE : Save all the setting before exiting the setup menu. 11-2. NOT SAVE : Exit the setup menu without saving. 11-3. CANCEL : Cancel the exit mode. 11-4. BACK : Go back to the previous menu mode. HEATER / BLOWER OPTION (Vandal Versions) Detailed Specifications VT-MD-HB24 24 VAC Power Supply 10W (Heater) / .
PAGE 30
INDOOR WDR SPECIFICATIONS Detailed Specifications Image Device VTD-MS2810WDR 1/3” 960H High Density Double Scan Sony CCD w/Effio-V 750TV Lines Resolution 976(H) x 494(V) Effective Pixels 0.0001 Lux (F1.2@40 IRE, DSS x4) Minimum Illumination Lens Options VTD-MS922WDR 2.
PAGE 31
VANDAL WDR SPECIFICATIONS Detailed Specifications Image Device VTD-MVS2810WDR 1/3” 960H High Density Double Scan Sony CCD w/Effio-V 750TV Lines Resolution 976(H) x 494(V) Effective Pixels Minimum Illumination Lens Options VTD-MVS922WDR 0.0001 Lux (F1.2@40 IRE, DSS x4) 2.
PAGE 32
INDOOR DAY/NIGHT SPECIFICATIONS Detailed Specifications VTD-MS2810DN Image Device 1/3” 960H High Density Double Scan Sony CCD w/Effio-A VTD-MS1850DN 750TV Lines Resolution 976(H) x 494(V) Effective Pixels 0.0005Lux (Sens-up OFF) Minimum Illumination Lens Options VTD-MS922DN 2.
PAGE 33
VANDAL DAY/NIGHT SPECIFICATIONS Detailed Specifications VTD-MVS2810DN Image Device 1/3” 960H High Density Double Scan Sony CCD w/Effio-A VTD-MVS1850DN 750TV Lines Resolution 976(H) x 494(V) Effective Pixels 0.0005Lux (Sens-up OFF) Minimum Illumination Lens Options VTD-MVS922DN 2.
PAGE 34
IR SPECIFICATIONS Detailed Specifications Image Device VTD-MVS2810/L35 VTD-MVS922/L35 VTD-MVS1850/L35 1/3” 960H High Density Double Scan Sony CCD w/Effio-A 750TV Lines Resolution 976(H) x 494(V) Effective Pixels Minimum Illumination Lens Options 0.0005Lux (Sens-up OFF) / 0 Lux w/IR ON 2.
PAGE 35
DIMENSIONS Vandal 31 Indoor 34
PAGE 36
OTHER PRODUCTS FROM VITEK VTC-C960DS / VTC-C960WS 750 TVL 960H True Day/Night CCD Cameras w/Effio-A/V Processing • VTC-C960DS: 750 TVL 960H True Day/Night CCD Camera w/Effio-A Processing • VTC-C960WS: 750 TVL 960H WDR Day/Night CCD Camera w/Effio-V Processing • 1/3” High density Sony CCD (960H) • High Resolution of 750 Horizontal Lines • Small scale design to fit in 5” dome enclosures such as the Pelco DF5 Housing • E-WDR by ATR-EX (Adaptive Tone Reproduction) (VTC-C960DS) • True WDR (Wide Dynamic Range)
PAGE 37
OTHER PRODUCTS FROM VITEK SPIRE Elite Series 960H Digital Video Recorders VT-SRE Series Spire Series 4, 8, & 16 Channel 960H Digital Video Recorders • Supports High Resolution 960H Cameras • 4, 8 or 16 Video Inputs with 1 HDMI, 1 Spot Monitor Output and 1 VGA output • H.
PAGE 38
LIMITED LIABILITY WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.