ENVI Series ENVI Series 1.3 & 2.0MP Vandal Resistant Day/Night IR Bullet Camera Series w/150’ Range VITEK • 1/3” 1.3 & 2.0 Megapixel Progressive Scan CMOS image sensors • Up to 30fps live view @ 1920x1080p (2.0 MegaPixel Models) / 1280x1024 (1.3 MegaPixel Models) • 2.8-10mm Varifocal Auto Iris Lens • Integrated 850nm Infrared LEDs with up to 150’ Range • Dual Glass Compartments to Eliminate Glare • 2.
ENVI Series: VTC-IR40-N Table of Contents 1. Box Contents............................................................................................................................ 6 2. Included Accessories ................................................................................................................ 6 3. VTC-IR40-N Layout................................................................................................................... 7 3.1. Front View .................................
ENVI Series: VTC-IR40-N 12. System Configuration Menu .................................................................................................. 37 12.1. Server Name Setup..................................................................................................... 37 12.2. Date & Time............................................................................................................... 38 12.3. Admin Password ..........................................................................
ENVI Series: VTC-IR40-N 17.3. Reboot....................................................................................................................... 97 17.4. Factory Default........................................................................................................... 97 17.5. System Update ........................................................................................................... 98 18. ENVI Series Viewer...................................................................
ENVI Series: VTC-IR40-N 27. Quick Start Guide ............................................................................................................... 122 27.1. EN-V-R Configurator User Interface ........................................................................... 122 27.2. Searching for IP Devices ........................................................................................... 123 27.3. Registering IP Devices ........................................................................
ENVI Series: VTC-IR40-N 34.1.5. System, Network Configuration - IP-CCTV DNS ................................................ 161 35. IP-CCTV DNS Registration .................................................................................................. 162 36. IP-Device Registration ........................................................................................................ 167 36.1. IP-Device Registration (Manual) ............................................................................
ENVI Series: VTC-IR40-N 1. Box Contents 1) VTC-IRE40-N Long range Weatherproof IR Bullet camera 2) Mounting Accessories 3) VT-MD-2VOC (Secondary Video Output Cable) 4) ENVI Series CD & Mounting Template 2. Included Accessories 3mm Hex L-wrench Qty: 1 Wall mounting screws Qty: 4 Anchors If necessary, use the anchor to help secure the self tapping screws. Qty: 4 Sunshield with Attachment thumb screw Qty: 1 VT-MD-2VOC (Secondary Video Output Cable) For viewing video image during installation.
ENVI Series: VTC-IR40-N 3. VTC-IR40-N Layout 3.1. Front View 3.2.
ENVI Series: VTC-IR40-N 4. VTC-IR40-NInstallation • Make sure the power is not applied before the installation. 4.1. 1. 2. 3. 4. 4.2. Mounting The Camera Drill 4 holes into the wall or ceiling using the supplied template Insert the anchors into the drilled holes Match (foot mount holes) to the drilled holes Affix the mounting bracket by using supplied screws Connections 1. Power Depending on the type of installations, apply power to the camera by one of the three options below.
ENVI Series: VTC-IR40-N 2. Ethernet Connection Insert one end of the Ethernet cable into the network jack of your camera, and insert the other end into the data port (switch, router, etc) 3. Alarm Connections This camera support Alarm IN/OUT, Green = alarm IN, Blue = alarm OUT. (For more information, refer to Section 14.5DI (Sensor Input) / DO (Alarm Output) on page 79) 4. Audio In/Out This camera supports RCA Audio IN/OUT, (Audio IN White, Audio OUT Red) 4.3. Pan/Tilt Adjustment 1.
ENVI Series: VTC-IR40-N 3. Camera Rotation Inclination limited to +/-90° max. 4.4. Setup Menu 1.
ENVI Series: VTC-IR40-N b) Via the Web-Admin, Device Configuration> Camera & Motion> Camera Control. NOTICE: If the OSD menu is crushed and blurred, is due to small image size. Please have the secondaryimage size at 640x352 NOTE: For further information on OSD menu, refer to Section14.4Camera Control (Select Models) on page 55. 4.5. Removable Storage For recording directly on the camera you will need to install a SD card, this will allow you to play video directly from the camera.
ENVI Series: VTC-IR40-N 5. Camera Software Installation 1. Run IP Installer Software from the CD program on a computer that is on the same network as the IP camera. 2. StartIP Installer, by double clicking the icon “IP Installer” 3. After the program has started, the main window of IP Installer program will appear on the screen as shown below. 4. Search for the installed camera on the network by clicking the search product icon, the camera should appear as the image below. The default IP address is 10.
ENVI Series: VTC-IR40-N 7. After the camera was configured by the program automatically, you will be able to get access by a) Right click over the camera information, “Go Product Homepage” b) Click over the icon “Connect Product Homepage” 8. From the Home Page, you can “Live View”or administrate “Admin” the camera.
ENVI Series: VTC-IR40-N On Live View you will be able to see live video from your camera. NOTE: For more information, refer to Section 10. ENVI Admin Menu on page 35.
ENVI Series: VTC-IR40-N 6. VTC-IR40-N Features 1.3 & 2.0 MegaPixel Vandal Resistant Day/Night IR Bullet Cameras with 150’ Range • 1/3” 1.3 & 2.0 Megapixel Progressive Scan CMOS image sensors • Up to 30fps live view @ 1920x1080p (2.0 MegaPixel Models) / 1280x1024 (1.3 MegaPixel Models) • 2.8-10mm Varifocal Auto Iris Lens • Integrated 850nm Infrared LEDs with up to 150’ Range • Dual Glass Compartments to Eliminate Glare • 2.
ENVI Series: VTC-IR40-N 8.1. Installing IP Installer If the program is started from the CD supplied with Vitek products, insert the CD in to CD/DVD tray and check the installation file. If it is download or copied from the Internet or any other media, locate the file from the PC’s hard drive. You will see the icon as shown with the file name IP Installer_Setup_x.x.x.exe. The actual file name in your case may vary as the version changes. Double click the icon to star installation.
ENVI Series: VTC-IR40-N To continue the installation, click Next. The following window will be displayed for location to install. The default location for installation is C:\Program Files\IP Installer. It is recommended to install in this folder, if you want to change it to a different location, click the Browse button to choose location. Now click the Install button. You will see the progress of theinstall as shown below.
ENVI Series: VTC-IR40-N When the files are done copying, the following window will be shown. Click the Finish button to complete the installation.
ENVI Series: VTC-IR40-N 8.2. Uninstalling IP Installer If you want to remove the IP Installer program from your PC, click Start > All Programs > IP Installer > Uninstall. You may be prompt to continue running theuninstall program. Click onthe Yes button, then the following window will be shown on the screen. Click on the Next button and you will see the following window.
ENVI Series: VTC-IR40-N Click on the Uninstall button to start removing the IP Installer program from your computer. The following window will be displayed.
ENVI Series: VTC-IR40-N 9. Using IP Installer 9.1. Starting the Program Once IP Installer program has been installed on your computer, a shortcut icon should be created on the desktop of your computer.You can start IP Installerby double clicking the icon. Or you can also start the program by clicking Start > All Programs > IP Installer > IP Installeras shown below. After the program has started, the main window of IP Installer program will appear on the screen as shown below.
ENVI Series: VTC-IR40-N 9.2. Automatic IP Setup Configure the network setting of selected IP device in Automatic mode. Manual IP Setup Configure the network setting of selected IP device in Manual mode. Connect Product Homepage Connect to the server homepage of the selected IP device. Update Firmware Update the firmware of the selected IP device. Filter Configuration Define the range of MAC and IP addresses to search.
ENVI Series: VTC-IR40-N Manual Network Setup Configuring the network parameters of the devices in the list can be started either by highlighting and right clickingmouse button or by clicking Manual IP Setupbutton on the main Toolbar. When one IP device is selected, the following screen will appear MAC Address MAC address of the selected device is shown. Server Name Input desired name of camera i.e. Lunch Room HTTP Port Input port number to access IP devices homepage via web.
ENVI Series: VTC-IR40-N Network Authentication (Admin Password) Save Configuration Option General network parameters are required in this part. Please contact your network administrator for detail.(IP Address, Netmask, Default Gateway, DNS1, DNS2) Password for the IP device. (Default password for Vitek products is “root” unless already changed) Select whether the configured contents is to be saved in the Camera memory or not.
ENVI Series: VTC-IR40-N Model Model Numbers of the IP devices that you selected. MAC Address MAC address of the selected device is shown. Server Name Name of the selected IP device. IP Type How to assign IP address to the device (Select Static here for Manual IP Setup) IP address, Netmask, Gateway, DNS1, DNS2 General network parameters are required in this part. Please contact your network administrator for detail. HTTP Port HTTP port number of the IP device for web access to homepage.
ENVI Series: VTC-IR40-N Server Name Name of the selected IP device. HTTP Port HTTP port number of the IP device for web access to homepage. IP Type How to assign IP address to the device (Select Static here for Manual IP Setup) Network General network parameters are required in this part. Please contact your network administrator for detail. (IP Address, Netmask, Default Gateway, DNS1, DNS2) Authentication (Admin Password) Password for the IP device.
ENVI Series: VTC-IR40-N Note: If your network has more than one IP address Zone at the same time, the confirmation window will be displayed as below. You need to choose the one you are going to use for your IP devices. 9.4. Using DHCP Server If your network has a DHCP server running for assigning IP addresses, you may choose to let it assign IP addresses to the IP devices on the list. To do that, first open the Network Setup window either by Manual IP Setup or Automatic IP Setup procedure.
ENVI Series: VTC-IR40-N For setting up other fields on the setup window, refer toSection0Manual Network Setupon page 23. After filling the fields with appropriate values, click Set button to apply the changed values to IP device. If you don’t want it, click Cancel button to restore the previous values. 9.5. Using PPPoE If your network environment is based on PPPoE connection, you’ll need to choose PPPoE on IP Type selection.
ENVI Series: VTC-IR40-N MAC Address MAC address of the selected device is shown. Server Name Name of the selected IP device. HTTP Port HTTP port number of the IP device for web access to homepage. IP Type How to assign IP address to the device (Select PPPoE in this mode) PPPoE User Authentication for PPPoE Connection. • PPPoE User: Enter User ID. • PPPoE Password: Enter Password for the User ID. • PPPoE Password Confirm: Enter the same Password again.
ENVI Series: VTC-IR40-N 9.6. Updating Firmware Once IP devices are searched and shown on the screen as functioning successfully, you can update the firmware of them in “IP Installer” program. To do that, first check the firmware version of the device, which you can find on the IP Installer window. In the above picture, the firmware version of this product is 4.14-01-ds while the latest firmware version available is 4.16-B0-ds-VI as you could see at Vitek’s homepage (http://www.vitekcctv.com/Downloads.
ENVI Series: VTC-IR40-N After clicking OK the following window will be displayed. Note: Do not CLOSE window until completed, to avoid permanent damage to the camera. You can also select multiple IP devices at the same time, and have them start firmware updating in a single step. Select the files to update by holding CTRL key and selecting which IP devices to update Click Start Update button. You will see the update window brought up with multiple IP devices listed.
ENVI Series: VTC-IR40-N 9.7. Filter Configuration When you need to search only for the IP device having a specific range of MAC or IP addresses, you can do it by using this feature. To set the search condition, click Filter Configuration button on the Toolbar, then the following window will show up on the screen. The first six HEX characters are already filled in with 1C:7C:45, which is the MAC prefix for Vitekproducts. Put a checkmark inMAC Address or IP Range to set the range for searching.
ENVI Series: VTC-IR40-N To start searching with this condition now, click Search Product button on the toolbar. The program will start searching and show the result after a moment. 9.8. Live View Once searching and configuration on IP devices are done, you should make sure that the IP devices are accessible with the new settings. The best way to do it is by connecting to the homepage of each IP device’s built-in server, and starting Live View feature.
ENVI Series: VTC-IR40-N Click Live View on the top right of the window, then ENVI Series Viewer ActiveX program will be started. If you have not installed the ENVI Series Viewer program before, it will ask for a confirmation to install it. Allow it and you will be able to find out whether the configuration by IP Installer program is properly done. Note: Refer toSection 18. ENVI Series Vieweron page 101for detailed information about the ENVI Series Viewer ActiveX program.
ENVI Series: VTC-IR40-N 10. ENVI Admin Menu After connecting to a VITEKENVI Series camera via web browser, you’ll find the web page as shown below. The upper rightmost item of the menu is Admin; this is where you can set up most of the features in the VITEK camera you’re connected to. 10.1. EnteringAdmin Menu Click Admin then you’ll see a login window.In the login window, enter root for both ID and password as they are the factory defaults. Press Enter key or click OK.
ENVI Series: VTC-IR40-N 10.2. Admin Menu Structure The following table shows the hierarchy of the Admin menu structure that we’re going to deal with in this manual. 11. QuickConfiguration In Quick Configuration, you will be able to set up many of the essential parts of the configuration in a simple manner without going into details. Selecting Quick Configuration gives you the menu as seen below. You can perform each setup by clicking the one you would like to configure. 11.1.
ENVI Series: VTC-IR40-N 11.4. Step 4: IPCCTVDNS.COM When VITEK Server is used in a Dynamic IP environment, it is required to utilize IPCCTVDNS.com feature. Refer toSection 35. IP-CCTVDNS Registration on page 162for setup information. 11.5. Step 5: Recording Configuration Vitek cameras with MicroSD card can be configured for recording options in this section.Refer to Section 16.1SD / MicroSD Card Configuration on page 90to see how to set up. 11.6.
ENVI Series: VTC-IR40-N As an administrator, you can change the name of the camera/ server, but other values are not allowed to be changed. To change the camera/ servername, enter a new name in the Server Name field. You may use up to 21 alphanumeric or up to 10 Unicode characters. Tab or any other special characters are not allowed. Click Apply button to save the setting and it will take effect immediately. 12.2. Date & Time Click Step 2 on Quick Configuration.
ENVI Series: VTC-IR40-N 12.3. Admin Password To change the password for the administrator, click Admin Password in System Configuration menu. Default ID for admin account is fixed as “root” and is not allowed to change. In Old Password field, enter the current password. In both New Password and Confirm Password fields, enter the same new password. The password must be between 4 and 23 alphanumericcharacters.Click Apply button to put it into effect.
ENVI Series: VTC-IR40-N Enter aUser ID between 4 and 23 alphanumeric characters. In bothPassword and Confirm Password fields, enter the identical password respectively. The password must be between 4 and 23 alphanumeric characters. In Name filed, enter the user’s name up to 23 alphanumeric characters. Now select one of the four items from System Resource Access Permission, which defines the permission level for registered users to the VITEKcamera.
ENVI Series: VTC-IR40-N • VS Module ID: VS Module is a network device that has been registered in theVITEKcamera • Camera No.: Among the cameras of the VS Module select one to set up. (between all,1or2) • Alarm Control: Determine if Alarm control is to be allowed.(selected models) • Audio Control: Determine if Audio Control is to be allowed.(selected models) After finishing the registration process, click Applybutton to add the user. 12.5.2. Edit To edit a user account, select Edit.
ENVI Series: VTC-IR40-N 13.1. Static IP Configuration Select Network Configuration under Network configuration For static IP, select Static IP and input IP address, NetMask, Gateway, DNS1, DNS2 and click apply to save settings. After apply, program will ask to close web browser for updates, which will take 20~30 seconds. If Back button is clicked all values will be discarded. If Refresh button is clicked, the program will load previous values. 13.2.
ENVI Series: VTC-IR40-N 13.3. PPPoE Configuration PPPoE is used to connect VITEK products to a PPPoE modem provided by the ISP. Since PPPoE needs verification, ID and a password are necessary to access the network. Type in PPPoE user ID and password 13.4. Network Ports In this configuration, you set up the HTTP port for VITEKcameras to communicate with the Client PC. HTTP Port is the network port that is used when a Client PC connects to the VITEKcamera Web page.
ENVI Series: VTC-IR40-N 13.5. Bandwidth Control Configuration Bandwidth control is for limiting maximum network traffic. If it is enabled with Bandwidth limits, maximum data size transferred from VITEKcameras won’t exceed bandwidth limits set by users. If transferred data is exceeded, part of the data will be randomly lost. If multiple users try to access a VITEKcamera when bandwidth control is enabled, users connected to the VITEKcamera will share network bandwidth limit.
ENVI Series: VTC-IR40-N 13.7. Network Status Notify This feature helps to send updated network status information to registered email address if any changes happen. This function will work under DHCP or PPPoE. If Network Status Notify is set to Enable, VITEKcameras network status will be emailed to a specific person in case of the following events: • When it is set to Dynamic IP in theNetwork Configuration menu, and the VITEKcamera has been given a new dynamic IP address and connects to the network.
ENVI Series: VTC-IR40-N First, select Enable to use the feature. Then enter the address of the SMTP server which is needed for email service. If your SMTP server requires a user ID and a password for authentication, you will have to Enable Authentication Loginand enter the user ID and Password. In Sender field, enter your email address or other meaningful words that will show the message was sent from the VITEKcamera as a notification.
ENVI Series: VTC-IR40-N . 13.9. Port Forwarding & UPnP UPnP(Universal Plug and Play)is a kind of network protocol to help users to find and configure network products in the same local network area. Port forwarding is to assign a certain network port to a network product so users can access it from outside of the Local Area Network. Generally, port forwarding can be configured from the network router.
ENVI Series: VTC-IR40-N 13.10. RTP/RTSP Setup Factory default is Enable to be used with other manufactures VMS software’s RTSP (Real-Time Streaming Protocol) is a protocol to transfer video and audio streams over the network. Any application supporting Standard RTSP can be used for VITEKcameras. Quick Time Player or VLC program can be used withthis; it may not be supported in the environment within a firewall.
ENVI Series: VTC-IR40-N Service RTSP Port Enable: Start RTSP service Disable: Stop RTSP service In normal case, use default port number 554 to connect to RTSP service. If not using port 554, enter the port number you want to use. e.g.) port number 445==>rtsp:// network video server ip address:445/cam0_0 RTP Start Port The starting number of the port for video transfer. Each time video transfer connection is made, the port number also increases. Multicast Address Address for multicast video transfer.
ENVI Series: VTC-IR40-N To Add a Privacy zone click Newbutton, aGreen-colored box will appear, click on the Green box and it will turn Red, at this point you can resize it by clicking and holding any corner and drag to desired size. To relocate box click and hold anywhere inside the box and drag to desired location.
ENVI Series: VTC-IR40-N Users can add up to 8 Privacy Zones per screen by repeating above steps. If you add more than 8, an error message will display on the screen. To delete a privacy zone, click the zone and click Delete button followed by Apply button.
ENVI Series: VTC-IR40-N 14.2. Camera & Motion This menu is used to set up the selection of video format, data added to video data, encoding speed, audio control, image resolution, video quality, motion detection, etc. Click Camera & Motion on Device Configuration menu. The configuration menu will be displayed, and it may be different between VITEKcameras. • M-JPEG: This format requires much higher network bandwidth than H.264 compression.
ENVI Series: VTC-IR40-N • Video with Flexible Extra System data: If Enabled, video data will contain UART sensor data from COM port..(Feature not available on this model) • Video with user defined message: If Enabled, video data will contain the user-defined data. (Reserved Field).(Feature not available on this model) • Video with PPP status: If Enabled, video data will contain PPP connection status..
ENVI Series: VTC-IR40-N NTSC - 704 x 480 352 x 240 160 x 112 PAL - 704 x 576 352 x 288 160 x 144 VGA - 640 x 480 320 x 240 160 x 112 1.3M Pixel 1280 x 1024 640 x 480 320 x 240 160 x 112 2.0M Pixel 1920 x 1080 640 x 480 320 x 240 160 x 112 14.3. Camera Configuration On the lower part of Camera & Motion Configuration menu, select a channel to configure. In the example shown below, Primary Stream is set to H.264 for compression format.
ENVI Series: VTC-IR40-N 14.3.1. Rate Control Mode 14.3.2. Image Quality Setup In Image Quality level setup, select “Low Compression” for higher image quality, but it requires higher network bandwidth. Selecting the “Lowest” requires lower network bandwidth, but gives decreased image quality. After configuration is finished, click Apply button to save the setting. If you click Default button, the entire configuration will be reset to the original values.
ENVI Series: VTC-IR40-N Exposure AGC (Automatic Gain Control) You can adjust the AGC manually 56
ENVI Series: VTC-IR40-N SENS –UP Allows color video in low light environment without noise (static).
ENVI Series: VTC-IR40-N DEFOG Enhances image in foggy weather.
ENVI Series: VTC-IR40-N AREA To adjust the Area where “BLC” is relevant.
ENVI Series: VTC-IR40-N RET Return to Exposure Menu or select arrow right to AGAIN to redo area.
ENVI Series: VTC-IR40-N BACKLIGHT >>HSBLC This function is to prevent against the intense light from washing out the picture, such as headlights from a vehicle. SELECT AREA 1 You can select area 1 thru 4 by clicking right or left button.
ENVI Series: VTC-IR40-N POSITION Using the UP / Down / Left / Right position the area where needed, then click ENTER Size Using the UP / Down / Left / Right position the size needed then click ENTER 62
ENVI Series: VTC-IR40-N RET Return to Exposure Menu or select arrow right to AGAIN to redo area.
ENVI Series: VTC-IR40-N Mode Day or Night for highlight masking BLACK MASK Turns masking ON and OFF DEFAULT 64
ENVI Series: VTC-IR40-N Defaults HSBLC selection RETURN Return to EXPOSURE screen RETURN Return to SETUP screen LENS>>DC This camera is equipped with an Auto Iris Lens “DC” for the automatic adjustment of lighting conditions.
ENVI Series: VTC-IR40-N MODE Adjust mode to the proper application (indoor / outdoor) RETURN Return to SETUP screen LENS>>MANUAL FUNCTION NOT AVAILABLE FOCUS ADJ.
ENVI Series: VTC-IR40-N D/N DWELL Adjust the time between day and night when POP on CVBS is turned on POP ON CVBS Start sequencing between day and night images for focusing RETURN Return to SETUP screen DAY & NIGHT DAY&NIGHT menu can be set to AUTO, COLOR, B/W or EXT.
ENVI Series: VTC-IR40-N In AUTO, camera determines DAY or NIGHT by the incoming light level through the lens only and IR CUT FILTER switches following the DAY/NIGHT modes. In COLOR, camera disables DAY/NIGHT feature and works as a regular color camera and IR CUT FILTERis inserted to cut out the infrared spectrum from the light. In B/W, camera disables DAY/NIGHT feature and works as a regular B/W camera and IR CUT FILTER is removed to pass the infrared spectrum from the light.
ENVI Series: VTC-IR40-N NR(Noise Reduction) 2D&3DNR are very sophisticated and powerful noise reduction technologies at low light. 2DNRThe process of removing image noise from a video signal by applying a digital comb filter 3DNR A 3D filter reduces the noise caused by movement resulting in less blur. Too strong 3DNR reduction results in the tail effect of a comet or motion blur forma fast moving target in low light.
ENVI Series: VTC-IR40-N 2DNR. ON reduces the noise that can be found in low light images 3DNR ON Reduces the noise caused by movement. Start / End of noise reduction with respect to light level can be set to required levels START THRES sets the point from which 3DNR levels starts when the illumination level dims. Higher setting starts3DNRat higher light level. END THRES sets the point from which 3DNR stops when the illumination level is higher. DEPTH sets the strength of noise reduction for 2D&3D.
ENVI Series: VTC-IR40-N SMART NR continuously monitors motion on the screen.When no motion is detected, 3DNR is automatically activated for the maximum reduction of noise at low light. 3DNR becomes immediately deactivated upon motion. This will save HDD space PICT ADJUST (Picture Adjustment) InPICT ADJUST menu, WHITE BAL, SHARPNESS, MONITOR, OSD COLOR, CORNER COMP andD-EFFECT can be set.
ENVI Series: VTC-IR40-N SHARPNESS Increases or decreases the sharpness of the picture.Too much sharpness makes the image harsh and shows more noise and line flicker at the edge of objects in the picture. MONITOR Sets LCD or CRT. LCD: GAMMA, BLUE, GAIN or RED GAIN is adjustable for the best view with LCD monitor. Low GAMMA compensates for dark areas, slightly but contrast becomes low. High GAMMA increases contrast but looses the visibility of dark areas.
ENVI Series: VTC-IR40-N OSD TEXT COLOR - Can be change to 1 of 8 colors. Selected color is applied to menu text and cameratitle. OUTLINE – Makes the letters bold BACK TABLE - Is the color bar where the cursor is located CORNER COMP Enhances brightness of the corners caused by the lens, or the narrow angle of IR LEDs. Picture could be noisy when ON.
ENVI Series: VTC-IR40-N MIRROR:OFF(normal display), MIRROR(Left & right mirrored), V-FLIP(upside down) and ROTATE(H/V-FLIP) D-Zoom (Function not available) NEG.IMAGE: If set to ON,. SPECIAL In SPECIAL menu, CAM TITLE, MOTION, PRIVACY, LANGUAGE, PIXEL COM and TV SYSTEM can be set.
ENVI Series: VTC-IR40-N CAM TITLE: OFF / ON. When on click ENTER Up to 15 characters can be use on camera title line, use ▲,▼,◀,▶ to navigate around chart, when letter or character is flashing click ENTER, continue this in till completed. When done arrow over to POS (POSITION), click ENTER and position camera title to desire location, click enter to return to previous screen and arrow over to END and click ENTER.
ENVI Series: VTC-IR40-N Note USE Privacy settings under Device Configuration LANGUAGE English, Japanese, Chinese 1, Chinese 2, German, French, Italian, Spanish and Polish.
ENVI Series: VTC-IR40-N ON - Enables LIVE DPC and compensates the defective pixels whose magnitude exceeds the threshold by set level. OFF - Disables LIVE DPC. Note: High setting of LEVEL in LIVE DPC reduces the sharpness STATIC DPC Detects the defective pixels with lens closed and saves the data for compensation ON -Enables the compensation for the detected defective pixels. OFF - Will not apply the compensation. DO STATIC Camera closes the lens automatically and detects the defective pixels.
ENVI Series: VTC-IR40-N STATIC THR For white dots (noise) caused by a defective pixel exceeding the levels will be compensated. The lower the setting the more pixels will be compensated up to 1024 staring from top to bottom. PIXEL BOOST It is easier to detect defective pixels with PIXEL BOOST, but the higher the level the more noise might be detected by mistake and give a false reading.
ENVI Series: VTC-IR40-N Factory Defaults the camerasettings (Not the network settings) EXIT Exits the Set up menu 14.5. DI (Sensor Input) / DO (Alarm Output) Select DI/DO from Device Configuration menu to name and configure Sensor Input and Alarm Output. After configuring, select DI Status/DO Control on Device Configuration menu to manually control DO (Alarm Output) and check status of DI (Sensor Input).
ENVI Series: VTC-IR40-N DI/DO functionality can be set to either Normal Open or Normal Closed type as follows. • Normal Open Type: Normal is OPEN, and goes CLOSED when triggered by an event. • Normal Close Type: Normal is CLOSED, and goes OPEN when triggered by an event. Note: Make sure the type of the sensor and use it correctly to the type. If a Sensor Input is not used, it must be set to Normal Open Type to avoid a false input.
ENVI Series: VTC-IR40-N 15. Advanced Configuration There are two types of advanced service, one is Buffered Service and the other is Periodic Service. In Buffering Service, a series of images are continuouslybeing stored in a buffer memory of thecamera/server for a certain period of time. When the camera/server is triggered by an event or schedule, the images or alarm statusjust before and after the event/schedule are reported to you by email or buffered FTP services.
ENVI Series: VTC-IR40-N 15.1. Advanced Services Pre-Alarm buffer size and buffering speed can be defined here. • Pre-Alarm Buffer Size: You can set the buffer size which will store the images before event. The unit is in frame, and each channel can be set with different values. The total number of frames for Pre-Alarm Buffer and Post-Alarm Buffer is limited to 10 frames. • Pre-Alarm Speed: You can set the buffering speed. If it’s set to Fastest, the server will store images as fast as it can.
ENVI Series: VTC-IR40-N 15.1.1. E-mail Service Configuration Email configuration is set up here for Alarm in case any event occurs. Item Description Camera 1~2 Select a channel to be configured for email notification Service Select Enable in order to use this service SMTP server address Enter SMTP server’s address for sending email.
ENVI Series: VTC-IR40-N E-mail Service Setup for Each Channel For each channel, the following items can be configured for email service: Condition, Post-Alarm Buffer Size, and Post-Alarm speed. The content of text message and display style of DI value can be configured as well. Item Condition 1 ~ Condition 3 Pre-Alarm Buffer Size Description Select a condition for Email service to be activated. The Buffer size assigned for Pre-Alarm.
ENVI Series: VTC-IR40-N After finishing setup, click Save button to apply. If you don’t want to change, click Back button. Condition, Schedule & Event Configuration If you click on a Condition link, the Advanced Service windows is displayed as shown below. Alarm Service is activated only when the conditions in Advanced Services are met. Item Description Service This shows what service this condition is for.
ENVI Series: VTC-IR40-N 15.1.2. FTP (Buffered) Service Configuration Item Description Camera 1 - Camera 2 Select which channel to set up for FTP (Buffered). Service Server Address Base Directory Name Base File Name Select Enable to use the FTP (Buffered) service. Otherwise select Disable. FTP Server Address. The directory in FTP server where the data will be uploaded. (You should make the directory in the FTP server before using the service.
ENVI Series: VTC-IR40-N User ID Password FTP Control Port Date Description Mode Connection Mode Enter a User ID to log in to FTP server. Enter the Password for the user ID to log in to FTP server Port number for FTP server (Normally 21 is used) Select Date Display Style:American, European or ISO Standard Select connection mode for FTP server If Directory Name is checked, new directory is created with server Server Name name. If File Name is checked, new file is created with server name.
ENVI Series: VTC-IR40-N Item Description Condition 1 ~ Condition 3 Select a condition for FTP (Buffered) service to be activated. Up to 3 conditions can be set. Pre-Alarm Buffer Size The Buffer size assigned for Pre-Alarm. Check Video buffer Click this link to go to Advanced Services for video buffer setup. Pre-Alarm Images The number of image frames to store before Alarm. Post-Alarm Images The number of image frames to store after Alarm.
ENVI Series: VTC-IR40-N Item Description Camera 1 - Camera 2 Select which channel to set up for FTP (Periodic) service Select Enable to use the FTP (Periodic) service. Otherwise select Disable. Service Server Address FTP Server Address. Base Directory Name The directory in FTP server where the data will be uploaded. (You should make the directory in the FTP server before using the service.) Base File Name The base file name of the data to be uploaded in FTP server.
ENVI Series: VTC-IR40-N FTP (Periodic) Service Configuration for each channel Item Description Condition 1 ~ Condition 3 Select a condition for FTP (Periodic) service to be activated. Up to 3 conditions can be set respectively. FTP interval (msec) Select the speed of images to send in FTP(Periodic) service After finishing setup, click Save button to apply. If you don’t want to change, click Back button. 16.
ENVI Series: VTC-IR40-N If entire SD information is showing “-NONE-” this means SD card is not formatted, in this case click Note: Be sure to turn off the device before installing a SD card. Otherwise, the SD card may become defective. Always check the recommended type of SD card because non-conforming SD cards can cause abnormal behavior of the system.
ENVI Series: VTC-IR40-N Note: if program is terminated during the “Format” process SD Card might be damaged After formatting is completed the following screen will be displayed Click OK and you will be brought back to the “SD Status & Format screen” click on “Reboot” wait approximately 30 seconds and log back into the Admin screen.
ENVI Series: VTC-IR40-N 16.2. Recording Configuration with SD card Each camera has 2 streams (referred as Camera 1 / Camera 2 (see image below)) which can be configured for recording options in this section. Configuration items include motion detection recording, 24-hour continuous recording, event-driven recording, etc. You can find out the list of streams (camera 1 / camera 2) with recording capability by clicking Recording Configuration on the left side of your screen.
ENVI Series: VTC-IR40-N Select Condition 1andthe following window will be display.
ENVI Series: VTC-IR40-N By clicking on Enable you will be able to select your mode (Always, Schedule only etc). in this example we will be selecting “Event Only”. Schedule Under Scheduleyou can select time and date for motion recording if left blank motion recording will be 24hrs, 7 days a week. In this example we will be leaving it blank (24/7). Event Under Event click Motion Detection (stream 1 / stream 2). Click on Save to finish. 17.
ENVI Series: VTC-IR40-N 17.1. System Log System log file provides you the information about when and who access’ the contents of VITEKCameras such as HTTP file or CGI programs. In each line, log data consists of date, time, category, IP address, user ID. 17.2. Save Configuration VITEK cameras save the configurations after every step.
ENVI Series: VTC-IR40-N 17.3. Reboot It is recommended to reboot the system after making changes to the configuration. To reboot, click Reboot on Utilities menu. A screen will display to confirm a system reboot, click ok to continue. Windows Internet Explorer will ask to close the webpage, click Yes. 17.4. Factory Default When required to restore the configuration of a Camera to factory default conditions,Network configuration is not affected by this action. Click Factory Default on Utilities menu.
ENVI Series: VTC-IR40-N 17.5. System Update ** Is Highly Recommended to Use the IP Installer Program for This Process ** Once IP devices are searched and shown on the screen as functioning successfully, you can update the firmware of them using the“IP Installer” program. To do that, first check the firmware version of the device, which you can find on the IP Installer window.
ENVI Series: VTC-IR40-N In the above picture, the firmware version of this product is 4.14-01-ds while the latest firmware version available is 4.16-B0-ds-VI as you can see at Vitek’s homepage (http://www.vitekcctv.com/Downloads.asp). If you decide to update the firmware, first create a folder on your computer for the update firmware, than download the latest firmware to that folder. Then select the IP device to be updated on IP Installer window, then click Update Firmware button from the toolbar.
ENVI Series: VTC-IR40-N Note:Do not CLOSE window until completed, to avoid permanent damage to the camera.
ENVI Series: VTC-IR40-N 18. ENVI Series Viewer 18.1. Introduction ENVI Series Viewer is an ActiveX program for Internet Explorer web browser, which enable users to control video and audiofunctions of network video devices over the TCP/IP network. ENVI Series Viewer works with EN-V-R network video software, Vitek Network Video Servers, Network Video Recorders, and Network Cameras to show real-time live video images and enables users to control audio, Relay Output, and PTZ functions.
ENVI Series: VTC-IR40-N 19. Installing and Uninstalling 19.1. Installing ENVI Series Viewer Connect to the Vitek Camera/Server using Internet Explorer, and click Live View on the main page. Then ENVI Series Viewer will be automatically downloaded and installed. If an Internet connection is not available, it's possible to manually install the program file in advance (from supplied CD) and connect to the Vitek Camera / Server later. 19.1.1.
ENVI Series: VTC-IR40-N Click the Install ActiveX Control, and the pop-up window will be displayed as above. Click the Install button. Click “YES” to allow program to run. After the installation is successfully completed, ENVI Series Viewer window will be displayed.
ENVI Series: VTC-IR40-N 19.1.2. Manual Installation When an Internet connection is not available or having some difficulties, you can manuallyinstall from the supplied CD usingENVI Series Viewer program file.Execute the downloaded file, and you will see the ENVI Series Viewer Setup Wizard window as shown below. Click the Install button to start installing. The following window will be displayed during the installation. After installation is successfully completed, the following window will be displayed.
ENVI Series: VTC-IR40-N 19.2. Uninstalling ENVI Series Viewer There are two ways to uninstall ENVI Series Viewer program from your computer. Before uninstalling, close all the Internet Explorer windows. 19.2.1. Uninstalling with Program Menu Click Uninstall and the following window will be shown. Click the Yes button. If the uninstall is successful, the following window will be displayed. Click CLOSE to finish.
ENVI Series: VTC-IR40-N 19.2.2. Uninstalling on Control Panel Click Start button on the screen, then select the Control Panel. In the Control Panel window, double-click the Add or Remove Programs icon.
ENVI Series: VTC-IR40-N You will see the Currently installed programs list. Click ENVI Series / (Smart Viewer) button, You will see the Uninstall or change a program list. Click ENVI Series / (Smart Viewer) button, and then right click Uninstall /Changebutton. Then, it will start uninstalling the program. 20.
ENVI Series: VTC-IR40-N The appearance of ENVI Series Viewer window varies depending on what type of Vitek Server is connected (Network Video Server, Network Camera, or Network Video Recorder). • 20.1.
ENVI Series: VTC-IR40-N 20.2. Channel Control Bar Displays or hides live view video from channel 1 Displays or hides live view video from channel 2 Displays or hides live view video from ALL channels No Display 20.3. OSD Channels Buttons 20.3.1. Saving as Image File In ENVI Series Viewer, Live video currently displayed can be captured and saved as an image file either in JPEG or BMP format. Select the live view video you want saved, and click Snapshot button on OSD Channel Buttons.
ENVI Series: VTC-IR40-N 20.3.2. Saving as Video File In ENVI Series Viewer, Live video currently displayed can be captured and recorded as a video file in AVI format. Select a live view you want to save, and click RecAvi button on OSD ChannelButtons. Clicking it again will stop recording. Max duration is 10 minutes and recording will be stopped after 10 min if left un-clicked.
ENVI Series: VTC-IR40-N recorded to the SD Card by clicking this button. The recorded video can be viewed by Instant Playback feature of OSD Channel Buttons or by running ENVI Series Player program. To finish, click the icon again. Max duration is 1 minute and recording will be stopped after 1 minute. 20.3.4. Instant Playback For network cameras with local storage (SD Card), Instant Playback is supported. Clicking the Instant Playback button from the OSD menu will open the window below.
ENVI Series: VTC-IR40-N Set the beginning of video data. Instant playback will scan 1 min after this. Se the playback speed. Begin searching data Playback Reverse playback. 1 frame playback 1 frame reverse playback Pause Stop 20.4. Extended Features When you click the right mouse button on the Live View Window, a pop-up menu will appear for extended features as shown below. 20.4.1. Pausing Live Video Click the Pause button to stop and resume live view video. 20.4.2.
ENVI Series: VTC-IR40-N 20.4.3. Flip Control Flip Control: The horizontal view of the image can be changed using the (mirror) function. The vertical view of the image can be changed using the (flip) function. 21. EN-V-R: Introduction This User's manual explains how to set up EN-V-R software in your PC. EN-V-R is the integrated system software for video security applications, which runs on Microsoft’s Windows-based computers. Some of major features of EN-V-Rare listed below.
ENVI Series: VTC-IR40-N 22. Requirements for Installation 22.1. EN-V-R Versions EN-V-R is supplied to customers in different versions for each appropriate application. Users will need to choose the right versions for their needs.
ENVI Series: VTC-IR40-N 720P 1080P Intel Core i-5 -2500 3.0GB 1.5GB 720P Intel Core i-5 -2400S 2.0GB 1080P Intel Xeon X5590 Dual CPU 4.0GB Intel Core i-5 -2500 3.0GB 720P Intel Xeon X5550 Dual CPU 4.0GB 1080P Intel Xeon E7-4850 Dual CPU 6.0GB D1 64 channels 128 channels 1.5GB Intel Core i-5 661 D1 32 channels Intel Core i-5 460M D1 Intel Xeon X5687 Dual CPU 4.0GB 720P Intel Xeon X5690 Dual CPU 6.0GB 1080P Intel Xeon E7-4850 Dual CPU 6.
ENVI Series: VTC-IR40-N The default location for installation is C:\Program Files\Vitek. It is recommended to install in this folder, but if you want to change it to another location, click Browse button to choose a proper path. Now click Install button. You will see the progress of copying install files to the hard drive as shown below, once is completed click on NEXT. Click Finish to complete the Installation.
ENVI Series: VTC-IR40-N After installing EN-V-R programfor the first time, it needs to be configured before use, so it automatically executes the configuration program, which is called EN-V-R Configurator. Enter the proper Admin Password. The default password is root. The following screen will be displayed, click OK to continue. Now you will see EN-V-R Configurator window on the screen.
ENVI Series: VTC-IR40-N For more information about the EN-V-R Configurator program, refer toSection 26.Starting EN-V-R Configuratoron page 121. 24. Uninstalling EN-V-R 24.1. Closing Active EN-V-R If you need to uninstall EN-V-R, first you need to make sure EN-V-R program is not running on your computer by checking the system icon. As you see on the following picture, you can easily find out if ENV-R service running.
ENVI Series: VTC-IR40-N Then the EN-V-R icon disappears, and you know that EN-V-R is no longer running on your computer. Now you’re ready to start uninstalling. 24.2. Executing Uninstaller To start uninstalling, click Start >All Programs >Vitek>EN-V-R>Uninstall. When the following window appears, click YES button. The progress of uninstalling is displayed. After all the install files are deleted, the following window will be displayed.
ENVI Series: VTC-IR40-N 25. Components of EN-V-R Program EN-V-R consists of three programs, (EN-V-R Service, EN-V-R Configurator, and EN-V-R Controller ). 25.1. EN-V-R Configurator EN-V-R Configurator is used to set up various parameters and conditions of EN-V-R Service. Users can register, modify, and delete IP devices and users with this program. It also provides configuring tools for recording, alarm, event, and other functions. 25.2.
ENVI Series: VTC-IR40-N 26. Starting EN-V-R Configurator EN-V-R Configurator starts automatically right after installation is completed; you may also click the EN-VR icon on the Windows desktop. If EN-V-R program is already running in background, you may also select the EN-V-R icon on the system tray by clicking right button of the mouse. You may encounter the security window as below. Click Yes button to continue. Once EN-V-R program starts, a log-in window will be displayed as below.
ENVI Series: VTC-IR40-N Now EN-V-R Configurator window will be displayed. 27. Quick Start Guide EN-V-R is full-functioning Network Video Recorder software that runs on your PC. When started for the first time after EN-V-R is installed, there is no IP devices connected. To add a camera to the EN-V-R you must register the camera first. Then EN-V-R knows what IP devices they are, how to connect to them, and how to use them. That way, you will be able to control EN-V-R for recording, live viewing, etc. 27.1.
ENVI Series: VTC-IR40-N Items Descriptions A Main Toolbar Frequently-used menu items are shown on this toolbar. B Configuration Menu tree Configurable categories are shown as a menu tree style. C Configuration Menu Description Descriptions and usages of the selected category are displayed. D Sub-Menu Toolbar Menu items for the selected category are shown. (Note: This toolbar is displayed only when any top menu item is selected from the menu tree.
ENVI Series: VTC-IR40-N You are now given a choice to register the IP devices by “search and register or manually”. To make it easy, choose Search and register IP-Device in this stage, and click Next button. On the following window,click Scan button. The searching for IP devices is started. As the detected IP devices are being listed. Wait until searching is finished. If you click Cancel button in the middle of searching, the EN-V-R will retain only the IP devices found until that moment.
ENVI Series: VTC-IR40-N 27.3. Registering IP Devices After scanning is finished, you have a list of IP devices found on your network. Next step is registering them. Double click the IP device you want to register or you may highlight it and then click Register button. In this example, the first one is chosen to register. The next window shows up and it’s for entering the network parameters and camera resolutions of the IP device you’ve chosen. You may need to enter the Login ID and Password here.
ENVI Series: VTC-IR40-N Click on Save after configuring IP device (camera) Click Apply after registering one or more IP devices (cameras).The image below represents the configurator with multiple IP devices registered.
ENVI Series: VTC-IR40-N After clicking Apply, the program will ask you to confirm it.Then click OK EN-V-R service is being stopped momentarily, and then it will start running again. 27.4. Viewing Live Video Once the network and cameras are set up, it is necessary to check if EN-V-R is functioning by viewing the live video from those devices. To view the EN-V-R home page, click the Go NVR Home button on the main toolbar. Below is an image of the EN-V-R home page.
ENVI Series: VTC-IR40-N Click Live View on top right part of the window to see the live video from registered IP devices (cameras) If this is the first time you are using VitekLive View feature, the web browser may ask you to allow installing of an ActiveX program. Click Install to continue. In some cases there is no response from the web browser, you may need to install the ActiveX manually by clickingManualDownload. When you see the following security warning, click Install.
ENVI Series: VTC-IR40-N 27.5. Recording Video The essential feature of EN-V-R is recording the video from IP devices. Before starting the recording, it is required to prepare the hard drive of your PC where EN-V-R program is running. Click Disk Quota on the Menu tree. The hard drive will be ready to start recording video after the progress window is done counting drives. It shows the target drive (s), total capacity, available size and quota for recording.
ENVI Series: VTC-IR40-N Possible Maximum Quota (the available of free space on your HDD) Possible Minimum Quota (the minimum amount required) Set Quota (desired amount of HDD to be use for recording) To set up the recording feature, select an IP device from the Menu tree on the left pane. The device information will be shown on the right pane. Click the button for recording configuration on the sub-menu Toolbar as shown below. Now you will see Configure Recording Condition window as below.
ENVI Series: VTC-IR40-N The recording feature is already enabled and recording conditions are configured in default settings. In the example shown above, you can see that Camera 1 of Device 0 will record video only when motion is detected. ClickOK to use this Recording Conditioned.
ENVI Series: VTC-IR40-N Now that the configuration is done, you need to start the EN-V-R service program. Select Start > All Programs >Vitek>smart NVR>Smart NVR controller. You will find the EN-V-R icon on the system tray, which is located right, bottom part of the Windows desktop. Move the cursor over the icon, and right click. The following pop-up menu will show.
ENVI Series: VTC-IR40-N You can find out from this window that the service is running at that moment. If not, click Start Service button to run. Once EN-V-R service is started, the video sent from the configured camera will be recorded according to the recording condition. 28. ENVI Smart Player 28.1.
ENVI Series: VTC-IR40-N 28.3. System Requirement for PC For best quality and performance, your computer needs to meet the minimum requirement. OS: Microsoft Windows XP Pro, Windows 7 Pro, Windows 8 PC CPU: Intel Pentium 4, 2 GHz (Dual-Core or faster is recommended) System RAM: 2GB Video Card: 256MB Ram, 1024x768 Resolution 100 Mbps Network Adaptor 29. Installing and Uninstalling 29.1.
ENVI Series: VTC-IR40-N After the installation is successfully completed, Smart Player window will be displayed. 29.1.1. Manual Installation When an Internet connection is not available or having some difficulties, you can manually download and install the Smart Player program file prior to setup, visit http://www.vitekcctv.com/Downloads.asp. You may also install from the provided CD. Execute the downloaded file, and you will see the Smart Player Setup Wizard window. Click Run to start installing.
ENVI Series: VTC-IR40-N After installation is successfully completed, the following window will be displayed. Click Finish. 29.2. Uninstalling Smart Player Before uninstalling, close all the Internet Explorer windows. 29.2.1. Uninstalling on Program Menu Click Uninstall and the following window will be shown. Click the Yes button.
ENVI Series: VTC-IR40-N Live View & Play Back To live view and play back your cameras, go to Start menu, All Programs, Vitek Folder, Click on Smart NVR Controller, as shown below. Look for icon on right side of taskbar as shown below (windows XP and windows 8 might show it different). Right click icon. The following window will display. Click on Open Smart NVR Controller.
ENVI Series: VTC-IR40-N Click on Start Service to run the program. Click on Go Home to view Smart Player Home Page Click on Live View The following screen will be display were you can configure your live view.
ENVI Series: VTC-IR40-N Server Control Bar Allows you to view cameras / servers that are registered in the system.
ENVI Series: VTC-IR40-N In order to view video, cameras must be assigned to a group, in this section you create groups with cameras you want to view. Create Group In order to create a group in Group Control Bar, right click on Group, another window will appear then select New. The following window will be displayed. Type in the group name, check “Circulation” to allow sequencing, input dwell time for “Circulation” and click OK. A new group with the assigned name will be created as shown below.
ENVI Series: VTC-IR40-N PTZ control Bar In this section you will be able to control PTZ’s connected to the system. Audio Control Bar Controls Speaker and Mic volume. When audio is available click on Connect and adjust speaker and mic levels, when done click Disconnect.
ENVI Series: VTC-IR40-N Full/Normal Screen Select full screen as seen below, to return to normal press Escon your keyboard. Group Circulation Start sequencing between groups.
ENVI Series: VTC-IR40-N Layout settings You can change the screen layout between 1,2,4, etc. Image in Original Size This allows for digital zoom.
ENVI Series: VTC-IR40-N Draw Image by Maintaining Aspect Ratio Maintains the aspect ratio of the camera Draw Image by Filling the Screen 144
ENVI Series: VTC-IR40-N Enhanced Draw Mode On/Off. Enhance image for a better reproduction.
ENVI Series: VTC-IR40-N About Smart Viewer You can see the status of the Smart Viewer 30.
ENVI Series: VTC-IR40-N 30.1. Main Window View Note:The appearance of Smart Player window may vary depending on version and type of Vitek device you’re using. This user’s manual is based on general display screen. Server Control BarA Allows you to view cameras / servers that are registered in the system.
ENVI Series: VTC-IR40-N Group Control BarB You can compose a new group by dragging&dropping servers, modules, and cameras into a group.Grouping provides search function of recorded video from cameras. Playback Control Users can use this bar for functions such as forward/reverse play, previous Bar C frame, next frame, pause, stop, playback speed. Control Tool BarD Time Line Control BarE Display screenF 30.2. Users can change search modebetween calendar, condition, and data.
ENVI Series: VTC-IR40-N The following window will be displayed. Type in the group name and click OK. A new group with the assigned name will be created as shown below. To add a camera to the new group, drag and drop from the server tree to the newly created group.
ENVI Series: VTC-IR40-N 31. Searching Video Make sure you have recorded video on the calendar (recorded video shows in red). There are three choices in searching recorded video - Day Search, Condition Search, and Data Search. Make sure that Camera / Server Connection and Creating Group have been performed before you search recorded video. 31.1. Searching Video To search and playback video, Smart Player requires one or more groups to exist.
ENVI Series: VTC-IR40-N 31.2.1. Search Mode By clicking a date in red on the calendar, the time frame recorded is shown. 31.2.2. GO to Time Position To go to specific time click on “Go to time position” than input time and click search. 31.3. Condition Search Mode In this mode, you can search for video on the basis of combination of 3 different conditions, which are Time, Motion, and Sensor.
ENVI Series: VTC-IR40-N video will start playing back right after searching is completed. 31.3.1. Advanced Search Mode In Advance Search Mode you can select which conditions to search from (Time, Event, etc) First, select Time checkbox, and choose the desired time frame (Start date and time ~ End date and time), and then click Add Condition button to add to Search Condition. Now select Event checkbox, and choose Camera 1 from Motion, and then click Add Condition button to add to Search Condition.
ENVI Series: VTC-IR40-N Now that all the conditions have been configured, click Search button to start searching. Any video data which meets at least one of the conditions in Search Condition list will be shown as the results. 32.
ENVI Series: VTC-IR40-N Back to Previous Frame Go to Next Frame Playback Speed Control Player Path Control (only for condition search mode) 33. Extra Features 33.1. Window Control Users canopen or close control windows. 33.2. Recording Period You can view the starting and ending date of a recorded channel. Record time is displayed as shown below.
ENVI Series: VTC-IR40-N 33.3. Backup There are two backup formats IDX and AVI. .IDX Default video file format used by Vitek .AVI Video file format supported by Microsoft Windows When the Backup button is clicked, the following window is displayed as below. Select Camera Backup Period Check the camera to backup. For AVI backup, only one camera is permitted. For FJP, IDX, multiple backup is allowed. Select the time frame (Start date and time ~ End date and time) to backup.
ENVI Series: VTC-IR40-N After searching is finished, backup operation will start. When backup is completed, the following window will appear. Click OK button. Note: For AVI file backup, only one camera is allowed. For IDX backup, multiple cameras are allowed. 33.4. Snapshot Choose the camera currently being played or paused, click Snapshot button. Then a snapshot file will be saved in a designated path.
ENVI Series: VTC-IR40-N The below picture is a result of snapshot from the above window. 33.5. Print Choose the camera currently being played or paused, then click Print button. Then the image of the selected camera will be sent to your default printer. 33.6. Ratio Display You have three options to view videos, which are Original, Ratio, and Stretch.
ENVI Series: VTC-IR40-N 34. EN-V-R Configuration A 34.1. System, Network Configuration General system and network properties of EN-V-R program can be set up in this section. To start, select System, Network Configuration from the menu list.
ENVI Series: VTC-IR40-N Items Descriptions System Name Setting Enter the system's name. Set up Admin password Modify the password for Admin. Access Control Configure the access privileges of users. HTTP Port Assign Assign an HTTP Port for EN-V-R Service. Configure IP-CCTV DNS Configure IP-CCTV DNS for EN-V-R Service 34.1.1. Configuring System name To name the system, click configuring system name, the following window will be displayed. Change the name as desired.
ENVI Series: VTC-IR40-N Items Descriptions System name Type in a System name. OK Click this button to apply the entered System Name. Cancel Click this button to discard the configured System name. 34.1.2. System, Network Configuration - Admin password To assign Password for the admin, click System, Network Configuration on the menu tree. Click configure admin password Items Descriptions Current password Enter the Current password. New password Enter a new password to use.
ENVI Series: VTC-IR40-N Items Descriptions Full Access Set Full Access for the user. Anyone can connect to the EN-V-R without authentication, and be allowed live view, audio, PTZ, playback. Limited Access Set Limited Access for the user. Only the users with proper permission to the camera can access it. OK Click this button to apply the change. Cancel Click this button to discard the change. 34.1.4.
ENVI Series: VTC-IR40-N Items Descriptions Service Set to use IP CCT DNS or not. DNS Server IP Vitek IP CCTV DNS address already entered. Go Server Directs to Vitek IP CCTV DNS server MAC MAC address of EN-V-R already entered Product Key Product Key of EN-V-R already entered External Port Enter an external HTTP Port to use for IP CCTV DNS service. (Default is 80) Register verify Click to test the connection with IP CCTV DNS server after setting is done in IP CCTV DNS server.
ENVI Series: VTC-IR40-N Fill out the requested information as shown below and click on Apply. The following screen will confirm that your Membership has been completed successfully, that click OK. You will be brought back to the main page of the IPCCTVDNS website; in this case you need to Login with the information previously created.
ENVI Series: VTC-IR40-N To register your first product, click on Product Registrationas shown below. Enter the requested information (The name of your camera, the Mac Address and product Key) as shown below. Note that the Mac Address and the product Key will be available under the Network Configuration>> IPCCTV DNS setupin thecamera menu. Please see image below.
ENVI Series: VTC-IR40-N A window will pop up confirming that your product has been registered successfully, click on OK. You will be directed to the Product List page where you will be able to see your recent camera registration. By clicking the Detail Information tab you will be allow edit DDNS Host Name Click Edit to change the DDNS Host Name. Type in desired host name than click Apply.
ENVI Series: VTC-IR40-N A window will pop up asking if you really want to apply the new configurations, to continue click OK. A window will pop up confirming that the product information has been modified successfully, click OK. Click under Product List to view your changes Your camera with the new DDNS Host name will be displayed.
ENVI Series: VTC-IR40-N Your camera is now registered and ready for use. 36. IP-Device Registration You will see how to manage IP devices in this section, which includes registering, modifying, and deleting IP devices. To start managing IP devices, select IP-Device, Camera Management from the menu list.
ENVI Series: VTC-IR40-N 36.1. Items Descriptions A IP-Device Manual Registration Register IP-Devices manually by users. B IP-Device Automatic Registration Scan and register IP-Devices automatically by the program. C IP-Device Modification Modify the information of registered IP-Devices. D IP-Device Deletion Delete IP-Devices previously registered. E IP-Device Homepage Go to the homepage of the IP-Device.
ENVI Series: VTC-IR40-N A Item Description IP-Device ID Select the IP-Device ID to register. Select the Vendor name of the IP-Device to register. Click the pull-down list, and choose a proper vendor name from the list. B Vendor C Model Select the total number of channels (streams) the IP device has. Click the pull-down list, and choose proper one from the list.
ENVI Series: VTC-IR40-N D Name Type in the name of the IP-Device. E IP Address Type in the IP Address to use with the IP-Device. IPCCTVDNS or URL addresses are also supported. (If Input IP Address Range box is checked, then the starting address of the range will be selected.) F Input IP Address Range Enter the last IP address of the range. G Getting Information from IP-Device Check this box if the information from IP-Device needs to be acquired. H VS Module ID Select the VS Module ID.
ENVI Series: VTC-IR40-N Items Descriptions A IP-Device list This list shows the IP devices found during the scan process. If you need to select multiple IP devices at the same time, drag your mouse over the devices or keep pressing CTRL or SHIFT key while clicking the IP devices. B Clear Clear the scanned IP Devices from the list. C Scan Start scanning for IP Devices on the network. D Go Home Go to the home page of the IP device selected from the list.
ENVI Series: VTC-IR40-N Items Descriptions A Resolution Description Descriptions of the image resolution modes in the IP-Device list.(R1, R2, R3, R4, R5, R6, R7, R8, R9, R10) B PTZ Install Description Descriptions of the PTZ numbers in the IP-Device list. (P1, P2, P3, P4) C IP-Device list IP-Device list to select from. D Apply to All Click this button to copy the information of a selected IP-Device to all other devices.(Only Model, Login ID, and Login Password will be copied.
ENVI Series: VTC-IR40-N Items Descriptions A IP-Device ID IP-Device ID is displayed. (not allowed to modify) B Vendor Select the Vendor of the device. C Model Select how many channels the device support. D Name Change the Name as required. E IP Address Enter the IP Address to use with the selected device. F Input IP Address Range (not allowed to modify) G Getting Information from IP-Device (not allowed to modify) H VS Module ID Select the VS Module ID.
ENVI Series: VTC-IR40-N Q 36.3. Cancel Click this button to discard the changed values. IP-DeviceDeletion To delete a registered IP-Device, click IP-Device, Camera Management on the menu tree in the left pane. Then select an IP device to be deleted from the list. Click Remove IP-Device registration 36.4. IP-DeviceHomepage To go to the home page of an IP-Device, click the IP-Device, Camera Management on the menu tree. Then select the IP device. Click Go to IP-Device homepage 36.5.
ENVI Series: VTC-IR40-N A Camera Information Configure Information of the selected camera. B Resolution and Quality Choose the resolution and quality of cameras. C Recording Conditions Set up recording conditions. D Alarm and Map service settings Configure Alarm and Map service functions. 36.5.1. Configure Camera Name and Information From the configuration list, select a camera to be assigned with a name.
ENVI Series: VTC-IR40-N The below image will be display, enter name (F), then click Apply to camera(H), then OK. Items Descriptions A,B,C,D Camera Selection Select one or more cameras for name assignment by clicking buttons. E Unselect All Clear the device list which shows the selected cameras. F Name Type in a camera name. G Clear Clear the camera name field. H Apply to Camera Apply the changed camera name to the system. I OK Click this button to confirm the change and close the window.
ENVI Series: VTC-IR40-N Items Descriptions A,B,C,D Camera Selection Select one or more cameras by clicking buttons. E Unselect All Clear the device list which shows the selected cameras. F Resolution Select the video resolution. G Quality Select the video quality. H Apply to Camera Apply the selected video resolution and quality to the system. I Go Home Go to the homepage of the product. J Close Close and exit the window. 36.5.3.
ENVI Series: VTC-IR40-N The below image is where you adjust the recording parameters. Item Description A,B,C,D Camera Selection Select one or more cameras by clicking buttons. E Unselect All Clear the device list which shows the selected cameras. F Condition List Define the condition for recording to be started. G Condition to use Decide whether to use the defined condition or not. H Condition Mode Select the condition mode for recording. I Scheduling Set up the schedule for recording.
ENVI Series: VTC-IR40-N N Pre Alarm Images Select pre-alarm images. O Pre Alarm Speed Select pre-alarm speed. P Post Alarm Images Select post-alarm images. Q Post Alarm Speed Select post-alarm speed R OK Click this button to confirm the change and exit the window. S Cancel Click this button to cancel the all the changed made in this session. To setup recording, first click camera under Condition list(F).
ENVI Series: VTC-IR40-N 36.5.4.
ENVI Series: VTC-IR40-N A,B,C,D Camera Selection Select one or more cameras by clicking buttons. E Unselect All Clear the device list which shows the selected cameras. F Alarm Service Setup Put check marks on alarm types to use. G Event Service Setup Put check marks on event types to use. H Apply to Camera Click this button to apply the changes to the camera. I OK Click this button to confirm the change and exit the window.
ENVI Series: VTC-IR40-N 36.6.1. User Registration To register a new user, click the 1'st button on the tool bar in the sub-menu toolbar. Items Descriptions A User ID Enter a new User ID to register. B Password Enter the Password for the new user. C Confirm password Enter the same Password for confirmation. D Name Enter the name of the new user to be registered. E System resource access permission Choose the level of permission for System resource access.
ENVI Series: VTC-IR40-N To modify a user's information, select the users name than click the second button on the submenutoolbar. The User Registration window will come up on the screen, make the necessary changes and click OK . 36.6.3. UserDeletion To delete an existing user, select the user name than click Remove Registered user account, another screen will pop up confirming to proceed with deletion, click OK to proceed . 36.7. Disk Setup 36.7.1.
ENVI Series: VTC-IR40-N device list. The following window will be displayed. Item Description A Use HDD Decide whether this HDD is to be used. B Possible Maximum Quota Display Possible maximum quota on this HDD. C Possible Minimum Quota Display Possible minimum quota on this HDD. D Set Quota Enter the desired size of disk quota for recording. E OK Click to apply the configured disk quota. F Cancel Click to cancel the disk quota configuration.
ENVI Series: VTC-IR40-N Items Descriptions A Disk Circulation Setup Configure disk circulation type. B Disk Usage Report Setup Configure email address for reporting. Click the Disk Circulation in the list. The following window will be displayed. Item Description A Use circulation Select this if disk circulation will be used. B Not use circulation Select this if disk circulation will not be used. C Use expired duration Decide whether the expiration will be used for recording.
ENVI Series: VTC-IR40-N Item Description A Use to report HDD usage Choose whether to Enable or Disable the report service. B Report HDD space When disk circulation is not used, select the HDD size when it will be reported by email. C Periodic report Define when Periodic reports will be sent. D OK Click to apply the Email report settings. E Cancel Click to cancel Email report configuration. 36.8. Utilities Select Utilities from the menu tree.
ENVI Series: VTC-IR40-N email account for mail service Item Description A Service Decide whether to report HDD usage by email or not. B SMTP server Enter the address of SMTP server for sending email. C Authentication Decide whether to use Authentication. D Email user id Enter the sender's id for email account. E Email user password Enter the password of the sender’s email account. F Sender email Enter the Sender's email address.
ENVI Series: VTC-IR40-N Items Descriptions A About program Show the information about the EN-V-R running. B System Resource Displays the PC's system resource information. C OK Click this button to close the Window. 37. Using EN-V-R Controller To open EN-V-R controller,click Start >All Programs>Vitek>SMART NVR Controller. Smart NRV controller will be on the lower right part of the system tray. Then right click the icon a subwindow will display, click on Open Smart NVR Controller.
ENVI Series: VTC-IR40-N Items Descriptions A Current Service State Shows whether EN-V-R Service is running or stopped. B Start Service Click this button to start EN-V-R Service when it’s stopped. C Stop Service Click this button to stop EN-V-R Service when it’s running. D Refresh Refresh the Screen. E Go Home Go to the EN-V-R’s built-in webpage. F Close Close the EN-V-R Controller window. 38. Connecting to EN-V-R 38.1.
ENVI Series: VTC-IR40-N After you successfully connecting to the EN-V-R homepage, you will see the following window. Items Descriptions A Home Go to EN-V-R’s homepage. B Live View Click this button to execute Live View program. You can use various features such as live view, audio transmission, PTZ control, unconditional recording, etc. C Player Click this button to search, record, and back up the video data sent from IP devices registered in EN-V-R. 38.2.
ENVI Series: VTC-IR40-N In case that the HTTP port for EN-V-R is not 80 (default), the port number should be entered together with the IP address.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. Digital recording and storage products are also warranted for 3 years except for the hard drives which carry their own independent factory warranty from the hard drive manufacturer.
CLASS A DIGITAL DEVICE (INDUSTRIAL & COMMERCIAL ENVIRONMENT) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to CE and FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
