Quick Start Guide

1
2
43
VITEK
VITEK
VTC-TNB8X4MS
QUICK START GUIDE
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
Components and Accessories
Cable Connections
Overview
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera.
Weather Resistant Network Coupler
2. Route the cables and connect the relevant cables, use the rubber
plug to fill the gap of the mounting base. Then secure the mounting
base to the ceiling or wall with screws.
3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then
tighten the mount lock to secure the viewing angle adjustments.
Camera
Plastic
plug ×4
Drill template
Screwdriver
Rubber
plug
4 tapping screws
1
3
4
5
6
7
2
ALA
RM
4 3 2 1
R 4
85
S
+
8
9
1. Ethernet Connector
2. Audio Input (MIC)
3. Audio Output (HP)
4. Alarm Input/Output
5. RS485
Security cap
Ground
AL
A
R
M
4 3 2 1
R 4
8
5
S
+
1--A L M -C OM
2--A L M -O P E N
3--A L M -I NA
4--A L M -G ND
R S 485T +
R S 485T -
6. Power Connector
7. Ground
8. Reset
9. Micro SD Slot
First connect the Waterproof
Cap to an Ethernet patch
cable, then connect the
cameras ethernet adaptor. If
not powering the camera with
PoE, also connect the power
Cable to an approved 12VDC
Power Supply.
C onnecting Alarm Input/O utput
A l ar m
P ower S our ce
IPC
A L A R M -C O M
A L A R M -O P E N
A lar m I nput
A lar m O utput
+
+
-
-
Sensor
IPC
A L A R M -I N
A L A R M -G ND
3
4
1
2
1. Loosen the nut from the Weather Resistant Network Coupler
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
1. Open the cover of the camera and insert a micro SD card. Then replace the cover
with screws (keep the unit at while inserting SD card and replacing cover).
Insert a micro
SD card
Cover
2. Using the template, drill
screw holes and the cable
hole (if routing cable through
the wall or ceiling).
∅4.50mm
90.23mm
90.22mm
1.77”
3.55”
3.55”
Mounting base
Rubber plug
Fixed screws
Rotate : 90
Pan
: 18
0
Tilt: 90
°
°
°
Mounting the Camera wtih a J-Box
1. Mount the junction box to the wall or ceiling with screws.
2. Route and connect the relevant cables.
3. Fix the camera to the junction box with screws.
Transcendent 8 MegaPixel
H.265 Indoor / Outdoor
Multi-Sensor (1/2.8” 2MP)
180° Panoramic IP Camera
• Four 1/2.8” 2MP Progressive Scan CMOS image sensors
• Resolution of up to 4096 x 1800
• 4 x 3.3mm Fixed Lens
• 1s~1/10,000s; Auto/Manual Electronic Shutter
• 8 IR LEDs with 65’ IR Range with 180° Array
• 120dB Super Wide Dynamic Range (WDR)
• Intelligent Analytics including Object Removal/Museum Search,
Line Crossing, and Area Intrusion Detection
• True Mechanical Day/Night function by ICR
• XD-DNR (2D & 3D-DNR) Noise Reduction
• Field of View Capacity: Pan (180°), Tilt (80°)
• H.265/H.264/MJPEG Triple Streaming
• Single IP Address Input Required
• Secondary Video Output (CVBS)
• Remote View via CMS, IE, iOS & Android Apps
• ONVIF Compliant
• MicroSD memory card slot for Local recording supporting up to
128GB MicroSDXC cards
• IP67 Weather Resistance / IK10 Impact
• Two-way Audio
• 12VDC & PoE (Power over Ethernet) Operation
• VT-TJB010 J-Box Included