Side Rail Cutter BT900SR/ BT900SRIND/ OWNER’S MANUAL Read and understand all instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CONTENTS PAGE 1 – SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 – OPERATOR’S INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 RANGE OF APPLICATIONS AND USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 – SPECIFICATION BT900SRIND Mains voltage (Volt): 110 V~ 50Hz Motor capacity: 1100W Insulation class: B House protection class: IP54 No load speed (/min): 3400 Max. Cutting Depth: 35mm Maximum Cutting Length: 760mm Diamond blade size: Ø200 X Ø22.23mm(bore) Table size (no extension): 807 X 460mm Net/Gross weight: 75/85KGS BT900SR 240V~50Hz 900W B IP54 2850 35m 760mm Ø200 X Ø22.
DIRECTION OF BLADE Please make sure the diamond blade always towards the same direction as the arrow which is molded on the blade guard. GENERAL SAFETY RULES WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury including the following. Read all these instructions before attempting to operate this product and save these instructions. 1. Keep work area clear - Cluttered areas and benches invite injuries. 2.
18. Check damaged parts - Before further use of tool, it should be carefully checked to determine that it will operate properly and perform its intended function. - Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. - A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual.
• • • cut material from around the blade area. Never allow the diamond blade to run dry. Failure to keep the water tray topped up will result in possible over-heating of the diamond. Do not expose to rain. Wear suitable protective equipment. Eye Protection shall be worn • • • • • • • • • Ear protection shall be worn Caution, risk of cutting Hand protection shall be worn Adopt a working position to the left of the diamond blade.
mains voltage. Always keep away the mains lead from moving parts of the machine. Do not apply side-pressure to the diamond blade. It can break the blade and cause the danger. 5. Un-plug before you open the machine. Warning: before any operation with this machine, please confirm sufficient local lighting has been provided. • IMMEDIATELY SWITCH OFF THE MACHINE IN CASE OF: 1. Malfunction of the mains plug, socket or damaged cables. 2. Broken switch. 3. Smoke or smell caused by scorched insulation. 3. 4.
Fig. 5 Fig. 6 C. MOVING THE MACHINE 1. 2. For long distance move, fold the machine to move. For short distance move: lift the machine and drag the wheels to make them stand up against ground. (Fig. 7, 8, 9) Note: While the machine is in use, make sure the wheels are moved back to the locked position. (Fig. 10) Fig. 7 Fig. 8 Fig. 9 Fig. 10 3. Adjust the screw on one foot to keep balance among the feet (Fig. 11). Fig. 11 Fig. 12 D. TO FILL AND DRAIN THE WATER TRAY 1.
flow of water over the en¬tire Saw Blade while cutting. Never cut anything if the water flow is not continuous. 2. Prior to draining the Water Tray, first place a large bucket under the Drain Plug. Remove the Drain Plug located at the bottom of the Water Tray. Once drained, replace the Drain Plug. NOTE: You may also pull out the Water Tray from the Tile Saw and pour out the water. 3. After draining the water, rinse Tray to remove any silt. NOTE: Before moving the machine, the water tray should be drained.
Fig. 16 Fig. 19 Fig. 17 Fig. 20 Fig. 18 Fig. 21 Fig. 22 H. MAKING A 45˚ BEVEL CUT 1. Pull out the lock bar and raise up the cutting block. (Fig. 17). 2. Tilt the cutting block at 45˚ and tighten the lock knob (Fig. 18). 3. Following the same procedure as straight cut to cut the tile/stone. (Fig. 19) I. MAKING A PLUNGE CUT 1. Pull out the lock bar and raise the cut unit. (Fig. 20) 2. Tighten the lock knob. (Fig. 21) 3.
2. REPLACING THE DIAMOND Blade a. To disconnect the water supply, press the blue ring and pull out the Water Supply Tube from the Inlet Connection on the Blade Guard (Fig. 23). b. Remove the blade guard by removing the 2 screws (Fig. 24). c. Use the hexagonal wrench to hold the blade nut and use the spanner wrench provided to hold the shaft. Turn clockwise to unscrew and remove the Blade Securing Nut. Then, remove the Outside Flange (Fig. 25). d.
2. Replace the foam filter To replace the foam filter, remove the intake cover, then take out of the foam filter and put into a new one. Note: Only an authorized person of service center should perform repairs! 7 – TROUBLE SHOOTING Below we have listed a number of possible causes and corresponding solutions in case the machine dose not function as it should: Problem Possible Solution Stone/Tile Saw does 1. Make sure to press the “-“ button on the Power Switch. not turn on 2.
