TWIN BUNK BED Color: Espresso White Congratulations on your latest furniture purchase! Furniture has been developed with quality, convenience and style in mind. We trust it will provide you with many years of exceptional comfort and service. Before beginning assembly, we encourage you to familiarize yourself with your new furniture piece by taking a few minutes to go through this booklet. It contains important information on our warranty and care tips to keep your furniture looking as good as new.
CUSTOMER SERVICE If you are missing parts or have any questions about this product, contact our customer service representative first! You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part. WARNING * STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT LIMITED TO HOOKS, BELTS AND JUMP ROPES.
NOTES READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP OF * INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN INJURY. * CAUTION: ADULT ASSEMBLY REQUIRED * MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A SMOOTH SOFT SURFACE. * * * * * ASSEMBLY WILL REQUIRE TWO PEOPLE. MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
TWIN BUNK BED HARDWARE LIST 2 1 ∅1/4" x 100mm ∅6.5mm x 48mm JOINT CONNECTOR (4mm HEX HEAD) 16 PCS WOOD JOINT CONNECTOR (4mm HEX HEAD) 14 PCS 4 3 ∅6.5mm x ∅4mm x 35mm WOOD JOINT CONNECTOR (4mm HEX HEAD) 22 PCS 5 FLAT HEAD WOOD SCREW 24 PCS 6 ∅4mm x 30mm FLAT HEAD WOOD SCREW 6 PCS 7 ∅19mm x 95mm WOOD DOWEL 4 PCS 8 ∅10mm x 50mm ∅11.
TWIN BUNK BED PARTS LIST A B TOP POST 2 PCS D C TOP POST 1 PC E BOTTOM POST 2 PCS TOP POST 1 PC F BOTTOM POST 2 PCS TOP HEADBOARD TOP CROSS -2 PCS
TWIN BUNK BED PARTS LIST G H HEADBOARD BOTTOM CROSS 4 PCS J I TOP SIDE RAIL (WITH 3 HOLES) 1 PC K TOP SIDE RAIL (WITH 1 HOLE) 1 PC M L LONG GUARDRAIL 2 PCS O SHORT GUARDRAIL 2 PCS Q SHORT LADDER END 1 PC SLAT 12 PCS BOTTOM SIDE RAIL (WITH NO HOLE) 1 PC N P BOTTOM SIDE RAIL (WITH 2 HOLES) 1 PC LONG LADDER END 1 PC R LADDER STEP 4 PCS GUARDRAIL LEG 2 PCS
TWIN BUNK BED PARTS LIST S T U TOP HEADBOARD SLAT 8 PCS V SLAT 4 PCS W TOP HEADBOARD SLAT 4 PCS Y BOTTOM HEADBOARD PANEL 2 PCS TOP HEADBOARD PANEL 2 PCS Z BOTTOM HEADBOARD TOP CROSS- 2 PCS BOTTOM HEADBOARD SLAT 8 PCS X BOTTOM HEADBOARD SLAT 4 PCS
TWIN BUNK BED STEP 1 One of the headboard top crosses (F) has a label on it. Do not use it in this step. Insert stoppers (10) into headboard bottom cross (G) as shown above. Insert top headboard slats (S & V) and top headboard panel (W) to top headboard bottom cross (G) and push down until firmly in place. Attach the headboard top cross (F) on the top headboard slats (S & V) and headboard panel (W). Insert wood dowels (7) into each end of headboard top cross (F) and bottom cross (G).
TWIN BUNK BED STEP 2 Repeat the previous step to assemble the remaining three sets of headboards. Be sure to pair the bottom posts (D) and (E) for one pair; (E) and (D) for another; and the top posts (C) and (A) for the last pair. NOTE: Be sure to use headboard top cross (F) with label attached to it between top posts (A) and (C). See illustration for label orientation.
TWIN BUNK BED 1 1 8 8 8 K 8 K 8 I I Holes Holes 8 8 8 1 1 9 9 STEP 3 Attach the two headboards with bottom posts (D and E) to bottom side rails (I and K) using joint connectors (1) and barrel nuts (8) as shown. Use Allen key (9) to tighten to joint connectors. Note: This is the lower bunk.
TWIN BUNK BED M M 3 M STEP 4 Insert wood dowels (7) into each end of the long guardrails (M). Attach two long guardrails (M) and two top side rails (H and J) to top posts (A and B) & (A and C) as shown. Fasten top side rails (H and J) with joint connectors (1) and barrel nuts (8). Fasten long guardrails (M) with wood joint connectors (3). Use Hex key (9) to tighten all joint connectors. This is the upper bunk.
TWIN BUNK BED STEP 5 Insert two slats (T) onto the center slots of the bottom side rails (I and K) of the bottom bunk as shown. NOTE: Once inserted, there should be three empty spaces left on each side.
TWIN BUNK BED STEP 6 Insert slats (L) into the remaining holes on the bottom side rails (I and K) on the lower bunk. Secure slats (L) to the bottom side rails (I and K) with flat head wood screws (4), using a phillips head screw driver (not included). Repeat step 5 and 6 to attach slats (T and L) to the upper bunk. NOTE: Slats (T and L) will be placed between two wooden blocks.
TWIN BUNK BED M M M 3 3 3 7 7 7 A A A 6 6 6 N N N B R B R B R R R R 6 6 6 5 5 5 5 5 5 J J J H H H C C C K K K I I I STEP 7 Insert wood dowels (7) into the holes in the ends of short guardrails (N). Attach short guardrails (N) to top post (A) with wood joint connectors (3). Attach the guardrail leg (R) to the short guardrails (N) and top side rail (H) with flat head wood screws (5).
TWIN BUNK BED 7 8 PCS 2 8 PCS STEP 8 To assemble the ladder, insert wood dowels (7) into the end of the ladder steps (Q). Attach long ladder end (O) and short ladder end (P) to ladder steps (Q) with wood joint connectors (2), using Allen key (9).
TWIN BUNK BED Slats are not shown in illustration for clarity 2 N H I STEP 9 2 6PCS Attach the ladder to the short guardrails (N), the top side rail (H) and bottom side rail (I) with wood joint connectors (2) as shown. NOTE: If a slat (L) is covering the ladder mounting holes, remove the slat (L) and reattach it after the ladder is installed.
Instructions for Converting the bunk bed into two single beds Remove the ladder and all the guardrails. With the help of another person, remove the top bunk from the lower bunk. Disassemble the side rails from all headboards (top and lower bunks). Re-assemble the headboards (with tall posts) and footboards (with short posts) to side rails. Note: Switching the headboards will allow the two single beds to be identical (the headboards will have taller posts and the footboards will have the shorter posts).
TWIN BUNK BED CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK. BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.
MODEL #: Customer Service PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
