Instruction Manual IMPORTANT INFORMATION READ BEFORE ASSEMBLING THIS PRODUCT Follow the information on the warning labels found on the bunk bed and on the packaging. Do not remove the warning label from the bed. Use only a mattress with the dimensions 74-75 in.L x 51.5-52.5 in.W x 9 in.H on the upper bunk. The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the guardrails. Mattress must not exceed the maximum thickness of 9 in.
Attach post (1) to the left side of ladder rungs (7) using double-ended screws (D) and rounded washers (K). Attach ladder rail (6) to the right side of ladder rungs (7) using medium bolts (A) and rounded washers (K). Tighten medium bolts (A) with small wrench (M). Attach guardrail (5) and crossbar (8) to post (1) using small bolts (C) and small washers (F) . Attach post (3) to guardrail (5) and crossbar (8) using small bolts (C) and small washers (F). Tighten small bolts (C) with small wrench (M).
Secure ladder rail (6) to guardrail (5) using samll bolt (C) and samll washer F). Secure ladder rail (6) to crossbar (8) using large bolt (B) and large washer (E) .Tighten samll washer (F) with samll wrench (M) and large bolt (B) with large wrench (L). Attach post (2) to the right side of ladder rungs (7) using double-ended screws (D) and rounded washers (K). Attach ladder rail (6) to the left side of ladder rungs (7) using medium bolts (A) and rounded washers (K).
Attach guardrail (5) and crossbar (8) to post (2) using small bolts (C) and small washers (F) . Attach post (4) to guardrail (5) and crossbar (8) using small bolts (C) and small washers (F). Tighten small bolts (C) with small wrench (M). Secure ladder rail (6) to guardrail (5) using samll bolt (C) and samll washer F). Secure ladder rail (6) to crossbar (8) using large bolt (B) and large washer (E) .Tighten samll washer (F) with samll wrench (M) and large bolt (B) with large wrench (L).
Attach crossbars (10,11,12,14) to the assembly from Step 3 using small bolts (C) and small washers (F) .Tighten samll bolts (C) with samll wrench (M).
Attach crossbars (10,11,12,14) to the assembly from Step 6 using small bolts (C) and small washers (F) .Tighten samll bolts (C) with samll wrench (M).
Insert mattress support bars (9) into the provoded slots of crossbars (10,11).Secure mattress support bars (9) by snapping plastic tab locks (I) into the provided slots of crossbars (10,11). Note that it may be necessary to apply more pressure to some plastic tab locks than others.
M 14 Snap plastic links (J) onto the middle of mattress support bars (9).Attach angle bracket (N) to crossbar (14) using small bolts (C) and small washers (F) .Tighten samll bolts (C) with samll wrench (M).
Attach guardrails (13) to posts (1,2,3,4) using small bolts (C) and small washers (F) . Tighten small bolts (C) with samll wrench (M).
10 Secure front guardrail (13) to crossbar (10) using large bolts (B) and large washers (E). Secure back guardrail (13) to crossbar (11) using large bolts (B), large washers (E) and, where applicable, angle brackets (G).* Tighten large bolts (B) with large wrench (L). *OPTIONAL: Angle brackets (G) can be used to attach the bed to a wall for additional support. You must use hardware suitable for the particular wall type, which is not included as there are many different wall types.
Screw small bolts (C) and insert plastic plugs (H) into the bunk bed assembly.This will fill the holes that are used only with the optional accessory attachments,which are sold separately.