ASSEMBLY INSTRUCTIONS Book Nook Kids Storage Bench with Cubbies White ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over.
This product is suitable for children 3 years and older. THIS STORAGE BENCH WILL HOLD UP TO 20 POUNDS PER CUBBY AND HAS A SEATING CAPACITY OF 75 POUNDS OR A TOTAL OF 155 POUNDS. DO NOT LOAD EACH CUBBY WITH MORE THAN 20 POUNDS OR THE BENCH SEAT WITH MORE THAN 75 POUNDS. IF OVERLOADED WITH MORE THAN 20 POUNDS PER CUBBY OR 75 POUNDS ON THE BENCH SEAT, THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST 1 12 6 9 8 2 5 4 10 11 7 7 3 11 11 11 11 11 NO QTY DESCRIPTION 2 1PC Middle Board 3 1PC Bottom Board 4 1PC Left Side Panel 5 1PC Right Side Panel 6 1PC Upper Slant Board 7 2PCS Divider Board 8 1PC Back Cross Bar 9 1PC Upper Back Panel 10 1PC Lower Back Panel 11 6PCS Wood Leg 12 1PC Cushion 1 1PC Top Board
PARTS LIST NO PARTS QTY DESCRIPTION A 10PCS Cam Bolt B 14PCS Cam Lock C 8PCS Wood Dowel D 4PCS Cam Bolt E 13PCS Screw (4x35mm) F 6PCS Screw (5x40mm) G 1PC Allen Wrench I 2PCS Plastic Anchor J 2PCS Screw (4x30mm) K 2PCS Adjustable Anchor Bracket M 2PCS Screw (4x10mm) TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED) THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
STEP 1 Front 1 D D D D 1 A D A D 1 1. Screw 2 cam bolts (A) into cam bolt holes on top board (1). 2. Screw 2 cam bolts (D) into cam bolt holes on top board (1), make sure cam bolts (D) face correct direction as drawing shows. STEP 2 Front D D D 2 2 D D D 2 1. Screw 2 cam bolts (D) into cam bolt holes on middle board (2), make sure cam bolts (D) face correct direction as drawing shows.
STEP 3 M M K A K A A A 2 1. Screw 4 cam bolts (A) into cam bolt holes on middle board (2) 2. Insert 2 screws (M) through holes on adjustable anchor brackets (K), then tighten to middle board (2). STEP 4 A A A A 4 1. Screw 2 cam bolts (A) into cam bolt holes on left side panel (4). 2. Screw 2 cam bolts (A) into cam bolt holes on right side panel (5).
STEP 5 6 B B D 2 D 1. Attach upper slant board (6) to middle board (2) by inserting cam bolts (D) into cam lock holes on upper slant board (6). 2. Insert 2 cam locks (B) into cam lock holes on upper slant board (6), then rotate clockwise to secure cam bolts (D) in place. STEP 6 6 9 B B 5 B 2 B A A 4 1. Attach right side panel (5) to middle board (2) by inserting cam bolts (A) into cam lock holes on middle board (2). 2.
STEP 7 A 5 2 4 A B B A A 7 7 B B 1. Attach 2 divider boards (7) to middle board (2) by inserting cam bolts (A) into cam lock holes on divider boards (7). 2. Insert 4 cam locks (B) into cam lock holes on divider boards (7), then rotate clockwise to secure cam bolts (A) in place. STEP 8 F 11 3 11 11 11 G F 11 F G F 11 1. Attach 6 wood legs (11) to bottom board (3) by inserting 6 screws (F) through holes on bottom board (3), then tighten to wood legs (11) with Allen wrench (G).
STEP 9 E E E E 10 C 3 E E C C E C C C E C 4 C 1. Slide lower back board (10) into grooves on left side panel (4), right side panel (5) and middle board (2). 2. Insert 8 wood dowels (C) into wood dowel holes on bottom board (3). 3. Attach bottom board (3) to left side panel (4), right side panel (5), divider boards (7) and lower back board (10) by inserting wood dowels (C) into wood dowel holes on left side panel (4), right side panel (5) and divider boards (7).
STEP 11 8 E E 1. E E E Attach back cross bar (8) to back of pre-assembled bench by inserting 5 screws (E) through holes on back cross bar (8), then tighten to back of bench. STEP 12 12 1. Place cushion (12) on bench as shown.
STEP 13 I I K I J OPTION #1 OPTION #2 DRYWALL J J WALL ANCHOR WITH SCREW I J DRYWALL WOOD STUD J SCREW ONLY Option #1: Securing to Drywall 1. 2. Position bench against wall in desired location. Using a pencil, make 2 small marks on wall through holes on brackets (K). Move bench away from wall and screw 2 plastic anchors (I) into wall on pencil marks. Place bench against wall, insert 2 screws (J) through holes on brackets (K), then tighten to plastic anchors (I).
Enjoy Your New Storage Bench! Thank you for purchasing our product. We hope you enjoy it and consider purchasing other items.