V40038BT I USER’S MANUAL
Important Safety Precautions When using your Vivitar Wireless Earbuds, basic safety precautions should always be followed, including the following: 1. READ ALL INSTRUCTIONS BEFORE USING YOUR EARBUDS. 2. Clean using a soft cloth or paper towel. 3. Do not allow children or the infirm to play with your earbuds without adult supervision. 4. Do not expose your earphones to excessive heat, flames or fire. 5. Always press all buttons or switches carefully. Do not manhandle your earbuds. 6.
Introduction Thank you for purchasing the Vivitar Air Free True Wireless Earbuds, item V40038BT. You can use your earbuds with most smartphones and Bluetooth devices to stream music wirelessly. In addition, your earbuds come with a wireless charging case which allow you to charge your earbuds anywhere you go. In order to get the best results when using this device, please read this manual first before using.
A Quick Look at Your Device LED Indicator Light LED Indicator Light FRONT VIEW Power/ Play/Pause/Answer Charging Contact Pins Charging Port SIDE VIEW
Charging Your Earbuds Micro USB Plug USB Plug 1. The USB charging cable has a Micro USB plug and a standard USB plug. 2. Insert the USB charging cable’s Micro USB plug into the charging port on the charging case. (red) = Charging (x1) = 25% (off) = Charging Complete (x2) = 50% (x3) = 75% (x4) = 100% 4. Place the earbuds in the charging case. The LED indicator lights on the earbuds turn red while the earbuds are charging then turns off once charging is complete. 5.
Pairing Your Earphones Together When using your earphones for the first time, it is necessary to first pair the two earphones together so that you can hear audio from both your left and right earphone. To do so, follow the steps below. PRESS & HOLD ~7 SEC 1. Press and hold the power buttons on both earphones simultaneously for approximately 7 seconds. LEFT CHANNEL RIGHT CHANNEL 2. Your earbuds will power on and after a few moments they will pair together.
Pairing Your Earphones with a Smartphone PRESS & HOLD ~2 SEC Pairing Mode Red & BlueFlashing LED 1. Press and hold the power buttons on each earphone for approximately 2 seconds to power them on. 2. The LED indicator lights will alternately flash red and blue to indicate that your earphones are in pairing mode. Paired OFF Vivitar V40038BT 3. Go to the Bluetooth settings menu on your phone. Make sure that Bluetooth is turned on. Connect to the device listed as “Vivitar V40038BT.” 4.
Using Your Earphones Powering Your earphones On and OFF 1. To power on your earphones, press and hold the Power/Play/Pause/Answer buttons until your earphones power on. If you have already paired your earphones to your Bluetooth device, they will automatically remain paired each time you power on your earphones. 2. Press and hold the Power/Play/Pause/Answer button on either earphone for 5-6 seconds to power them both off.
FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Vivitar One Year Warranty This warranty covers the original consumer purchaser only and is not transferable. This warranty covers products that fail to function properly UNDER NORMAL USAGE, due to defects in material or workmanship. Your product will be repaired or replaced at no charge for parts or labor for a period of one year.
Vivitar One Year Warranty (continued) NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THOSE EXPRESSLY DESCRIBED ABOVE SHALL APPLY. DISTRIBUTOR FURTHER DISCLAIMS ALL WARRANTIES AFTER THE EXPRESS WARRANTY PERIOD STATED ABOVE. NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR ENTITY WITH RESPECT TO THE PRODUCT SHALL BE BINDING ON DISTRIBUTOR.