Dome FD8133/8134 Fixed Network Camera Quick Installation Guide English P/N:625011001G Rev. 1.1 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch Português 1MP • MicroSD/SDHC • Compact Design All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Contact your distributor in the event of occurrence. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Contact your distributor in the event of occurrence. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user's manual for the operating temperature.
Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera.
English 1 Package Contents FD8133 or FD8134 Power Adapter Software CD Alignment Sticker Drill hole Cable hole 500024701G Drill hole Quick Installation Guide / Warranty Card RJ45 Female/Female Coupler / Screws / Clamp Core EN - 3
2 Physical Description Light Sensor Lens Black Cover IR LEDs (8 units, distance 10m) (FD8134 only) MicroSD/SDHC Card Slot General I/O Terminal Block Ethernet 10/100 RJ45 Plug Reset Button Status LED 3 Power Cord Socket Hardware Installation First, follow the instructions below to remove the dome cover. Dome Cover Network Camera Model No: FD8134 Record the MAC address before installing the camera. MAC:0002D107258A V I RoHS This device complies with part 15 of the FCC rules.
English Then remove the black cover as shown below. Tilt Adjustment Screw With idiot-proof mechanism design and very compact size, this Network Camera is very easy for user to install in diverse indoor environment. A Ceiling Mount A Wall Mount 1. Attach the alignment sticker to the ceilling/wall. 2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall. 3. The Network Camera can be mounted with the cable routed through the ceiling/wall or from the side.
6. Buckle the supplied clamp core onto the cable to against the EMI radiation. The clamp core should be away from the device at least 5 cm. 5 cm 4 Network Deployment General Connection (without PoE) 1. If you have external DI devices, make the connection from general I/O terminal block. 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. Use a Category 5 Cross Cable when Network Camera is directly connected to PC. 3.
English Power over Ethernet (PoE) (FD8134 only) When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. POWER COLLISION 1 2 3 4 LINK RECEIVE PARTITION 5 PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up.
English 6 Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or recording software. For further setup, please refer to the user's manual on the software CD.
7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens to the desired viewing angle: 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3. Turn the lens to adjust the image orientation.
English 8 Completion 1. Align the inner side of the black cover with the notch on both sides of the lens, fix the black cover. 2. If you choose to the feed the cable through the ceiling/wall, arrange the cable neatly through the cable hole. If you choose to feed the cable from the side, remove plate B. 3. Attach the dome cover to the camera as the direction shown below. With idiot-proof mechanism design, the dome cover cannot be attatched if the angle does not fit.
Dome FD8133/8134 Fixed Network Camera Quick Installation Guide English P/N:625011001G Rev. 1.1 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch Português 1MP • MicroSD/SDHC • Compact Design All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.