FD8162 2 MP • PIR • Focus Assist P/N:625014500G Ver.1.0 Copyright c 2011 VIVOTEK INC. All rights reserved.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Contact your distributor in the event of occurrence. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Contact your distributor in the event of occurrence. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user's manual for the operating temperature.
Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera.
English 1 Package Contents FD8162 Alignment Sticker Software CD T10 Torx Screwdriver/ Screws / Plastic Anchors Quick Installation Guide / Warranty Card DC Power Adapter (Optional) EN - 3
2 Physical Description Light Sensor Camera Front View Black Cover Lens IR LEDs (18 units, effective up to 15m) Focus Assist Button Built-in Microphone Reserved PIR Sensor Camera Rear View Micro SD/ SDHC Card Slot Reset Button Jumpers Microphone Video Output NTSC internal 60Hz external PAL 50Hz 1 2 Reset Int. Micro SD Card 1 2 3 4 5 678 General IO Terminal Block NTSC AV Out Ext. Ethernet PAL Audio In Audio/Video Out Audio In 10/100BaseT Ethernet EN - 4 1. DC 12V2. DC 12V+ 3.
English 3 Hardware Installation Before installing your camera, make sure the built-in PIR (Passive Infrared Sensor) can be directed toward the area of interest, where possible intrusion may occur. (The sensitivity of PIR sensor depends on the object size and temperature differences between the object and the background environment.) Side View Top View 50 5m 41 50 5m 41 Use the included T10 Torx screwdriver to loosen screws on the sides of dome cover to remove it.
Wall Mount Ceiling Mount 1. Attach the alignment sticker to the ceilling/wall. 2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall. 3. The Network Camera can be mounted with the cable routed through the ceiling/wall or from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the above picture. 4. Hammer the supplied plastic anchors into the holes. 5.
English Power over Ethernet (PoE) When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
English 6 Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. For further setup, please refer to the user's manual on the software CD.
7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens to the desired view angle: 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3. Turn the lens to adjust the image orientation.
English 8 Completion 1. Align the notches on the inner side of the black cover with the rivets on the sides of the lens, and then fix the black cover. 2. If you choose to feed the cable through the ceiling/wall, arrange the cables neatly through the cable hole A (not shown in the drawing). If you choose to feed the cable from the side, remove plate B. 3. Attach the dome cover to the camera as the direction shown below. Tighten two screws from the sides of the dome cover. 4.