English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the event of occurrence. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera.
1 Package Contents FD8335H Mounting Plate Alignment Sticker / Ceiling Hole Template Sticker L-type Hex Key Wrench / Moisture Absorber / Screws / Hex Nut / Doublesided Tape / AV Cable Quick Installation Guide / Warranty Card Software CD 5 1 0 0 0 02 2 1 G Waterproof Connector & Bushing EN - 2
English 2 Physical Description Inner View Lens IR LEDs (18 units, effective up to 15m) Black Cover Tilt Adjustment Screw Focus Assist Button Micro SD/SDHC Card Slot Reset Jumpers Button Microphone Video Output NTSC Internal 60Hz External 1 PAL 50Hz 2 Audio/Video Out (green) Microphone In (pink) Ethernet 10/100 RJ45 Socket General I/O Terminal Block 1. There is no internal microphone. Only external microphone is applicable. 2.
Record the MAC address under the camera base before installing the camera. Replace the side opening cover with the included side outlet bushing if you want to route cables from the side of camera. The 1/2" protection conduits and tubing are separately purchased. 3 Hardware Installation First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the camera base. Follow the steps below to install the camera either to a ceiling or a wall.
English Cabling Assembly Connect power lines and if you have external devices such as sensors and alarms, make the connection from the general I/O terminal block. Pin Definitions Top View 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 AC24V_2 AC24V_1 DI3+ DI2+ DI1+ DIDODO+ (12V) Power and IO cables pass through a waterproof connector. The Ethernet cable should be routed through a rubber seal plug. All cables are user-supplied.
Connecting RJ45 Ethernet Cable RJ45 Cable Dimension (unit: mm) Recommended cable gauge: 24AWG (0.51 mm) Assembling Steps Rubber Seal Plug 1 1. Drill a hole on the rubber seal plug and insert an Ethernet cable through the opening. 2. Strip part of the sheath from the Ethernet cable. 2 3. You will need an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable to the camera’s Ethernet RJ45 socket.
English Wall mount 1. Attach the supplied alignment sticker to the wall. 2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding holes and secure the mounting plate with a screwdriver. 4. Feed the cables through the triangular cutout A or side opening B.
Ceiling mount 1. Attach the supplied alignment sticker to the ceiling. 2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceiling. Then hammer the four supplied plastic anchors into the holes. 3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding holes and secure the mounting plate with a screwdriver. 4. Feed the cables through the triangular cutout A or side opening B.
English Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
English 6 Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. For further setup, please refer to the user's manual on the software CD.
To adjust the zoom factor and focus range 1. Loosen the zoom controller and then adjust zoom factor by moving the controller left and right. Upon completion, tighten the zoom controller screw. 2. Loosen the focus controller and then adjust focus range by moving the controller left and right. Upon completion, tighten the focus controller screw. T N W 8 8 Completion 1. Install the black cover. 2. Attach the dome cover to the camera by combining it to the retainer and aligning with the mounting holes. 3.
