English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the event of occurrence. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera.
1 Package Contents FD8362/62E Mounting Plate Alignment Sticker / Ceiling Hole Template Sticker L-type Hex Key Wrench / Silica Gel / Screws / Hex Nut / DC Power Cable / Double-sided Tape Quick Installation Guide / Warranty Card Software CD 510000210G Waterproof Connector & Bushing DC Power Adapter (Optional, for indoor use only) EN - 2
English 2 Physical Description Inner View Light Sensor Vari-focal Lens Black Cover Tilt Adjustment Screw Micro SD/SDHC Card Slot Jumpers Reset Microphone Video Output Button Internal NTSC 60Hz External PAL 50Hz 1 2 Audio/Video Out (green) Microphone In (pink) Ethernet 10/100 RJ45 Socket Heater General I/O Terminal Block NOTE: The heater is only available on FD8362E.
Outer View IP66-rated Vandal-proof Dome Cover Mounting Plate Record the MAC address under the camera base before installing the camera. Replace the side opening cover with the included side outlet bushing if you want to route cables from the side of camera. The 1/2" protection conduits and tubing are separately purchased.
English 3 Hardware Installation First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the camera base. Follow the steps below to install the camera either to a ceiling or a wall. IMPORTANT! Dome cover should be removed because if it should fall during the installation process, physical injury could occur to your co-workers.
Waterproof Connector (A) Sealing Nut (A) (B) Housing (B) (D) Seals (C) Seal (D) (E) Screw Nut (E) Hex Nut (F) (F) Assembling Steps 1. Disassemble the components of the waterproof connector into parts (A) ~ (F) as shown above. waterproof connector (F --> E --> D --> B --> A) as previously described. Refer to the pin definition to connect them to the general I/O terminal block. Note: The recommended cable gauge is 2.0 ~ 2.8 mm. 2. Place the screw nut (E) on the Power and GPIO opening. 3.
o: white/orange stripe O: orange solid g: white/green stripe B: blue solid b: white/blue stripe G: green solid br: white/brown stripe BR: brown solid o O g B b G br BR 1 2 3 4 5 6 7 8 4. Press the Ethernet cable into the routing path at the bottom of the camera so that the cable will not get in the way when the metal mounting plate is attached. 4 Ceiling mount 1. Attach the supplied alignment sticker to the ceiling. 2.
Wall mount 1. Attach the supplied alignment sticker to the wall. 2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding holes and secure the mounting plate with a screwdriver. 4. Feed the cables through the triangular cutout A or side opening B.
English 4 Network Deployment NOTE: 1. The DC power adaptor, if used, should comply with: O/P: 12V DC, 1.5A min., L.P.S. certified. General Connection (without PoE) 2. Pin #3 & 4 AC 24V as alternate power are for indoor use only Pin 4 Pin 3 Pin 2 Pin 1 1. Connect RJ45 Ethernet cable to a switch. Use a Category 5 Cross Cable when your network camera is directly connected to PC. Non-PoE Switch AC 24V±10% POWER Red COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION DC 12V Black Ethernet 2.
When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch. PoE Power Injector (optional) POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION Non-PoE Switch 5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program.
083236 00-02-D1-08-32-36 192.168.5.109 FD8362 0002D1083236 6 Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. For further setup, please refer to the user's manual on the software CD. EN - 11 English 4.
7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-axis mechanism design 1. Loosen the tilt adjustment screws and then turn the lens module up or down. Upon completion, tighten the screw. 2. Turn the lens to adjust the image orientation. The sophisticated 3-axis mechanism design offers very flexible, easy hardware installation for either ceiling or wall mount.
