User's Manual
Table Of Contents
- Software Installation on page 10
- Overview
- VIVOTEK’s FE9380 and FE9382 are two H.265 fisheye fixed dome network cameras, both featuring a detailed 5-Megapixel CMOS sensor that produces superb image clarity. By employing H.265 compression technology and VIVOTEK’s Smart Stream III technology, these
- The cameras are both equipped with a removable IR-cut filter and WDR Pro technology, empowering the cameras to maintain optimal image quality around the clock and unparalleled visibility in high-contrast lighting environments. Moreover, the cameras are de
- * Depending on scene being monitored.
- Revision History
- Read Before Use
- Package Contents
- Symbols and Statements in this Document
- Physical Description
- LED Definition
- Hardware Installation
- Software Installation
- Network Deployment
- Accessing the Network Camera
- Using RTSP Players
- Using 3GPP-compatible Mobile Devices
- Using VIVOTEK Recording Software
- Main Page
- Client Settings
- Configuration
- System > General settings
- System > Homepage layout
- System > Logs
- System > Parameters
- System > Maintenance
- Media > Image
- Media > Video
- Media > Audio
- Media profiles
- Network > General settings
- Network > Streaming protocols
- Network > QoS (Quality of Service)
- Network > SNMP (Simple Network Management Protocol)
- Network > FTP
- Bonjour
- Security > User accounts
- Security > HTTPS (Hypertext Transfer Protocol over SSL)
- Security > Access List
- Security > IEEE 802.1x
- PTZ > PTZ settings
- Event > Event settings
- Applications > Motion detection
- Applications > Smart VCA
- Applications > DI and DO
- Applications > Tampering detection
- Applications > Audio detection
- Applications > Shock detection
- Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform)
- Recording > Recording settings
- Storage
- Storage > SD card management
- Storage > NAS management
- Storage > Content management
- Appendix
VIVOTEK
User's Manual - 409
© 2020 VIVOTEK INC. All Right Reserved
260
PARAMETER VALUE DESCRIPTION
function
focus,
auto,
scan,
stop,
positioning,
irisopen,
irisenable,
resetfocus,
getstatus
Function type
focus – Move focus motor
auto – Perform auto focus
scan – Perform focus scan
stop – Stop current operation
positioning – Position the motors
resetfocus – reset focus position to default
irisopen – Fully open iris. It will maintain fully open iris
status until sending function=irisenable cgi.
irisenable – return back to user setting status of iris.
getstatus–Information of motors, return value as below:
remote_focus_focus_motor_max: Maximum steps of
focus motor
remote_focus_focus_motor_start: Start point of
effective focal length
remote_focus_focus_motor_end: End point of effective
focal length
remote_focus_focus_motor: Current position of focus
motor
remote_focus_focus_enable: Current function of focus
motor
remote_focus_iris_open: The current status of iris. 0:
irisenable, 1: irisopen
Current function of zoom/focus motor, return value as
below:
0: no service
1: zooming
2. focusing
3: auto focus
4: focus scan
5: positioning (both zoom motor and focus motor)
12: reset focus
direction direct,
forward,
backward
Motor’s moving direction.
It works only if function= focus.
© 2020 VIVOTEK INC. All Right Reserved
261
PARAMETER VALUE DESCRIPTION
position
0~<motor_max>
Motor’s position.
It works only if function=focus and direction=direct.
<motor_max> is refer to
remote_focus_focus_motor_max which replied from
"function=getstatus"
steps 1 ~ <motor_max> Motor’s moving steps.
It works only if function=focus and direction=forward or
direction=backward.
<motor_max> is refer to
remote_focus_focus_motor_max which replied from
"function=getstatus"
* This parameter is for additional fine-tune, the value is from 1 to 30.
iris
N/A
Open iris or not.
It works only if function=auto or function=scan.
8.21 Export Files
Note: This request requires Administrator privileges.
Method: GET
Syntax:
For daylight saving time configuration file:
http://<servername>/cgi-bin/admin/exportDst.cgi
For language file:
http://<servername>/cgi-bin/admin/export_language.cgi?currentlanguage=<value>
PARAMETER
VALUE
DESCRIPTION
currentlanguage 0~20 Available language lists.
Please refer to:
system_info_language_i0 ~ system_info_language_i19.
For setting backup file:
http://<servername>/cgi-bin/admin/export_backup.cgi?backup