IP8130/8131 IP8130W/8131W Cube Network Camera Quick Installation Guide 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 繁中 Dansk Indonesia 簡中 日本語 Français Español Deutsch Português Italiano IP8130/8131: 1MP • Compact Size IP8130W/8131W: 1MP • 802.11n WLAN • WPS P/N:625021700G Rev. 1.0 All specifications are subject to change without notice. Copyright c 2013 VIVOTEK INC. All rights reserved. VIVOTEK INC.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user’s manual for the operating temperature. Keep the Network Camera away from direct sunlight. Do not place the Network Camera in high humidity environments.
2 Physical Description Front Panel IP8130/8130W Status LED Lens Microphone IP8131/8131W WPS button Lens Status LED IR LEDs Microphone LED Definitions Item LED status Description 1 Steady Red Powered on, during system boot, or indicating no network connection Powered off Searching for WPS Network connected (wired or wireless) Upgrading firmware 2 3 4 5 All LED off Blinking Blue every 0.15 sec. Blinking Green every 1 sec. Blinking Green and RED intermittently Blinking Orange every 0.
The back panels are identical for all models. Antenna Connector (for wireless models) Reset Button Power Cord Socket 1 2 3 4 3 Ethernet 10/100 RJ45 Socket DIDI+ Audio GND Audio Out General I/O Terminal Block Audio out cable is user-supplied. Install Camera to Stand Attach the camera to stand and orient the shooting angle. If preferred, use the included screws to secure the the camera stand to a mounting surface.
4 Install the Antenna (wireless models) An antenna comes with the camera. Install it by turning clockwise to attach to the connector. 5 Network Deployment LAN Connection 1. If you have external devices such as sensors and alarms, make connections from the general I/O terminal block. 2. Connect the camera to a switch via Ethernet cable or directly to a computer. Ethernet must be connected before power on. 3. Connect the supplied power cable from the camera to a power outlet.
English 6 Assigning an IP Address The following is performed on a computer connected to the same domain via a wired or wireless connection. 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3.
Wireless Connection: Using the WPS Button 1. Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi Protected Setup) functions. WPS enables easy setup with compatible APs. 2. Disconnect your LAN cable, and connect the power cord. 3. Wait for 1 minute for the camera to boot up. Press the WPS button for 1 second. The front panel LED should blink blue. 4. Press and hold down the WPS button on your AP (some router/AP will have a virtual button on their management software instead).
English 8 Wireless Connection: Manual Configuration 1. In addition to the use of WPS function, you can also use a wired connection to manually set up your wireless configuration. 2. Enter the Configuration > Wireless > WLAN page. Key in the same wireless settings as those on your router/AP (SSID, Encryption type, and Pre-shared key). 3. When done, click the Save button, disconnect the Ethernet cable and then reboot the camera (by disconnect and then connect the power cord).
IP8130/8131 IP8130W/8131W Cube Network Camera Quick Installation Guide 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 繁中 Dansk Indonesia 簡中 日本語 Français Español Deutsch Português Italiano IP8130/8131: 1MP • Compact Size IP8130W/8131W: 1MP • 802.11n WLAN • WPS P/N:625021700G Rev. 1.0 All specifications are subject to change without notice. Copyright c 2013 VIVOTEK INC. All rights reserved. VIVOTEK INC.
