720p HD WDR Pro IP67 Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska IP8335H This guide describes the basic functions of IP8335H. More details can be found in the User Manual. Copyright New Taipei City P/N: 625015800G Ver.1.0 2011 VIVOTEK INC. All right reserved.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the event of occurrence. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera.
1 Package Contents IP8335H Alignment Sticker Sun Shield Wrench / RJ45 Female/Female Coupler / Double-sided Tape / Screws Power Adapter Wall Mount Bracket Waterproof Connector (for backup use) Moisture Absorber Quick Installation Guide / Warranty Card Software CD 510000202G EN-2
English 2 Physical Description Light Sensor Lens IR LED Focus Controller Reset Button Zoom Controller General I/O Terminal Block Ethernet 10/100 RJ45 Plug Power Cord Socket Micrso SD/SDHC Card Slot Alternate AC Power Source + - EN-3 AC 24V + AC 24V -
3 Hardware Installation 1. Attach the alignment sticker to the wall. Drill three holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Feed the cables through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next page.) 3. Hang the wall mount bracket on the plate. 4.
English Waterproof Connector Components of the Waterproof Connector Rubber (A) Screw Nut (B) Seal (C) Seals (D) Housing (E) Sealing Nut (F) Pin Definitions The terminal block is accessible when the rear cover is opened. 1 2 3 4 5 6 7 8 J3 Micro SD Socket J7 PCB 1 2 3 4 5 6 7 8 Ethernet Power J3 J7 1 2 3 4 5 6 7 8 Digital Input 1: DI1 Digital Input: - (Ground) RS485 + RS485 AUDIO_GND AUDIO_IN: Ext_MIC_IN AUDIO_GND AUDIO_OUT 1 2 3 4 5 6 7 8 * Vmax.: 40V DC, Imax.: 400mA.
Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (F) as shown above. 2. Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A) and screw nut (B) tightly. 3. Open the back cover of the Network Camera. 4. If you have external devices such as sensors and alarms, feed the cables through the waterproof connector (F --> E --> C --> A+B) as the illustration shown below.
English 4 Network Deployment Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable.
5 Assigning an IP Address 1. Install "Installation Wizard 2" from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. IW2 Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up.
English 6 Ready to Use 1. Access the Network Camera from the LAN. 2. Retrieve live video through a web browser or recording software. For further setup, please refer to the user's manual on the software CD. 3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller. 4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the focus controller.
5. Tighten the lens cover. 6. Replace the moisture absorber with a new one if you open the back cover during the installation procedure. 6 NOTE: 5 Please tear down the aluminum foil vacuum bag and take out the moisture absorber, then attach the moisture absorber with the supplied double-sided tape. NOTE: If you want to use the supplied sun shield for outdoor environments, please follow the steps below to install: 1. Tighten the two supplied hex standoffs. 2.
720p HD WDR Pro IP67 Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska IP8335H This guide describes the basic functions of IP8335H. More details can be found in the User Manual. Copyright New Taipei City P/N: 625015800G Ver.1.0 2011 VIVOTEK INC. All right reserved.
