VC9101, CU9171, CU9183 User ’s Manual Split Type Network Camera 5MP • Multiple Fixed or Fisheye Lens Options • Day & Night • Smart Motion Detection Smart VCA • Smart Stream III Rev. 1.
VIVOTEK Table of Contents Overview �������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3 Revision History ����������������������������������������������������������������������������������������������������������������������������������������������������� 4 Read Before Use ����������������������������������������������������������������������������������������������������������������������������
VIVOTEK Recording > Recording settings �������������������������������������������������������������������������������������������������������������� 151 Storage ���������������������������������������������������������������������������������������������������������������������������������������������������� 156 Storage > NAS management ������������������������������������������������������������������������������������������������������������������� 157 Storage > Content management ��������������������
VIVOTEK Revision History ■ Rev. 1.0: Initial release. Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use.
VIVOTEK Package Contents ■ VC9101 ■ Screw pack, Lens bracket. ■ Quick Installation Guide. For the contents of the lens modules, refer to their QIG. Symbols and Statements in this Document i INFORMATION: provides important messages or advices that might help prevent inconvenient or problem situations. NOTE: Notices provide guidance or advices that are related to the functional integrity of the machine.
VIVOTEK Physical Description Audio jacks 256GB DI/DO terminal To lens module 10 1 - OR - I MicroSD card slot DC8~36V DC plug Application View CU9171-H, CU9183-H Fisheye lens 6 - User's Manual PoE 802.
VIVOTEK CU9171-H, CU9183-H Pinhole 18 24.
VIVOTEK Screws IMPORTANT: Below are things to notice connecting a ground wire: 1. The minimum ground screw type is 3.5mm. 2. The minimum ground wire gauge is 18AWG. 3. Use green/yellow (green yellow stripe) ground wires. 4. Use a knurled washer for securing the grounding srew.
VIVOTEK Hardware Installation 1. Jot down the camera's MAC address for later reference. XXXXXX 0002D10766AD Network Camera Model No: XXXXXX MAC: 0002D1083236 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pat. 6,930,709 Made in Taiwan 2.
VIVOTEK 3. Connect the necessary interfaces. 256GB 10 1 - OR - I DC8~36V PoE 802.3af 4. The 5-meter cable has one Ethernet connector and a USB type C connector to connect the lens module.
VIVOTEK 5. Drill a hole for your lens module. 24 / 21 / 12mm Below are the types of installation for different mount brackets and lenses.
VIVOTEK A A1 A-1. Insert the lens module into the clamp bracket. A-2. Route the module cable.
VIVOTEK Insert the module into the through hole. 24.2mm CU9183-H Note that the fisheye lens must be aligned with the edge of the through hole; otherwise, the field of view will be blocked.
VIVOTEK CU9183-H The same applies to the pinhole lens.
VIVOTEK A3 Adjust the orientation of the lens so that the field of view can be properly aligned. A4 Tighten the retention screw on the clamp bracket.
VIVOTEK A5 Peel off the sticker cover. A6 You can fasten 2 screws to attach the bracket to a wall or panel.
VIVOTEK B B1 CU9183-HF For a thinner panel, drill a hole and fasten the lens module using the included hex nut. <=0.2 inch 5.08mm C C1 CU9171-HF For a thinner panel, drill a hole and fasten the lens module using the included hex nut. <=0.1 inch 2.
VIVOTEK D D1 CU9183-HF CU9171-HF For using the snap-on bracket, press fit the lens module. 1 D2 Secure the installation by fastening two screws from the top.
VIVOTEK D3 Peel off the sticker cover. 3 D3 Attach the bracket to a panel with a pre-drilled hole. For the hole diameters, refer to the previous description.
VIVOTEK E E2 E1 You can also use a standard wall-mount bracket along with a clamp bracket to install the lens module. Install the clamp bracket by turing it clockwise onto the threaded pole. You can then tilt or rotate to find a best shooting direction.
VIVOTEK 7 You can mount the VC9101 main unit to a wall by drilling 2 screw holes 55mm apart. Hang the unit onto the screws.
VIVOTEK 8. Please visit VIVOTEK’s website to Install the "Shepherd” software utility. The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN. Double-click on the camera’s MAC address to open a web console to the camera.
VIVOTEK Software Installation 9. Install the Shepherd utility, which helps you locate and configure your Network Camera in the local network. If your camera comes without the CD, go to VIVOTEK’s website, and locate the utility in the Downloads > Software page. 9-1. Run the Shepherd utility. 9-2. The program will conduct an analysis of your network environment.
VIVOTEK 9-3. The program will search for all VIVOTEK network devices on the same LAN. 9-4. After a brief search, the installer window will prompt. Click on the MAC and model name that matches the one printed on the product label. You can then double-click on the address to open a management session with the Network Camera. Network Camera Model No: FD9367-EHTV-v2 MAC:0002D1730202 R o HS This device complies with part 15 of the FCC rules.
VIVOTEK Forceful Password Configuration 10. The first time you log in to the camera, the firmware will prompt for a password configuration for security concerns. 10-1. Since your camera is used for the first time, there is no password. Enter “root” as the user name, and nothting for the password. 10-2. Enter the combination of alphabetic and numeric characters to fulfill the password strength. requirement. The default name for the camera administrator is “root”, and can not be changed.
VIVOTEK Some, but not all special ASCII characters are supported: !, $, %, -, ., @, ^, _, and ~. You can use them in the password combination. 10-3. Another prompt will request for the password you just configured. Enter the password and then you can start configure your camera and see the live view.
VIVOTEK Hardware Reset The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press the recessed reset button. Wait for the Network Camera to reboot. Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all settings will be restored to factory default.
VIVOTEK Network Deployment General Connection (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoEenabled switch via Ethernet cable. 802.3af PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a nonPoE switch. PoE Power Injector (optional) Non-PoE Switch NOTE: 1.
VIVOTEK Ready to Use 1. A browser session to the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.
VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 20 for details. WAN (Wide Area Network ) Internet Router IP address : from ISP POWER COLLISION 1 2 3 4 5 IP address : 192.168.0.3 Subnet mask : 255.255.255.
VIVOTEK For example, your router and IP settings may look like this: Device IP Address: internal port IP Address: External Port (Mapped port on the router) Public IP of router 122.146.57.120 LAN IP of router 192.168.2.1 Camera 1 192.168.2.10:80 122.146.57.120:8000 Camera 2 192.168.2.11:80 122.146.57.120:8001 ... ... ...
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: 1. Launch your web browser (e.g., Microsoft® Internet Explorer or Mozilla Firefox). 2.
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 107. ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX ® Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. 2.
VIVOTEK IMPORTANT: • Currently the Network Camera utilizes a 32-bit ActiveX plugin. You CAN NOT open a management/view session with the camera using a 64-bit IE browser. • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64. A 32-bit version of IE browser will be installed. • On Windows 7, the 32-bit explorer browser can be accessed from here: C:\Program Files (x86)\Internet Explorer\iexplore.
VIVOTEK Using RTSP Players To view the streaming media using RTSP players, you can use one of the following players that support RTSP streaming. VLC media player VLC media player mpegable Player 1. Launch the RTSP player. pvPlayer 2. Choose File > Open URL. A URL dialog box will pop up. 3. The address format is rtsp://:/ As most ISPs and players only allow RTSP streaming through port number 554, please set the RTSP port to 554.
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 28. To utilize this feature, please check the following settings on your Network Camera: 1.
VIVOTEK Using VIVOTEK Recording Software Visit our website for download the VAST recording software that provides simultaneous monitoring and video recording for multiple Network Cameras. Please install the recording software; then launch the program to add the Network Camera to the Channel list. For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www.vivotek.com. Tips: 1.
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window. Digital zoom is only available in the Liveview profile. VIVOTEK INC. Logo Resize Buttons Host Name Configuration Area Camera Control Area Live View Window VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website. Host Name The host name can be customized to fit your needs.
VIVOTEK Configuration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 43. Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a password be applied to the Network Camera so that only the administrator can configure the Network Camera. For more information, please refer to Configuration on page 48.
VIVOTEK PTZ Panel: This Network Camera supports “digital“ (e-PTZ) pan/tilt/zoom control, which allows roaming a smaller view frame within a large view frame. Please refer to PTZ settiings on page 122 for detailed information. Global View: Click on this item to display the Global View window. The Global View window contains a full view image (the largest frame size of the captured video) and a floating frame (the viewing region of the current video stream).
VIVOTEK Video Control Buttons: Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot: Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format. Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation.
VIVOTEK ■ The following window is displayed when the video mode is set to MJPEG: Video Title Title and Time Video (HTTP-V) 2018/07/25 17:08:56 Time Video 17:08:56 2018/07/25 Video Control Buttons Video Title: The video title can be configured. For more information, please refer to Media > Image on page 65. Time: Display the current time. For more information, please refer to Media > Image on page 65. Title and Time: Video title and time can be stamped on the streaming video.
VIVOTEK Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. H.265/H.264 Protocol Options H.264 Protocol Options Depending on your network environment, there are four transmission modes of H.264 streaming: UDP unicast: This protocol allows for more real-time audio and video streams.
VIVOTEK MP4 Saving Options Users can record live video as they are watching it by clicking page. Here, you can specify the storage destination and file name. Start MP4 Recording on the main Folder: Specify a storage destination on your PC for the recorded video files. The location can be changed. File name prefix: Enter the text that will be appended to the front of the video file name. A specified folder will be automatically created on your local hard disk.
VIVOTEK Joystick settings Enable Joystick Connect a joystick to a USB port on your management computer. Supported by the plug-in (Microsoft’s DirectX), once the plug-in for the web console is loaded, it will automatically detect if there is any joystick on the computer. The joystick should work properly without installing any other driver or software. Then you can begin to configure the joystick settings of connected devices. Please follow the instructions below to enable joystick settings. 1.
VIVOTEK Buttons Configuration In the Button Configuration window, the left column shows the actions you can assign, and the right column shows the functional buttons and assigned actions. The number of buttons may differ from different joysticks. Please follow the steps below to configure your joystick buttons: 1. Choosing one of the actions and click Assign will pop up a dialog. Then you can assign this action to a button by pressing the joystick button or select it from the drop-down list.
VIVOTEK Buttons Configuration Click the Configure Buttons button, a window will prompt as shown below. Please follow the steps below to configure your joystick buttons: 1. Select a button number from the Button # pull-down menu. Tips: If you are not sure of the locations of each button, use the Properties window in the Game Controllers utility. 2. Select a corresponding action, such as Patrol or Preset#. 3. Click the Assign button to assign an action to the button.
VIVOTEK Configuration Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. VIVOTEK provides an easy-to-use user interface that helps you set up your network camera with minimal effort. In order to simplify the user interface, detailed information will be hidden unless you click on the function item.
VIVOTEK System > General settings This section explains how to configure the basic settings for the Network Camera, such as the host name and system time. It is composed of the following two columns: System, and System Time. When finished with the settings on this page, click Save at the bottom of the page to enable the settings. System Host name: Enter a desired name for the Network Camera.
VIVOTEK System time Keep current date and time: Select this option to preserve the current date and time of the Network Camera. The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Synchronize with computer time: Select this option to synchronize the date and time of the Network Camera with the local computer. The read-only date and time of the PC is displayed as updated. Manual: The administrator can enter the date and time manually.
VIVOTEK Western Argentina Summer Time (WARST) is 3 hours behind the prime meridian all year. There is a dummy fall-back transition on December 31 at 25:00 daylight saving time (i.e., 24:00 standard time, equivalent to January 1 at 00:00 standard time), and a simultaneous spring-forward transition on January 1 at 00:00 standard time, so daylight saving time is in effect all year and the initial WART is a placeholder. The format is TZ = local_timezone,date/time,date/time. Here, date is in the Mm.n.
VIVOTEK System > Homepage layout This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the second tab on this page). The settings will be displayed automatically in this Preview field. The following shows the homepage using the default settings: ■ Hide Powered by VIVOTEK: If you check this item, it will be removed from the homepage.
VIVOTEK Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings.
VIVOTEK ■ Follow the steps below to set up the customized homepage: 1. Click Custom on the left column. 2. Click the field where you want to change the color on the right column. Color Selector Custom Pattern 3. The palette window will pop up as shown below. 2 3 1 4 4. Drag the slider bar and click on the left square to select a desired color. 5. The selected color will be displayed in the corresponding fields and in the Preview column. 6. Click Save to enable the settings.
VIVOTEK System > Logs This section explains how to configure the Network Camera to send the system log to a remote server as backup. Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log. 2. In the IP address text box, enter the IP address of the remote server. 2. In the port text box, enter the port number of the remote server. 3. When completed, click Save to enable the setting.
VIVOTEK You can install the included VAST recording software, which provides an Event Management function group for delivering event messages via emails, GSM short messages, onscreen event panel, or to trigger an alarm, etc. For more information, refer to the VAST User Manual.
VIVOTEK Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order. The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit. Set Parameter log VADP log contains the history of changes made to system parameters such as recording, imaging parameters, and all other parameters.
VIVOTEK System > Parameters The View Parameters page lists the entire system’s parameters. If you need technical assistance, please provide the information listed on this page.
VIVOTEK System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to complete the process. Note: Do not power off the Network Camera during the upgrade! Follow the steps below to upgrade the firmware: 1. Download the latest firmware file from the VIVOTEK website. The file is in .pkg file format. 2.
VIVOTEK General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network: Select this option to retain the Network Type settings (please refer to Network Type on page 88). Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to Import/Export files below on this page). Custom Language: Select this option to retain the Custom Language settings.
VIVOTEK The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文. Update custom language file: Click Browse… and specify your own custom language file to upload. Export configuration file: Click to export all parameters for the device and user-defined scripts.
VIVOTEK Media > Image This section explains how to configure the image settings of the Network Camera. It is composed of the following columns: General settings, IR control, Image settings, Exposure, Focus, Privacy mask, and Pixel Calculator. The Focus window is available only for models that come with motorized lens.
VIVOTEK Video orientation: Flip - vertically reflect the display of the live video; Mirror - horizontally reflect the display of the live video. Select both options if the Network Camera is installed upside-down (e.g., on the ceiling) to correct the image orientation. Please note that if you have preset locations, those locations will be cleared after flip/mirror setting. Rotate - If using fisheye lens, this option is not available.
VIVOTEK IR cut filter With a removable IR-cut filter, this Network Camera can automatically remove the filter to let Infrared light pass into the sensor during low light conditions. ■ Auto mode (The Day/Night Exposure Profile will not be available if Auto mode is selected) The Network Camera automatically removes the filter by judging the level of ambient light.
VIVOTEK Image settings On this page, you can tune the White balance and Image adjustment. Sensor Setting 2: For special situations Sensor Setting 1: For normal situations White balance: Adjust the value for the best color temperature. ■ You may follow the steps below to adjust the white balance to the best color temperature. 1. Place a sheet of paper of white or cooler-color temperature color, such as blue, in front of the lens, then allow the Network Camera to automatically adjust the color temperature.
VIVOTEK Highlight mask ■ Strong light sources will be masked from the scene, and the image contrast will be strengthened. This function is useful to prevent the spot-light effects in a high dynamic scene. False color may be observed around the edges of strong light sources. Noise reduction ■ Enable noise reduction: Check to enable noise reduction in order to reduce noises and flickers in image. This applies to the onboard 3D Noise Reduction feature. Use the slide bar to adjust the reduction strength.
VIVOTEK Exposure On this page, you can set the Exposure measurement window, Exposure level, Exposure mode, Exposure time, Gain control, and Day/Night mode settings. You can configure two sets of Exposure settings: one for normal situations, the other for special situations, such as the day/night/schedule mode.
VIVOTEK The inclusive window refers to the “weighted window“; the exclusive window refers to “ignored window“. It adopts the weighted averages method to calculate the value. The inclusive windows have a higher priority. You can overlap these windows, and, if you place an exclusive window within a larger inclusive window, the exclusive part of the overlapped windows will be deducted from the inclusive window. An exposure value will then be calculated out of the remaining of the inclusive window.
VIVOTEK Exposure control: ■ Exposure level: You can manually set the Exposure level, which ranges from -2.0 to +2.0 (dark to bright). You can click and drag the semi-circular pointers on the Exposure time and Gain control slide bars to specify a range of shutter time and Gain control values within which the camera can automatically tune to an optimal imaging result.
VIVOTEK You can click Restore to recall the original settings without incorporating the changes. When completed with the settings on this page, click Save to enable the settings. If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Profile of exposure settings page as shown below. Activated period: Select the mode this profile to apply to: Day mode, Night mode, or Schedule mode. Please manually enter a range of time if you choose Schedule mode.
VIVOTEK Privacy mask Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to address privacy concerns. 4x ■ To configure privacy mask windows, 1. Click New to add a new window. 2. You can use 4 mouse clicks to create a new masking window, which is recommended to be at least twice the size of the object (height and width) you want to cover. 3. Enter a Window Name and click Save to enable the setting. 4.
VIVOTEK Pixel calculator Click the Add button at the lower screen to create a pixel calculator window. Place your cursor on the window to move it to an area of your interest, and change the size of window to fit the area of interest. Once they are drawn, the numbers of pixels on the sides of windows will appear. This allows you to calculate if your current configuration fulfills a requirement, for instance, for recognizing the faces of persons passing through a location.
VIVOTEK Take the following into consideration when using this feature: 1. Operational requirement: Identify a human or a human face. 2. Why human face? There are less variances in the size of a face than that for limbs and body. Human face is normally 16cm wide. 3. The recommended pixel number is, 40 to 80 for facial identification; or 100 pixels per foot (30.48cm) 3-1. One example is a human face in retail. 3-2.
VIVOTEK Media > Video Stream settings The Viewing Window option is not available for fisheye lens. This Network Camera supports multiple streams with frame sizes ranging from 512 x 512 to 1920 x 1920 pixels The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Frame Size" (size of the live view window). ■ Stream 2: The default frame size for Stream 2 is set to the 1920 x 1920.
VIVOTEK Please follow the steps below to set up the configurable settings for a stream: 1. Select a stream for which you want to set up the viewing region. 2. Select a Region of Interest from the drop-down list. The floating frame, the same as the one in the Gloabl View window on the home page, will resize accordingly. If you want to set up a customized viewing region, you can also resize and drag the floating frame to a desired position with your mouse. 3.
VIVOTEK Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing Window sections. This Network Camera provides real-time H.265, H.264 and MJPEG compression standards (Triple Codec) for real-time viewing. If the H.265 or H.264 mode is selected, the video is streamed via RTSP protocol.
VIVOTEK The frame rate will decrease if you select a higher resolution. ■ Intra frame period Determine how often for firmware to plant an I frame. The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds. ■ Smart stream III ■ Dynamic Intra frame period High quality motion codecs, such as H.
VIVOTEK With the H.265 codec in an optimal scenario and when Dynamic Intra frame is combined with the Smart Stream function, an 80% of bandwidth saving can be achieved compared with using H.264 without enabling these bandwidth-saving features. ■ Smart FPS In a static scene, the algorithm puts old frames in queue when no motions occur in scene. When motions occur, the encoding returns to normal to deliver real-time streaming. f1 f1 f1 f1 f5 f5 f5 f5 f9 f5 f6 f7 f8 f9 Motions Occur.
VIVOTEK • Smart codec: Smart codec effectively reduces the quality of the whole or the noninterested areas on a screen and therefore reduces the bandwidth consumed. You can manually specify the video quality for the foreground and the background areas. Select an operation mode if Smart codec is preferred. - Auto tracking: The Auto mode configures the whole screen into the non-interested area. The video quality of part of the screen returns to normal when one or more objects move in that area.
VIVOTEK As the result, the lower screen is constantly displayed in high details, while the upper half is transmitted using a lower-quality format. Although the upper half is transmitted using a lower quality format, you still have an awareness of what is happening on the whole screen.
VIVOTEK ■ Bit rate control Constrained bit rate: • A complex scene generally produces a larger file size, meaning that higher bandwidth will be needed for data transmission. The bandwidth utilization is configurable to match a selected level, resulting in mutable video quality performance. The bit rates are selectable at the following rates: 20Kbps, 30Kbps, 40Kbps, 50Kbps, 64Kbps, 128Kbps, 256Kbps, 512Kbps, 768Kbps, 1Mbps, 2Mbps, 3Mbps, 4Mbps, 6Mbps, 8Mbps, 10Mbps, 12Mbps, 14Mbps, ~ to 80Mbps.
VIVOTEK Fixed quality: On the other hand, if Fixed quality is selected, all frames are transmitted with the same quality; bandwidth utilization is therefore unpredictable. The video quality can be adjusted to the following settings: Medium, Standard, Good, Detailed, and Excellent. You can also select Customize and manually enter a value.
VIVOTEK If the JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. Because the media contents are a combination of JPEG images, no audio data is transmitted to the client.
VIVOTEK Media > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the following message is displayed: Internal microphone input: Select the gain of the internal audio input according to ambient conditions. Adjust the gain from +21 db (most sensitive) or -33 db (least sensitive).
VIVOTEK Audio clips ■ Output gain: Use the slide bar to change the audio output gains value. ■ Audio clip: When the camera's audio input is connected to a microphone, you can record a short period of audio recordings (1 to 10 seconds). You can also use the camera's embedded microphone to record an audio clip, if available. Because the memory space is limited, a recording count down will be available on screen. You can also upload an audio file to the camera's flash memory.
VIVOTEK Media profiles You can configure a different video stream for each of the 3 default profiles, Max. view, Recording, Live view, and App. The related video stream information will display, including stream number, resolution, codec used, frame rate, etc. The Multicast port number, and address for video, audio, and Metadata configuration will also be listed.
VIVOTEK Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network Type is LAN. Please rememer to click on the Save button when you complete the Network setting.
VIVOTEK Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer names and IP addresses. Secondary WINS server: The secondary WINS server that maintains the database of computer names and IP addresses.
VIVOTEK NOTE: ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera. ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support UPnP port forwarding. ► Steps to enable the UPnP TM user interface on your computer: Note that you must log on to the computer as a system administrator to install the UPnP TM components. 1.
VIVOTEK 4. In the Networking Services dialog box, select Universal Plug and Play and click OK. 5. Click Next in the following window. 6. Click Finish. UPnP TM is enabled. ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices added to a network. Services and capabilities offered by networked devices, such as printing and file sharing, are available among each other without the need for cumbersome network configuration.
VIVOTEK Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with a link-local IPv6 address accordingly. IPv6 Information: Click this button to obtain the IPv6 information as shown below.
VIVOTEK Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
VIVOTEK User's Manual - 93
VIVOTEK Network > Streaming protocols NOTE: The metadata information can only be transmitted through the HTTP main port. Metadata is not available through the secondary HTTP port. HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 107 for details.
VIVOTEK URL command -- http://:/ For example, when the Access name for stream 2 is set to video1s2.mjpg: 1. Launch Mozilla Firefox or Netscape. 2. Type the above URL command in the address bar. Press Enter. 3. The JPEG images will be displayed in your web browser. http://192.168.5.151/video1s2.
VIVOTEK Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted. If digest authentication is selected, user credentials are encrypted using MD5 algorithm, thus providing better protection against unauthorized access.
VIVOTEK Multicast settings for streams: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for video streams. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.
VIVOTEK SIP SIP is short for Session Initiation Protocol. If necessary, you can change the default port number, 5060, to one between 1025 and 65535. Two way audio port: By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and 65535. The Network Camera supports two way audio communication so that operators can transmit and receive audio simultaneously.
VIVOTEK Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Express Link is a free service provided by VIVOTEK server, which allows users to register a domain name for a network device. One URL can only be mapped to one MAC address.
VIVOTEK Manual setup DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting. Provider: Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net, a free dynamic domain name service, to VIVOTEK customers. It is recommended that you register Safe100.net to access VIVOTEK’s Network Cameras from the Internet. Additionally, we offer other DDNS providers, such as Dyndns.org(Dynamic), Dyndns. org(Custom), TZO.com, DHS.
VIVOTEK [Register] Successfully Your account information has been mailed to registered e-mail address 4. Select Enable DDNS and click Save to enable the setting. ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators. You can use CustomSafe100 to register a dynamic domain name if your distributor or system integrators offer such services. 1. In the DDNS column, select CustomSafe100 from the drop-down list. 2.
VIVOTEK Network > QoS (Quality of Service) Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network. Quality of service guarantees are important if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
VIVOTEK QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64 different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop Behavior (PHB).
VIVOTEK Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. It helps network administrators to remotely manage network devices and find, solve network problems with ease. ■ The SNMP consists of the following three key components: 1.
VIVOTEK Network > FTP The newer firmware disabled the FTP port for security concerns. You can manually enable the FTP server service to enable the FTP function. You can disable the FTP server function when it is not in use. FTP port: The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Shepherd utility to upgrade the firmware via FTP server. By default, the FTP port is set to 21. It can also be assigned to another port number between 1025 and 65535.
VIVOTEK Bonjour To access the camera from a Mac computer, go to Safari, click on Bonjour and select the camera from a drop-down list. You can go to Safari > Preferences to enter your user name and password, and provide the root password the first time you access the camera. The camera main page will open in your browser. Some later iOSes may come without the Bonjour option. Install the Discovery utility instead. Find the Discovery (formerly Bonjour Browser) from the Mac App Store.
VIVOTEK Security > User accounts This section explains how to enable password protection and create multiple accounts. Account management The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Account management window, please apply the password for the “root” account first. The administrator can create up to 20 user accounts. To create a new user, 1. Click to unfold the pull-down menu. Select New user. 2.
VIVOTEK Privilege management PTZ control: You can modify the management privilege as operators or viewers. Select or deselect the checkboxes, and then click Save to enable the settings. If you give Viewers the privilege, Operators will also have the ability to control the Network Camera through the main page. (Please refer to Configuration on page 48).
VIVOTEK Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Install Certificate Method Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
VIVOTEK 5. Click Save to preserve your configuration, and your current session with the camera will change to the encrypted connection. 6. If your web session does not automatically change to an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS. https:// https://192.168.5.151/index.
VIVOTEK Create certificate request and install 1. Select the option from the Method pull-down menu. 2. Click Create certificate to proceed. 3. The following information will show up in a pop-up window after clicking Create. Then click Save to generate the certificate request. 4. The Certificate request window will prompt. If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups.
VIVOTEK 5. Look for a trusted certificate authority, such as Symantec’s VeriSign Authentication Services, that issues digital certificates. Sign in and purchase the SSL certification service. Copy the certificate request from your request prompt and paste it in the CA’s signing request window. Proceed with the rest of the process as CA’s instructions on their webpage. 6. Once completed, your SSL certificate should be delivered to you via an email or other means.
VIVOTEK 7. Open a new edit, paste the certificate contents, and press ENTER at the end of the contents to add an empty line. 8. Convert file format from DOS to UNIX. Open File menu > Conversions > DOS to Unix.
VIVOTEK 9. Save the edit using the “.crt” extension, using a file name like “CAcert.crt.” 10. Return to the original firmware session, use the Browse button to locate the crt certificate file, and click Upload to enable the certification.
VIVOTEK 11. When the certifice file is successfully loaded, its status will be stated as Active. Note that a certificate must have been created and installed before you can click on the “Save" button for the configuration to take effect. 12.To begin an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS.
VIVOTEK Security > Access List This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link (IE Explorer or Quick Time Player).
VIVOTEK ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explore or Quick Time Player). If you want to enable the denied list, please check Enable access list filtering and click Save in the first column.
VIVOTEK There are three types of rules: Single: This rule allows the user to add an IP address to the Allowed/Denied list. For example: 192.168.2.1 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. The address and network mask are written in CIDR format. For example: IP address range 192.168.2.x will be bolcked. If IPv6 filter is preferred, you will be prompted by the following window.
VIVOTEK Security > IEEE 802.1X Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x standard is designed to enhance the security of local area networks, which provides authentication to network devices (clients) attached to a network port (wired or wireless).
VIVOTEK 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically. NOTE: ► The authentication process for 802.1x: 1. The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the supplicant) and the RADIUS Server (the authentication server). 2. A Network Camera requests access to the protected LAN using 802.
VIVOTEK Security > Miscellaneous The embedded TrendMicro utitlity provides the protection against Cross-Site Request Forgery. Cross-site request forgery is also known as one-click attack or session riding and is abbreviated as CSRF. CSRF is a type of malicious exploit of a website, in this case, the camera. Unauthorized commands are transmitted from a user that the web application trusts, using the mechanism of forging a trusted user's own request with a request containing his own cookies, etc.
VIVOTEK PTZ > PTZ settings The digital PTZ applies to a fixed or pinhole lens. This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. Digital: Control the e-PTZ operation. Within a field of view,it allows users to quickly move the focus to a target area for close-up viewing without physically moving the camera. Digital PTZ Operation (E-PTZ Operation) The e-PTZ control settings section will be displayed as shown below: 2015/05/20 09:57:30 x1.8 x1.
VIVOTEK Home page in the E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected position. ■ If you have set up different preset positions for different streams, you can select one of the video streams to display its separate preset positions. Global View In addition to using the e-PTZ control panel, you can also use the mouse to drag or resize the floating frame to pan/tilt/zoom the viewing region.
VIVOTEK Patrol settings You can select some preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click . 2. The selected preset locations will be displayed on the Patrol locations list. 3. Set the Dwelling time for the preset location during an auto patrol. 4. If you want to delete a preset location from the Patrol locations list, select it and click Remove. 5.
VIVOTEK NOTE: • • The Preset Positions will also be displayed on the Home page. Select one from the Go to menu, and the Network Camera will move to the selected preset position. Click Patrol: The Network Camera will patrol along the selected positions repeatedly.
VIVOTEK Event > Event settings This section explains how to configure the Network Camera to respond to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. Click on Help, there is an illustration shown in the pop-up window explaining that an event can be triggered by many sources, such as motion detection or external digital input devices.
VIVOTEK ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this checkbox to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. seconds: Enter the duration in seconds to pause ■ Detect next motion detection or digital input after motion detection after a motion is detected. This can prevent event-related actions to take place too frequently. 1.
VIVOTEK ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with. To enable this function, you need to configure the Tampering Detection option first. Please refer to page 145 for detailed information. ■ Manual Triggers This option allows users to enable event triggers manually by clicking the on/off button on the homepage. Please configure 1 to 3 associated events before using this function.
VIVOTEK Once the triggers are configured, they will be listed under the VADP option. 3. Action Define the actions to be performed by the Network Camera when a trigger is activated. ■ Backup media if the network is disconnected Select this option to backup media file on SD card if the network is disconnected. This function will only be displayed after you set up a network storage (NAS). The media to back up can include snapshot images, video, or system logs depending on your event settings.
VIVOTEK Add server It is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server to open the server setting window. You can specify where the notification messages are sent to when a trigger is activated. A total of 5 server settings can be configured. There are four choices of server types available: Email, FTP, HTTP, and Network storage.
VIVOTEK To verify if the email settings are correctly configured, click Test. The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings. Note that after you configure the first event server, the new event server will automatically display on the Server list. If you wish to add other server options, click Add server. Server type - FTP Select to send the media files to an FTP server when a trigger is activated.
VIVOTEK ■ Passive mode Most firewalls do not accept new connections initiated from external requests. If the FTP server supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the firewall. The firmware default has the Passive mode checkbox selected. To verify if the FTP settings are correctly configured, click Test. The result will be shown in a pop-up window as shown below. If successful, you will also receive a test.txt file on the FTP server.
VIVOTEK If key authentication is not preferred, you can specify a username and password in the section below. An RSA key fingerprint will look like this: da:47:93:b4:3a:90:5b:50:1f:20:a8:f9:b7:a1:d0:e1. Verify if this is the SFTP server you want to connect to. ■ Folder name Enter the folder where the media file will be placed. If the folder name does not exist, the Network Camera will create one on the SFTP server. Use backslash “\” when you need to specify a path.
VIVOTEK Publickey mode: Selecting the Public key mode will bring up the Pairing mode options: Auto, Download, Upload. Auto Camera will generate a key pair and auto pair public key with the SFTP server. Download Camera will generate a key pair and download the public key for the user to upload it to the SFTP server. The supported formats are: ED25519 (default.
VIVOTEK Server type - HTTP Select to send the media files to an HTTP server when a trigger is activated. ■ Server name: Enter a name for the server setting. ■ URL: Enter the URL of the HTTP server. ■ User name: Enter the user name if necessary. ■ Password: Enter the password if necessary. To verify if the HTTP settings are correctly configured, click Test. The result will be shown in a popup window as shown below. If successful, you will receive a test.txt file on the HTTP server.
VIVOTEK Network storage: Select to send the media files to a networked storage when a trigger is activated. Please refer to NAS server on page 154 for details. Note that only one NAS server can be configured. Click Save server to enable the settings. ■ SD Test: Click to test your SD card. The system will display a message indicating the result as a success or a failure. If you want to use your SD card for local storage, please format it before use. Please refer to page 138 for detailed information.
VIVOTEK Click 20190120 to open the directory: The format is: HH (24r) Click to open the file list for that hour 2019/01/20 2019/01/20 Click to go back to the previous level of the directory Click to delete selected items Click to delete all recorded data 2019/01/20 2019/01/20 The format is: File name prefix + Minute (mm) You can set up the file name prefix on Add media page. Please refer to next page for detailed information.
VIVOTEK Add media Click Add media to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item to display the detailed configuration options. You can configure either one or all of them. Media type - Snapshot Select to send snapshots when a trigger is activated.
VIVOTEK ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Snapshot_20190513_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Note that after you set up the first media server, a new column for media server will automatically display on the Media list. If you wish to add more media options, click Add media.
VIVOTEK ■ Maximum file size Specify the maximum file size allowed. Some users may need to stitch the video clips together when searching and packing up forensic evidence. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Video_20190513_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Media type - System log Select to send a system log when a trigger is activated.
VIVOTEK In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action. When completed, click the Save event button to enable the settings and click Close to exit Event Settings page. The new Event / Server settings / Media will appear in the event drop-down list on the Event setting page.
VIVOTEK Applications > Motion detection The camera comes with a Smart Motion Detection utility as its pre-loaded VCA package. Please refer to its User Guide for more information: http://download.vivotek.com/downloadfile/solutions/vadp/smart-motion-detection-manual_ en.pdf. Click on Configuration > Applications > Motion detection. The Smart Motion utility will be automatically started. If Human detection is applied, make sure you measured the height of your camera at the installation site.
VIVOTEK Applications > Smart VCA Smart VCA provides the following features: Intrusion detection, Loitering detection, Missing object detection, Unattended Object detection, Line Crossing detection, and Face detection. Please refer to Smart VCA’s user documentation for more information. Click on Configuration > Applications > Smart VCA. The Smart VCA utility will be automatically started. The Smart Motion detection and Smart VCA share the same utility window.
VIVOTEK Applications > DI and DO Digital input: Select High or Low as the Normal status for the digital input connection. Connect the digital input pin of the Network Camera to an external device to detect the current connection status. Digital output: Select Grounded or Open to define the normal status for the digital output. Connect the digital output pin of the Network Camera to an external device to determine the current status. Set up the event source as DI on Event > Event settings > Trigger.
VIVOTEK Applications > Tampering detection This section explains how to set up camera tamper detection. With tamper detection, the camera is capable of detecting incidents such as redirection, blocking or defocusing, or even spray paint. Please follow the steps below to set up the camera tamper detection function: 1. Click to select the checkbox before tampering conditions: Tampering detection, Image too dark, Image too bright, and Image too blurry. Enter the tamper trigger duration. (10 sec. ~ 10 min.).
VIVOTEK Applications > Audio detection Audio detection, along with video motion detection, is applicable in the following scenarios: 1. Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a door/window. 2. A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of machines. 3. A PTZ camera can be directed to turn to a preset point by the occurrence of audio events. 4.
VIVOTEK You can use the Profile window to configure a different Audio detection setting. For example, a place can be noisy in the day time and become very quiet in the night. 1. Click on the Enable this profile checkbox. Once the Audio detection window is opened, the current sound input will be interactively indicated by a fluctuating yellow wave diagram. 2. Use a mouse click to drag the Alarm level tab to a preferred location on the slide bar. 3. Select the Day, Night, or Schedule mode check circles.
VIVOTEK Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) The camera comes embedded with the Smart Motion Detection feature. The Smart Motion detection, with Human detection and tunable time filter, can eliminate the defects of traditional motion detection and facilitate the configuration at a surveillance site. To learn more about this feature, download its User Guide in: http://download.vivotek.com/downloadfile/solutions/vadp/smart-motion-detection-manual_ en.
VIVOTEK To utilize a software module, acquire the software package and click Browse and Upload buttons. The screen message for a successful upload is shown below: To start a module, select the checkcircle in front, and click the Start button. If you should need to remove a module, select the checkcircle in front and then click the Stop button. By then the module status will become OFF, and the X button will appear at the end of the row. Click on the X button to remove an existing module.
VIVOTEK On the License page, register and activate the license for using VIVOTEK's VADP modules. You should acquire the license key elsewhere, and manually upload to the network camera. Follow the onscreen instruction on VIVOTEK's website for the registration procedure.
VIVOTEK Recording > Recording settings This section explains how to configure the recording settings for the Network Camera. Recording Settings Insert your SD card and click here to test NOTE: ► Please remember to format your SD card via the camera’s web console (in the Local storage . SD card management page) when using it for the first time. Please refer to page 156 for detailed information. Recording Settings Click Add to open the recording setting window.
VIVOTEK If you enable adaptive recording on a camera, only when an event is triggered on Camera A will the server record the full frame rate streaming data; otherwise, it will only request the I frame data during normal monitoring, thus effectively saves bandwidths and storage space. NOTE: ► To enable adaptive recording, please make sure you’ve set up the trigger source such as Motion Detection, DI Device, or Manual Trigger.
VIVOTEK 2. Destination You can select the SD card or network storage (NAS) for the recorded video files. If you have not configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1. Fill in the information for your server. For example: 3 Network storage path (\\server name or IP address\folder name) 1 2 4 User name and password for your server 2. Click Test to check the setting.
VIVOTEK If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: You can choose either the entire free space available or limit the reserved space. The recording size limit must be larger than the reserved amount for cyclic recording. The reserved space is a small amount of space used only for the transaction stage when the capacity is about to be used up or recycled.
VIVOTEK f you want to enable recording notification, please click Event to configure event triggering settings. Please refer to Event > Event settings on page 126 for more details. When completed, select Enable this recording. Click Save to enable the setting and click Close to exit this page. When the system begins recording, it will send the recorded files to the network storage. The new recording name will appear in the drop-down list on the recording page as shown below.
VIVOTEK Storage NOTE: • • • • • It is recommended to turn OFF the recording activity before you remove an SD card from the camera. The lifespan of an SD card is limited. Regular replacement of the SD card can be necessary. Camera filesystem takes up several megabytes of memory space. The storage space cannot be used for recording. Using an SD card that already contains data recorded by another device should not be used in this camera. Please do not modify or change the folder names in the SD card.
VIVOTEK SD card control ■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you wish to retain a file. For example, if you enter “7 days”, the recorded files will be stored on the SD card for 7 days. Click Save to enable your settings.
VIVOTEK 2. Click Test to check the setting. The result will be shown in the pop-up window. If successful, you will receive a test.txt file on the networked storage server. 3. Click Mount to complete the settings. NAS management ■ Minimum reserved storage space: The reserved space can be used as a safe buffer especially when the cyclic recording function is enabled, during the transaction stage when a storage space is full and the incoming streaming data is about to overwrite the previously saved videos.
VIVOTEK Storage > Content management This section explains how to manage the content of recorded videos on the Network Camera. Here you can search and view the records and view the searched results. Searching and Viewing the Records This column allows the user to set up search criteria for recorded data. If you do not select any criteria and click Search button, all recorded data will be listed in the Search Results column. ■ File attributes: Select one or more items as your search criteria.
VIVOTEK Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction. Numbers of entries displayed on one page Click to open a live view ■ Play: Click on a search result which will highlight the selected item. A Play window will appear on top for immediate review of the selected file.
VIVOTEK ■ Lock/Unlock: Select the checkbox in front of a desired search result, then click this button. The selected items will become Locked, which will not be deleted during cyclic recording. You can click again to unlock the selections. For example: Click to switch pages ■ Remove: Select the desired search results, then click this button to delete the files.
VIVOTEK Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application programming interface. The HTTP-based camera interface provides the functionality to request a single image, control camera functions (PTZ, output relay etc.), and get and set internal parameter values.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 2. Style Convention In URL syntax and in descriptions of CGI parameters, a text within angle brackets denotes a content that is to be replaced with either a value or a string. When replacing the text string, the angle brackets shall also be replaced. An example of this is the description of the name for the server, denoted with in the URL syntax description below, which is replaced with the string myserver in the URL syntax example, also below.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory. The file extension .cgi is required.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 4. Security Level SECURITY LEVEL 0 1 [view] 4 [operator] SUB-DIRECTORY anonymous viewer operator 6 [admin] admin 7 N/A DESCRIPTION Unprotected. Can view, listen, and talk to camera. Operator access rights can modify most of the camera’s parameters except some privileges and network options. Administrator access rights can fully control the camera’s operations. Internal APIs. Unable to be changed by any external interfaces.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/getparam.cgi?[] [&…] http:///cgi-bin/viewer/getparam.cgi?[] [&…] http:///cgi-bin/operator/getparam.cgi?[] [&…] http:///cgi-bin/admin/getparam.
© 2022 VIVOTEK INC. All Right Reserved VIVOTEK Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n 29 User's Manual - 167
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/setparam.cgi? = [&=…][&return=] http:///cgi-bin/viewer/setparam.cgi? = [&=…][&return=] http:///cgi-bin/operator/setparam.
© 2022 VIVOTEK INC. All Right Reserved VIVOTEK http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n 31 User's Manual - 169
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7. Available Parameters on the Server Valid values: VALID VALUES string[] string[n~m] password[] ~ domain name[] email address [] , , , … blank everything inside <> integer primary key available non-available valid 170 - User's Manual DESCRIPTION Text strings shorter than ‘n’ characters.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved VALID VALUES non-valid DESCRIPTION The API is listed in product WebAPIs, but is malfunction in this status. Any decimal number expressed in 32-bits ranging from 1.18e38~3.40e+38. NOTE: The camera should not be restarted when parameters are changed. 7.1 System Group: system NAME hostname string[64] SECURITY (get/set) 1/6 ledoff 6/6 date , keep, auto , 6/6 keep, auto
VIVOTEK NAME 172 - User's Manual © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) DESCRIPTION York, Toronto -201: GMT-05:00 Bogota, Lima, Quito, Indiana -180: GMT-04:00 Caracas -160: GMT-04:00 Atlantic Time(Canada), La Paz -140: GMT-03:30 Newfoundland -120: GMT-03:00 Brasilia, Buenos Aires, Georgetown, Greenland, Sao Paulo -121: GMT-03:00 Santiago -80: GMT-02:00 Mid-Atlantic -40: GMT-01:00 Azores, Cape Verde Is.
© 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME reset restoreexceptnet VALUE integer> 0, 0, SECURITY (get/set) DESCRIPTION 7/6 Restart the server after seconds if is non-negative. 7/6 Restore the system parameters to default values except (ipaddress, subnet, router, dns1, dns2, pppoe). This command can cooperate with other “restoreexceptXYZ” commands.
© 2022 VIVOTEK INC. All Right Reserved NAME restoreexceptlen connection_timeout VALUE 0, SECURITY (get/set) 7/6 6/6 VIVOTEK DESCRIPTION parameters will be restored to the default value except for a union of the combined results. * Only available when "capability_image_c<0~(n1)>_remotefocus" != 0. Restore the system parameters to default values except lens profile. This command can cooperate with other “restoreexceptXYZ” commands.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE Español language_i3 : Français language_i4 : Italiano language_i5 : 日 本語 language_i6 : Português language_i7 : 简 体中文 language_i8 : 繁 體中文 customlanguage_max 0, customlanguage_coun 0, customlanguage_i<0~ string (maxcount-1)> SECURITY (get/set) DESCRIPTION 0/6 Maximum number of custom languages supported on the server. Number of custom languages which have been uploaded to the server.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Group: di_i<0~(k-1)> for k is the value of "capability_ndi" (capability_ndi > 0) k is determined by the below criterion: The following applies for capability_extension_di_num >= 0 * if extension_connected=1, k=capability_ndi * if extension_connected=0, k=capability_ndi+ capability_extension_di_num Otherwise, * k=capability_ndi NAME normalstate VALUE high, low SECURITY DESCRIPTION (get/set) 1/1 Indicates open circuit or closed circuit (inactive status) 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE user_i0_pass user_i<1~20>_pass user_i0_privilege password[64] password[64] view, operator, admin view, operator, admin user_i<1~20>_ privilege SECURITY (get/set) 7/6 7/6 6/7 DESCRIPTION 6/6 User privilege Root password User password Root privilege 7.
VIVOTEK NAME ipaddress subnet router dns1 dns2 wins1 wins2 © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) 6/6 6/6 6/6 6/6 6/6 6/6 6/6 DESCRIPTION dns1, dns2 from DHCP server at next reboot. 0 => Use preset ipaddress, subnet, rounter, dns1, and dns2. IP address of server. Subnet mask. Default gateway. Primary DNS server. Secondary DNS server. Primary WINS server. Secondary WINS server. 7.6.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE enable vlanid video audio eventalarm management eventtunnel 1~4095 0~7 0~7 SECURITY (get/set) 6/6 6/6 6/6 6/6 0~7 0~7 0~7 6/6 6/6 6/6 DESCRIPTION Enable/disable CoS (IEEE 802.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.6.5 HTTP Subgroup of network: http NAME VALUE port alternateport authmode s<0~(capability_nmed iastream*capability_n videoin)1)>_accessname 80, 1025 ~ 65535 1025~65535 basic, digest string[32] SECURITY (get/set) 1/6 DESCRIPTION 6/6 1/6 Alternate HTTP port. HTTP authentication mode. 1/6 Http server push access name for stream N, N= 1~(capability_nmediastream*capability_ nvideoin)-1).
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION The value are shown as video1s1.mjpg = c0_s0_accessname, (channel1stream1) video1s2.mjpg = c0_s1_accessname, (channel1stream2) video2s1.mjpg = c1_s0_accessname, (channel2stream1) video2s2.mjpg = c1_s1_accessname, (channel2stream2) etc. * We support this parameter when the version number (httpversion) is equal or greater than 0311c. 7.6.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) c<0~(capability_nvide oin)1>_s<0~(capability_n mediastream)1)>_accessname string[32] 1/6 pimssm_enable 7/6 DESCRIPTION live1s4.sdp = s3_accessname, (channel1stream4) etc. * Values start with prefix “cgi-bin” are prohibited. For example, “c, cg, cgi, cgi-, cgi-b, cgi-bi, cgi-bin” are not allowed.
© 2022 VIVOTEK INC. All Right Reserved NAME VALUE alwaysmulticast ipaddress VIVOTEK SECURITY (get/set) 4/4 DESCRIPTION 4/4 videoipaddress 4/4 audioipaddress 4/4 metadataipaddres s 4/4 videoport 1025 ~ 65535 1025 ~ 65535 4/4 Multicast video IP address. * We replace "network_rtsp_s<0~(n1)>_multicast_ipaddress" with " network_rtsp_s<0~(n1)>_multicast_videoipaddress ".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE DESCRIPTION 1025 ~ 65535 SECURITY (get/set) 6/6 videoport audioport 1025 ~ 65535 6/6 Audio channel port for RTP. metadataport 1025 ~ 65535 6/6 Metadata channel port for RTP. Video channel port for RTP. 7.6.12 PPPoE Subgroup of network: pppoe (capability_protocol_pppoe > 0) NAME VALUE SECURITY DESCRIPTION (get/set) user string[128] 6/6 PPPoE account user name. pass password[64] 7/6 PPPoE account password. 7.6.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE enable admin_enable admin_ip maxconnection string[43] 1~ "capability_protoc ol_maxconnection" 0, 1 6/6 type ipv4list_i<0~9> ipv6list_i<0~9> Single address: Network address: Range address: string[43] SECURITY (get/set) 6/6 6/6 6/6 6/6 DESCRIPTION Enable access list filtering. Enable administrator IP address. Administrator IP address.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE etc SECURITY (get/set) (Available values are listed in "capability_image_ c<0~(n1)>_wbmode") exposurelevel 188 - User's Manual 0~12 4/4 DESCRIPTION a. if "rbgain" is not supported, this means keep current white balance status. b. if "rbgain" is supported, "rgain" and "bgain" are updated to the current values which is got from white balance module. Then, act as rbgain mode "widerange": Auto Tracing White balance (2000K to 10000K).
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) irismode fixed, indoor, outdoor 4/4 enableblc 4/4 color 0, 1 4/4 flip 4/4 mirror 4/4 DESCRIPTION * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. Control DC-Iris mode.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) rotate 0,90,180,270 1/4 ptzstatus 0, 1/7 text string[64] 1/4 imprinttimestamp 4/4 190 - User's Manual DESCRIPTION when "capability_nvideoin > 1". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. The rotation angle of image. Support only in Rotation mode.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE minexposure <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc. SECURITY (get/set) 4/4 * Available value is listed in "capability_image_ c<0~(n1)>_exposure_minr ange" maxexposure <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc.
VIVOTEK NAME enablepreview © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) 1/4 DESCRIPTION when "capability_nvideoin > 1". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. Usage for UI of exposure settings. Preview settings of video profile. * Only available when "capability_image_c<0~(n1)>_exposure_mode" !=0 * We do not support this parameter when "capability_nvideoin > 1".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( get/set) rgain 0~100 4/4 bgain 0~100 4/4 exposurelevel 0~12 4/4 DESCRIPTION balance (2000K to 10000K). "outdoor": auto white balance mode specifically for outdoor. "indoor": auto white balance mode specifically for indoor. "sodiumauto": sodium vapor lamps. * Only available when "capability_image_c<0~(n1)>_wbmode" !="-" Manual set rgain value of gain control setting.
VIVOTEK NAME exposuremode © 2022 VIVOTEK INC. All Right Reserved VALUE auto, shutterpriority, irispriority, qualitypriority, manual, etc SECURITY( get/set) 4/4 (Available options are list in "capability_image_c<0~(n1)>_exposure_modetype") irismode fixed, indoor, outdoor 4/4 piris_mode manual, indoor, outdoor,- 1/4 194 - User's Manual DESCRIPTION "capability_image_c<0~(n1)>_exposure_mode" !=0 Select exposure mode.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( get/set) piris_position 1~100 1/4 enableblc 4/4 maxgain 0~100 4/4 mingain 0~100 4/4 DESCRIPTION 1)>_sensortype" is "smartsensor") * Only available when "capability_image_c<0~(n1)>_iristype"=piris Manual set P-Iris.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY( get/set) gainvalue 0~100 4/4 color 0, 1 4/4 flip mirror rotate 0,90,180,270 4/4 4/4 1/4 ptzstatus 0, 1/7 text string[64] 1/4 196 - User's Manual DESCRIPTION 1)>_exposure_rangetype" is "twovalues". Gain value.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE DESCRIPTION SECURITY( get/set) 4/4 imprinttimesta mp textonvideo_p osition textonvideo_si ze textonvideo_fo ntpath top, bottom 4/4 Text on video string position 20~40 4/4 Text on video font size textonvideo_u ploadfilename minexposure Depends on the font file name uploaded by user <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc. /usr/share/font/Default.ttf 4/4 , /mnt/flash2/upload.
VIVOTEK NAME shuttervalue © 2022 VIVOTEK INC. All Right Reserved VALUE <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE crop_size (x,y) (WxH) SECURITY( get/set) DESCRIPTION 1/7 Crop width and height. (width must be 16x or 32x and height must be 8x) Indicates multiple of zoom in is “onscreen display” or not. * We support this parameter when the version number (httpversion) is equal or greater than 0302a. ⚫ The total available lists (capability_image_c<0~(n1)>_exposure_bracketing_range) will be normalized to 1~100 scale.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE s<0~(m1)>_smartfps_ enable SECURITY( get/set) 4/4 s<0~(m1)>_h264_dint raperiod_enab le 4/4 s<0~(m1)>_h264_intr aperiod s<0~(m1)>_h264_rate controlmode s<0~(m1)>_h264_qua nt 250, 500, 1000, 2000, 3000, 4000 4/4 cbr, vbr 4/4 1~5, 99, 100 4/4 s<0~(m1)>_h264_qval ue 0~51 4/4 s<0~(m1)>_h264_qpe rcent 1~100 4/4 s<0~(m- 20000~"capability_videoin 4/4 200 - User's Manual DESCRIPTION Enable "Smart fps" function.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE 1)>_h264_sma rtq_enable SECURITY( get/set) s<0~(m1)>_h265_dint raperiod_enab le 4/4 s<0~(m1)>_h265_intr aperiod 250, 500, 1000, 2000, 3000, 4000 4/4 s<0~(m1)>_h265_rate controlmode cbr, vbr 4/4 s<0~(m1)>_h265_qua nt 1~5, 99, 100 4/4 s<0~(m1)>_h265_qval ue 0~51 4/4 202 - User's Manual DESCRIPTION * Only available when "capability_videoin_c<0~(n1)>_smartq_support" is 1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( get/set) s<0~(m1)>_h265_qpe rcent 1~100 4/4 s<0~(m1)>_h265_max vbrbitrate 20000~"capability_videoin _c<0~(n1)>_h265_maxbitrate" 4/4 DESCRIPTION s<0~(m-1)>_h265_quant = 99. Select customized quality in a normalized full range. 1: Worst quality 100: Best quality * Only available when h265 is listed in "capability_videoin_codec". * Only valid when "h265_ratecontrolmode"= vbr and "quant"= 100.
VIVOTEK NAME © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE alue "capability_api_httpversio n" format is XXXXX_1 or XXXXX_3 or XXXXX_4 ex: 0301a_1 or 0301a_3 or 0301a_4) or 1~99 (Only valid when "capability_api_httpversio n" format is XXXXX_2, ex: 0301a_2) 1~100 4/4 s<0~(m1)>_mjpeg_qp ercent SECURITY( get/set) DESCRIPTION library directly. * Only valid when "mjpeg_ratecontrolmode"= vbr and s<0~(m-1)>_mjpeg_quant = 99 Select customized quality in a normalized full range.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( get/set) aespeed_mod e 4/4 aespeed_spee dlevel 1~100 4/4 aespeed_sensi tivity 1~100 4/4 flickerless 4/4 mounttype ceiling, wall, floor 1/6 enablewaterm 0, 1 1/6 DESCRIPTION 1)>_wdrc_mode" is 1 Turning AE converge speed on or off.
VIVOTEK NAME ark s<0~(m2)>_fisheyede warpmode © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION video quality of ROI is better than the non-ROI areas. The level is from 1 to 5. Level 5 is the maximum level of the quality difference between the ROI and non-ROI areas. If the value is a negative number, the video quality of non-ROI areas is better than the ROI. The level is from 1 to -5. Level -5 is the maximum level of the quality difference between the ROI and non-ROI areas.
VIVOTEK NAME begintime endtime minexposure © 2022 VIVOTEK INC. All Right Reserved VALUE hh:mm hh:mm <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc. SECURITY (get/set) 4/4 4/4 4/4 * Available value is listed in "capability_image_c<0~(n1)>_exposure_minrange" maxexposure <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) shuttervalue <1~32000>, 4/4 <5~32000>, <1~8000>, <5~8000>, etc. * Available value is listed in "capability_image_c<0~(n1)>_exposure_maxrange" enableblc 4/4 exposurelevel 0~12 4/4 DESCRIPTION "twovalues". Exposure time 1~32000 => 1s ~ 1/32000s 5~32000 => 1/5s ~ 1/32000s 1~8000 => 1s ~ 1/8000s 5~8000 => 1/5s ~ 1/8000s etc.
VIVOTEK NAME exposuremode © 2022 VIVOTEK INC. All Right Reserved VALUE auto, shutterpriority, irispriority, qualitypriority, manual, etc SECURITY (get/set) 4/4 (Available options are list in "capability_image_c<0~(n1)>_exposure_modetype") whitebalance auto, panorama, manual, rbgain, widerange, outdoor, indoor, sodiumauto, etc (Available values are listed in "capability_image_c<0~(n1)>_wbmode") 212 - User's Manual 4/4 DESCRIPTION 10: EV +1.3 11: EV +1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) rgain 0~100 4/4 bgain 0~100 4/4 maxgain 0~100 4/4 mingain 0~100 4/4 DESCRIPTION "outdoor": auto white balance mode specifically for outdoor. "indoor": auto white balance mode specifically for indoor. "sodiumauto": sodium vapor lamps. * Only available when "capability_image_c<0~(n1)>_wbmode" !="-" Manual set rgain value of gain control setting.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) gainvalue 0~100 4/4 meteringmode auto, blc, hlc 4/4 * Available value is listed in "capability_image_c<0~(n1)>_exposure_meteringm ode" piris_mode manual, indoor, outdoor,- 1/4 piris_position 1~100 1/4 214 - User's Manual DESCRIPTION "piris_mode"=manual or "irismode"=fixed * Normalized range. * Only available when "capability_image_c<0~(n1)>_exposure_rangetype" is "twovalues". Gain value.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE e SECURITY (get/set) aespeed_spee dlevel 1~100 4/4 aespeed_sensi tivity 1~100 4/4 flickerless 4/4 DESCRIPTION 0: off 1: on * Only available when "capability_image_c<0~(n1)>_aespeed" is 1 The speed level of AE converge speed.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved ipaddress 4/4 Multicast video IP address. port 1025 ~ 65535 4/4 Multicast video port. ipversion IPv4, IPv6 4/4 The version of internet protocol. ttl 1 ~ 255 4/4 Multicast video time to live value. 7.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE disableirled SECURITY (get/set) 6/6 enableextled 1/6 enablewled 6/6 bwmode 6/6 DESCRIPTION Enable/disable built-in IR led * Only available when " capability_daynight_c<0~"capability_ nvideoin"-1>_builtinir > 0".
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE use this> SECURITY (get/set) sensitivity low,normal,high,1~10 0 6/6 spectrum_mode visible, ir, irenhanced, blueenhanced * Available values are listed in "capability_daynight_ c<0~(n1)>_spectrum_mode" . 6/6 220 - User's Manual DESCRIPTION "capability_daynight_c<0~(n-1)>_ blackwhitemode" is 1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION after the version number (httpversion) is equal or greater than 0400a. 7.10.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved sensitivity low,normal,high,1 ~100 6/6 equal or greater than 0312a. Sensitivity of day/night control. There are two value format: "low,normal,high": if capability_daynight_c<0~(n1)>_ircutsensitivity_type=options "1~100": if capability_daynight_c<0~(n1)>_ircutsensitivity_type=normalize * Only available when "capability_daynight_c<0~(n-1)> _ircutsensitivity_type" is not "-".
© 2022 VIVOTEK INC. All Right Reserved external_do_enabled 1/6 external_do<2~(k)>_ena bled 1/6 spectrum_mode visible, 6/6 ir, irenhanced, blueenhanced * Available values are listed in "capability_daynig ht_illuminators _spectrum_mode" .
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) brightnesspercent 0~100 4/4 contrastpercent 0~100 4/4 saturationpercent 0~100 4/4 sharpnesspercent 0~100 4/4 gammacurve 0~100 4/4 DESCRIPTION "sharpnesspercent". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. Set brightness in the normalized range.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE xoffset 0~100 SECURITY (get/set) 4/4 yoffset 0~100 4/4 lens_alignment 0~100 4/4 DESCRIPTION Adjusting the image to proper position horizontally. * Only available when the bit 4 of capability_image_c<0~(n1)>_basicsetting is 1. Adjusting the image to proper position vertically. * Only available when the bit 5 of capability_image_c<0~(n1)>_basicsetting is 1. Stitch the sensors together into focused position.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE recommended to use this> profile_i<0~(m1)>_contrast profile_i<0~(m1)>_saturation profile_i<0~(m1)>_sharpness SECURITY (get/set) DESCRIPTION * Only available when bit 0 of "capability_image_c<0~(n1)>_basicsetting" is 1 -5~5,100 4/4 * We replace "profile_i0_brightness" with "profile_i0_brightnesspercent".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME profile_i<0~(m1)>_brightnessperc ent VALUE SECURITY (get/set) 0~100 4/4 profile_i<0~(m0~100 1)>_contrastpercen t 4/4 profile_i<0~(m1)>_saturationperc ent 0~100 4/4 profile_i<0~(m1)>_sharpnessperc ent 0~100 4/4 profile_i<0~(m1)>_gammacurve 0~100 4/4 230 - User's Manual DESCRIPTION * We replace "profile_i0_saturation" with "profile_i0_saturationpercent".
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK NAME profile_i<0~(m1)>_dis_strength © 2022 VIVOTEK INC. All Right Reserved VALUE 1~100 SECURITY (get/set) 4/4 DESCRIPTION "capability_image_c<0~(n1)>_is_mode". Strength of digital image stabilizer * Only available when 'dis' is listed in "capability_image_c<0~(n1)>_is_mode". 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME home size VALUE <0~320,0~240> <0~320x0~240> homepx <0~W,0~H> sizepx W: 0~ The current image width 1 H: 0~ The current image height 1 <0~Wx0~ H> homestd W: 0~ The current image width 1 H: 0~ The current image height 1 <0~9999,0~9999> sizestd <0~9999x0~9999> SECURITY (get/set) 4/4 4/4 4/4 4/4 DESCRIPTION listed in "capability_image_c<0~(n1)>_exposure_wintype". Left-top corner coordinate of the window.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE in "capability_image_c<0~(n1)>_exposure_winmode" SECURITY (get/set) DESCRIPTION "auto": Use full view as the only one exposure window. "custom": Use inclusive and exclusive window. "blc": Use BLC(Back Light Compensation), and the only exposure window is located at the center of view. "hlc": Use HLC (High Light Compensation), and to perform the masking of bright light area.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) homepx <0~W,0~H> 4/4 sizepx W: 0~ The current image width 1 H: 0~ The current image height 1 <0~Wx0~ H> homestd W: 0~ The current image width 1 H: 0~ The current image height 1 <0~9999,0~9999> 4/4 sizestd <0~9999x0~9999> 4/4 4/4 DESCRIPTION 1)>_exposure_windomain". Left-top corner coordinate of the window. * Only available when px is listed in "capability_image_c<0~(n1)>_exposure_windomain".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME volume_internal volume_external VALUE 0~100 0~100 SECURITY (get/set) 4/4 4/4 mute 0, 1 1/4 gain 0~100 4/4 boostmic 0~100 236 - User's Manual 4/4 DESCRIPTION is showed on product, this value is updated during booting to fit switch status. Volume when take internal microphone as input source.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE aec_enable alarm_enable alarm_level profile_i0_enable profile_i0_policy 1~100 night, schedule profile_i0_begintime hh:mm profile_i0_endtime hh:mm profile_i0_alarm_lev 1~100 el SECURITY (get/set) 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 DESCRIPTION Enable acoustic echo cancellation. * Only available when "capability_audio_aecmode" is "manual".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved n denotes the value of "capability_naudioout" NAME VALUE SECURITY (get/set) volume 0~100 4/4 DESCRIPTION Adjusting audio volume 7.
VIVOTEK © 2022 VIVOTEK INC.
© 2022 VIVOTEK INC. All Right Reserved NAME VALUE top 0 ~ 240 width 0 ~ 320 height 0 ~ 240 VIVOTEK SECURITY DESCRIPTION (get/set) * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. 4/4 Top coordinate of window position. * Only available when "capability_motion_wintype" = rectangle.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME begintime endtime win_sensitivity VALUE hh:mm hh:mm 0 ~ 100 SECURITY DESCRIPTION (get/set) 4/4 4/4 4/4 * Not support "policy=day" anymore when the version number (httpversion) is equal or greater than 0301a. * "policy=night" is only available when "capability_daynight_c<0~(n1)>_support > 0". Begin time of schedule mode. End time of schedule mode. Sensitivity of all motion detection windows.
© 2022 VIVOTEK INC. All Right Reserved NAME polygon left top width height VIVOTEK VALUE SECURITY DESCRIPTION (get/set) image height -1 * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. 0 ~ 320,0 ~ 240, 0 ~ 4/4 Coordinate of polygon window position.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Only available when "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain". * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE blurry_duration 1~10 SECURITY (get/set) 4/4 DESCRIPTION SECURITY (get/set) 6/6 6/6 DESCRIPTION If image too blurry value exceeds the "threshold" for more than "duration" second(s), then image too blurry detection is triggered. 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.21 UPnP Port Forwarding Group: upnpportforwarding NAME VALUE enable upnpnatstatus 0~3 SECURITY DESCRIPTION (get/set) 6/6 Enable or disable the UPnP port forwarding service. 6/7 The status of UPnP port forwarding, used internally. 0 = OK, 1 = FAIL, 2 = no IGD router, 3 = no need for port forwarding 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE v2 SECURITY (get/set) 6/6 DESCRIPTION v3 6/6 secnamerw string[31] 6/6 SNMP v2 enabled. 0 for disable, 1 for enable SNMP v3 enabled.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE theme_option 1~4 SECURITY (get/set) 1/6 theme_color_font string[7] 1/6 1~3: One of the default themes. 4: Custom definition. Font color theme_color_configfont string[7] 1/6 Font color of configuration area. theme_color_titlefont string[7] 1/6 Font color of video title. theme_color_controlba ckground theme_color_configbac kground theme_color_videoback ground theme_color_case string[7] 1/6 Background color of control area.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.25 Privacy Mask Group: privacymask_c<0~(n-1)> for n channel products and m privacy mask window. n denotes the value of "capability_nvideoin" and m denotes the value of "capability_videoin_c<0~(n-1)>_nprivacymask" NAME VALUE SECURITY (get/set) enable 4/4 DESCRIPTION Enable privacy mask. win_i<0~(m-1)>_enable 4/4 Enable privacy mask window. win_i<0~(m-1)>_name string[14] 4/4 Name of the privacy mask window.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME win_i<0~(m1)>_polygonpx win_i<0~(m1)>_polygonstd VALUE SECURITY (get/set) 0 ~ W,0 ~ H, 4/4 0 ~ W,0 ~ H, 0 ~ W,0 ~ H, 0 ~ W,0 ~ H W: 0~ The current image width -1 H: 0~ The current image height -1 0 ~ 9999,0 ~ 4/4 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999 DESCRIPTION "capability_image_c_privacymask _wintype" = polygon. * Only available when qvga is listed in "capability_image_c<0~(n1)>_privacymask_windomain".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) 1)>_maxpan" win_i<0~(m-1)>_tilt "capability_ptz_c<0~(n1)>_mintilt" ~ "capability_ptz_c<0~(n1)>_maxtilt" "capability_ptz_c<0~(n1)>_minzoom" ~ "capability_ptz_c<0~(n1)>_maxzoom" win_i<0~(m-1)>_zoom win_i<0~(m-1)>_fliped 4/4 4/4 4/4 DESCRIPTION "capability_camctrl_c<0~(n1)>_buildinpt" is "1" Tilt position of window position.
VIVOTEK NAME api_logoversion © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) DESCRIPTION distinguish between different platforms API version format: MMmmr_k Where "MM" is the major version, "mm" is the minor version and "r" is the revision. 'M' and 'm' and 'k' are decimal digit from 0 to 9, while 'r' is an alphabetic.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION 0/7 Number of virtual inputs (manual trigger) Number of digital outputs. nvideoin 0, 0, 0, 0, nvideoout nvi ndo naudioin 0/7 0/7 The number of audio input channel. 0 means no audio input support. The number of audio output channel 0/7 Number of video inputs.
VIVOTEK NAME © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME npreset VALUE 0, SECURITY (get/set) 0/7 presettourdirection 0/7 eptz 0/7 0, DESCRIPTION use this. * This is reserved for compatibility and will not be used after the version number (httpversion) is equal or greater than 0400a. * We replace "capability_remotefocus" with " capability_image_c0_remotefocus". Number of preset locations Indicate whether to support preset tour direction function.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION "visignal" = Video input signal loss. "backup" = Backing up recorded files. "smartsd" = Lifetime detection of SD card. "shockalarm" = Shock detection. "virestore" = Video input signal restore. "presetreached" = When any preset is reached "casingopen" = Casing open detection. * Only available when [httpversion] >= 0301a Number of media number.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE protocol_rtp_http SECURITY (get/set) 0/7 protocol_spush_mj peg protocol_snmp 0/7 0/7 Indicate whether to support RTP over HTTP. Indicate whether to support server push MJPEG. Indicate whether to support SNMP. protocol_ipv6 0/7 Indicate whether to support IPv6. protocol_pppoe 0/7 Indicate whether to support PPPoE.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK NAME audio_mic 260 - User's Manual © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) 0/7 DESCRIPTION The format is "Affect API name":"Policy":"Description" "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION camctrl_privilege 0/7 uart_httptunnel 0/7 transmission_mod e 0/7 network_wire Tx, Rx, Both 0/7 "capability_camctrl_c0_ptztunnel". * This is kept for compatibility. * Only available when capability_ptzenabled > 0 Indicate whether to support “Manage Privilege” of PTZ control in the security page. 1: support both /cgibin/camctrl/camctrl.cgi and /cgibin/viewer/camctrl.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) localstorage_modn um 0, 0/7 localstorage_modv ersion 0/7 localstorage_storm grversion 0/7 localstorage_suppo 0, rtedge 0/7 localstorage_slcon num 0, 0/7 localstorage_smart sd 0/7 DESCRIPTION One bit represents one channel. Ex: “3” means channel 0 and channel1 support seamless recording .
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) remotecamctrl_ma ster 0, 0/7 remotecamctrl_sla ve fisheyelocaldewarp _c<0~(capability_n videoin)-1> 0/7 0, 0/7 shockalarm_suppo rt 0/7 layout_redirection 0/7 securecam_suppor t 0/7 securecam_version 0/7 268 - User's Manual DESCRIPTION card's remaining lifetime information.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE taics_support SECURITY (get/set) 0/7 taics_level 0, 0/7 cameralink_suppor t 0/7 cameralink_num 0, 0/7 cameralink_version 0/7 DESCRIPTION Support the feature for Video Surveillance System Security from TAICS. * We support this parameter when the version number (httpversion) is equal or greater than 0314b.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE privilege SECURITY (get/set) 0/7 rs485 0/7 buildinpt 0/7 zoommodule 0/7 270 - User's Manual DESCRIPTION Indicate whether to support “Manage Privilege” of PTZ control in the security page in this video input. 1: support both /cgibin/camctrl/camctrl.cgi and /cgibin/viewer/camctrl.cgi 0: support only /cgibin/viewer/camctrl.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER focusmode digitalzoom_support VALUE SECURITY (get/set) auto,onetimeauto,sp 0/7 otlight,manual 0/7 DESCRIPTION Focus mode selection: "auto": Camera will automatically adjust the focus position full time to adapt a clear picture. "onetimeauto": Camera will automatically adjust the focus position one time, which follows any PTZ control.
VIVOTEK PARAMETER © 2022 VIVOTEK INC. All Right Reserved minpan SECURITY (get/set) 0, 0/7 maxpan 0, 0/7 minpanangle 0/7 maxpanangle 0/7 tiltspeedlv 0, 0/7 mintilt 0, 0/7 maxtilt 0, 0/7 mintiltangle 0/7 maxtiltangle 0/7 zoomspeedlv 0, 0/7 272 - User's Manual VALUE DESCRIPTION The lower limit for pan position.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE minzoom SECURITY (get/set) 0, 0/7 maxzoom 0, 0/7 maxdzoom 0, 0/7 focusspeedlv 0, 0/7 minfocus 0, 0/7 maxfocus 0, 0/7 DESCRIPTION The lower limit for zoom position. *Only available when the value of "capability_camctrl_c<0~(n1)>_zoommodule" is "1" The upper limit for zoom position.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE builtinwled externalir optimizedir smartir SECURITY DESCRIPTION (get/set) 0/7 Indicate whether to support built-in white led. * We replaced this parameter with “capability_daynight_illuminators_builti n_type=whiteled” when the version number (httpversion) is equal or greater than 0312a. 0/7 Indicate whether to support external IR led.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE ircutsensitivity_type ircutsensitivity_supportle 0, vel extled_interface do VIVOTEK SECURITY DESCRIPTION (get/set) 0/7 Indicate the cgi interface of "ircutcontrol_sensitivity". "options": the value of "ircutcontrol_sensitivity" parameter is "low, normal,high".
VIVOTEK PARAMETER spectrum_support spectrum_mode 276 - User's Manual © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) 0/7 Indicate whether to support proposed a brightness enhancement method based on CCM(Color Correction Matrix) model to improve the brightness effect of the images if the IR and blue light exists.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER mode VIVOTEK VALUE SECURITY DESCRIPTION (get/set) auto,daynight,di,di2, 0/7 Indicate the day / night switch mode. di3,di4,schedule,"auto": The Camera automatically the level of ambient light detected. "daynight": support day mode and night mode. In day mode, the camera streams color video. In night mode, the camera streams black and white video in low light environments.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved builtin_type irled,whiteled, 0/7 external_support 0/7 external_interface do,do2,do3,do4 0/7 * Available values are do, do<2~(capability_nd o)> spectrum_support 278 - User's Manual 0/7 Indicate whether to support built-in led type. "irled": IR led "whiteled": white led "-": not support * We support this parameter when the version number (httpversion) is equal or greater than 0312a.
© 2022 VIVOTEK INC. All Right Reserved spectrum_mode visible,ir,irenhanced, 0/7 blueenhanced VIVOTEK Indicate the spectrum mode. "visible": The ideal default setting for visible light. "ir": The ideal default setting for IR light. "irenhanced": This CCM model increases the brightness effect of IR light. "blueenhanced": This CCM model increases the brightness effect of blue light.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Group: capability_videoin_c<0~(n-1)> n denotes the value of "capability_nvideoin" PARAMETER VALUE SECURITY DESCRIPTION (get/set) lens_type fisheye, fixed, 0/7 The lens type of this channel. varifocal, "fisheye": Fisheye lens changeable, "fixed": Build-in fixed-focus lens. motor, ics,"varifocal": Build-in varifocal lens. type camera, users can install any C-Mount or CS-Mount lens as they wish.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE rotationaffect rotationangle SECURITY (get/set) 0/7 0/7 VIVOTEK DESCRIPTION When rotation is enabled, some features may become malfunction or be forced to a given value. The affected functions are list here. The format is "Affect API name":"Policy":"Description" "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it.
VIVOTEK PARAMETER orientation © 2022 VIVOTEK INC.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER maxframerate VALUE SECURITY (get/set) A list of 0/7 mjpeg_maxframerate A list of and "-" mjpeg_maxbitrate , - 0/7 VIVOTEK DESCRIPTION Indicate frame rate that the video source outputs in current video mode. One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER h264_maxframerate VALUE SECURITY (get/set) A list of and "-" h264_maxbitrate 0/7 h264_profile baseline,main,hig 0/7 h h265_maxframerate A list of and "-" h265_maxbitrate 0/7 DESCRIPTION Maximum fps that the device can encoded with H.264 on resolutions in current video mode. "-" means not support.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY (get/set) 0/7 h265_profile main,main10 fisheye_mounttype ceiling, wall, floor 0/7 mounttype ceiling, wall, 0/7 floor,_mounttype " dintraperiod_support 0/7 cameraunit_name CU8131, CU8171, CU8161-H, CU8162-H, CU8163-H, CU8361-H, ...
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE cmosfreq_support SECURITY (get/set) 0/7 smartfps_support 0/7 smartq_support 0/7 DESCRIPTION 0: The power line frequency(50/60Hz) is detected by camera automatically. 1: The power line frequency(50/60Hz) can be set by user. * We support this parameter when the version number (httpversion) is equal or greater than 0308a. Indicate whether to support Smart fps function.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE panorama_pancontrol VIVOTEK SECURITY DESCRIPTION (get/set) 0/7 Indicate whether to support localdewarp panorama pan control. * We support this parameter when the version number (httpversion) is equal or greater than 0312b. 7.27.
VIVOTEK PARAMETER eptz wdrpro effectivepixel 288 - User's Manual © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) 0, 0/7 Indicate this mode whether support eptz. For "nvideoin" = 1, the definition is as following: A 32-bits integer, each bit can be set separately as follows: Bit 0 => 1st stream supports ePTZ or not. Bit 1 => 2nd stream supports ePTZ or not, and so on.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE outputsize binning 0, 1, 3 nresolution resolution A list of maxresolution A list of minresolution A list of VIVOTEK SECURITY DESCRIPTION (get/set) 0/7 The output size of source, equal to the captured size by device, in this video mode. The unit is pixel. This value is used as a basic coordinate system for many features, like ePTZ, privacy mask, motion, etc.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE maxframerate A list of maxfps_mjpeg A list of and "-" maxfps_h264 A list of and "-" 290 - User's Manual SECURITY DESCRIPTION (get/set) 0/7 Indicates frame rate that the video source outputs in this video mode. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE maxfps_h265 A list of and "-" description VIVOTEK SECURITY DESCRIPTION (get/set) 0/7 Maximum fps which the device can encoded with H.265 on resolutions in this video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) wdrpro_supportlevel 0, wdrpro_affect -, 0/7 exposurewin.mode :fixed:auto, exposurelevel:hidd en:, exposurelevel:fixed :, exposurelevel:fixed :/, exposuremode:fixe d:auto, gammacurve:disabl ed:, exposurewin.mode .blc:hidden:, exposurewin.mode .
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) wdrpro_description 0/7 wdrc_mode 0, 1 0/7 wdrc_supportlevel 0, -, 0/7 gammacurve:disabl ed:, : nonnegative integer wdrc_affect DESCRIPTION For example: "exposurelevel:fixed:6/8/12" which means exposurelevel is fixed to level 6, level 8 and level 12. "-" means no feature is affected. * When "wdrpro"=0, this value must be "-" Description about WDR Pro mode.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) dnr 0,1 0/7 dnrstrength 0/7 dnrtype 2d,3d 0/7 eis 0,1 0/7 is_mode eis, dis, - 0/7 is_strength 0/7 294 - User's Manual DESCRIPTION integer or string or NULL. For example: "exposurelevel:fixed:6/8/12" which means exposurelevel is fixed to level 6, level 8 and level 12. "-" means no feature is affected.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) is_supportlevel 0, 0/7 is_affect -, : nonnegative integer 0/7 DESCRIPTION equal or greater than 0302a. Indicate the support strength level of image stabilizer mode. * Only available when "capability_image_c<0~(n1)>_is_mode" is not "-". * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME scenemode_support VALUE 0,1 scenemode_supportty visibility, pe noiseless, lpcparkinglot, lpcstreet, lpchighway, auto, deblur, lpcfreeway, signallight, railtrack scenemode_signalligh -, t_affect flickerless:unchang ed:, wdrpro:unchanged : SECURITY (get/set) 0/7 0/7 0/7 DESCRIPTION the version number (httpversion) is equal or greater than 0302a.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL. scenemode_railtrack_ affect -, flickerless:unchang ed:, wdrpro:unchanged : 0/7 "-" means no feature is affected.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME wbmode VALUE SECURITY (get/set) auto, panorama, manual, rbgain, widerange, outdoor,indoor, sodiumauto, piris, dciris, - 0/7 sensortype rawsensor, smartsensor, thermalsensor, - 0/7 exposure_mode 0,1 0/7 exposure_modetype auto, shutterpriority, irispriority, manual 0/7 exposure_rangetype onevalue, twovalues 0/7 iristype 298 - User's Manual 0/7 DESCRIPTION integer or string or NULL.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME exposure_shuttervalu etype exposure_gainvaluety pe VALUE fixed, maximum, ranged, - fixed, maximum, ranged, - SECURITY (get/set) 0/7 0/7 DESCRIPTION "twovalues": Need two parameters to indicate the exposure range. * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0302a. * One to one mapping to the mode type in "exposure_modetype".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME exposure_automode_ affect 300 - User's Manual VALUE -, exposurewin.mode .blc:hidden:, defog:disabled:, wdrpro:disabled:, exposurelevel:hidd en:, defaultgain:fixed:x or others : nonnegative integer SECURITY (get/set) 0/7 DESCRIPTION "shutterpriority" is listed in "capability_image_c<0~(n-1)>_ exposure_modetype" and "capability_image_c<0~(n-1)>_ exposure_mode" is 1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE exposure_shutterprior -, itymode_affect exposurewin.mode .blc:hidden:, defog:disabled:, wdrpro:disabled:, exposurelevel:hidd en:, defaultgain:fixed:x or others : nonnegative integer SECURITY (get/set) 0/7 DESCRIPTION exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE exposure_irispriority mode_affect -, exposurewin.mode .blc:hidden:, defog:disabled:, wdrpro:disabled:, exposurelevel:hidd en:, defaultgain:fixed:x or others : nonnegative integer exposure_qualityprior itymode_affect -, exposurewin.mode .
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE wdrpro:disabled:, exposurelevel:hidd en:, defaultgain:fixed:x or others : nonnegative integer exposure_manualmod -, e_affect exposurewin.mode .blc:hidden:, defog:disabled:, wdrpro:disabled:, exposurelevel:hidd en:, icrmode.auto:nots SECURITY (get/set) 0/7 DESCRIPTION are list here.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE upport: or others : nonnegative integer SECURITY (get/set) exposure_levelrange -, "0,12" 0/7 exposure_winmode auto, custom, blc, hlc, center, 0/7 304 - User's Manual DESCRIPTION following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE exposure_meteringm ode exposure_hlcmode_s upportwindow exposure_hlcmode_af fect SECURITY (get/set) auto, blc, hlc 0/7 -, sir:hidden: or others : nonnegative integer 0/7 0/7 DESCRIPTION value must be set to "-". * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) exposure_wintype inclusive, exclusive, - 0/7 exposure_windomain qvga, px, std, - 0/7 exposure_winnum 0, 0/7 exposure_ntsc_totalra A list of 306 - User's Manual 0/7 DESCRIPTION "Description" can be a nonnegative integer or string or NULL. "-" means no feature is affected.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) exposure_pal_totalra nge A list of 0/7 exposure_maxrange "1,32000", "1,8000", -, or others 0/7 exposure_minrange "1,32000", "1,8000", -, or others 0/7 exposure_bracketing_ mode 0/7 DESCRIPTION exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0301a.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) exposure_bracketing_ range A list of ratio For example: 2x,3x,4x 0/7 privacymask_wintype rectangle, polygon, 3Drectangle 0/7 privacymask_windom ain qvga, px, std, - 0/7 privacymask_ncolor 0/7 agc_maxgain "0,100", "-" 0/7 agc_mingain "0,100", "-" 0/7 flickerless 0,1 0/7 308 - User's Manual DESCRIPTION * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE flickerlessaffect -, minexposure.lower bound:fixed:x or others : nonnegative integer defog_mode 0,1 0/7 defog_strength 0, 1 0/7 defog_supportlevel 0, -, 0/7 defog_affect SECURITY (get/set) 0/7 0/7 DESCRIPTION When flickerless is enabled, some features may become malfunction or be forced to a given value. The affected functions are list here.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE wdrc:unchanged: contrast:hidden: or others : nonnegative integer SECURITY (get/set) aespeed 0,1 0/7 aespeedsupportlevel 0/7 aespeedsupportsensit ivity 0,1 0/7 310 - User's Manual DESCRIPTION may become malfunction or be forced to a given value. The affected functions are list here.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) gammacurve 0,1 0/7 lowlightmode -,0,1 0/7 focusassist 0,1 0/7 remotefocus 0, 0/7 focuswindomain qvga, px, std, - 0/7 focuswindow_nwindo w focuswindow_range 0, 0,1 0/7 lensconfiguration_sup port freeze 0/7 DESCRIPTION "capability_image_c<0~(n1)>_aespeed" is 1.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) palette_mode A list of palette options 0/7 focussystem_mode AFbyzoom, focusshift, 0/7 DESCRIPTION The color tones correspond to the apparent surface temperatures of the target. * We support this parameter when the version number (httpversion) is equal or greater than 0310a. Palette options used in thermal surveillance. *Only available when "capability_image_c<0~(n1)>_palette_support"=1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE devicemonitor_tempnu m devicemonitor_heatern um 7.27.11 SECURITY (get/set) 0/7 0/7 Number of temperature sensors that can be monitored. * Only available when "capability_peripheral_c<0~(n1)>_devicemonitor_support" > 0 Number of sensor sensors that can be monitored.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE name string[40] SECURITY DESCRIPTION (get/set) 6/6 Identification of this entry. enable 0, 1 6/6 Enable or disable this event.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE mdwin 0, mdwin0 0, vi 0, vadp 0, valevel 0,1 valevel0 0,1 inter 1~999 weekday 0~127 316 - User's Manual SECURITY DESCRIPTION (get/set) 6/6 Indicate the source window id of motion detection. This field is required when trigger condition is “md”. One bit represents one window. The LSB indicates the 1st window.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE begintime hh:mm SECURITY DESCRIPTION (get/set) 6/6 Begin time of the weekly schedule. endtime hh:mm 6/6 lowlightcondition 0, 1 6/6 action_do_i<0~(k1)>_enable 6/6 action_do_i<0~(k1)>_duration 1~999 6/6 action_cf_enable 6/6 action_cf_folder string[128] 6/6 End time of the weekly schedule.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE foldername string[128] action_cf_media NULL, 0~4,101 action_cf_datefolder action_cf_backup action_server_i<0~4>_en able action_server_i<0~4>_m edia action_server_i<0~4>_da tefolder action_goto_enable SECURITY DESCRIPTION (get/set) 6/6 Path to store media.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE action_autotrack_name string[40] VIVOTEK SECURITY DESCRIPTION (get/set) 6/6 Indicate the source name of smart tracking advanced when an event is triggered. * Only avaliable when the bit4 of capability_ptzenabled is 1 and the bit7 of capability_ptzenabled is 0, and the camera supports “Smart Tracking Advanced” feature.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE tampering 0, action_cameralink_id SECURITY DESCRIPTION (get/set) 6/6 Indicate the source channel id of tampering detection. A 4-bit integer, each bit represents each channel. bit 0 => tampering detection for first channel. bit 1 => tampering detection for second channel. bit 2 => tampering detection for third channel. bit 3 => tampering detection for fourth channel.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE ftp_passwd string[64] SECURITY DESCRIPTION (get/set) 7/6 Password of the user. ftp_port 0~65535 6/6 Port to connect to the server. ftp_location string[128] 6/6 Location to upload or store the media. ftp_passive 6/6 email_address string[128] 6/6 Enable or disable passive mode. 0 = disable passive mode 1 = enable passive mode Email server address. email_sslmode 6/6 Enable support SSL.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved loginmode passwd, publickey 6/6 username passwd port location fingerprint_enable string[64] string[64] 0~65535 string[128] boolean 6/6 7/6 6/6 6/6 6/6 fingerprint_content <128-bit hash value> 6/6 publickey_pairmode auto, download, upload 6/6 publickey_downloadkeytype ed25519, rsa, ecdsa 6/6 publickey_passphrase_enable boolean 6/6 publickey_passphrase_content string[128] 7/6 authentication method: ”passwd” = password authentication.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE Type snapshot, systemlog, videoclip, recordmsg 0~"capability_nvideoin"-1 snapshot_channel SECURITY DESCRIPTION (get/set) 6/6 Media type to send to the server or store on the server.
VIVOTEK PARAMETER © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) videoclip_channel 0~"capability_nvideoin"-1 6/6 Indicate the source of media channel. 0 means the first channel. 1 means the second channel. 2 means the third channel. 3 means the fourth channel. * We support this parameter when the version number (httpversion) is equal or greater than 0311c. videoclip_source 0~"capability_nmediastream 6/6 Indicate the source of media "-1 stream. 0 means the first stream.
© 2022 VIVOTEK INC. All Right Reserved VIVOTEK PARAMETER VALUE trigger schedule, networkfail enable SECURITY DESCRIPTION (get/set) 6/6 The event trigger type schedule: The event is triggered by schedule networkfail: The event is triggered by the failure of network connection. 6/6 Enable or disable this recording.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE notifyserver 0~31 weekday 0~127 begintime hh:mm SECURITY DESCRIPTION (get/set) 6/6 Indicate which notification server is scheduled. One bit represents one application server (server_i0~i4). bit0 (LSB) = server_i0. bit1 = server_i1. bit2 = server_i2. bit3 = server_i3. bit4 = server_i4. For example, enable server_i0, server_i2, and server_i4 as notification servers; the notifyserver value is 21. 6/6 Indicate which weekday is scheduled.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE maxduration 60~3600 adaptive_enable adaptive_preevent 0~9 adaptive_postevent 0~10 recordingjob_Sourc string[64] eToken_Token SECURITY DESCRIPTION (get/set) 6/6 Unit: Second When this condition is reached, recording file is truncated.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE organizationname string[64] VIVOTEK Inc. unit string[64] VIVOTEK Inc. commonname string[64] www.vivotek.com validdays 0 ~ 825 SECURITY (get/set) 6/6 6/6 6/6 6/6 DESCRIPTION Organization name in the certificate information. Organizational unit name in thecertificate information. Common name in the certificate information. Valid period for the certification. 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY (get/set) 6/6 autocleanup_enabled autocleanup_maxage 6/6 DESCRIPTION Enable automatic clean up method. Expired and not locked media files will be deleted. * For forward compatibility reservations, but only group disk_i0_autocleanup is effective. * Not recommended to use this. Please refers "autocleanup" group.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.34 Region of Interest Group: roi_c<0~(n-1)> for n channel product and m is the index of video stream which support ePTZ. (capability_eptz > 0) PARAMETER s<0~(m-1)>_home s<0~(m-1)>_size VALUE SECURITY (get/set) 1/6 1/6 DESCRIPTION ROI left-top corner coordinate.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION -5 ~ 5 SECURITY (get/set) 1/7 tiltspeed panspeed -5 ~ 5 1/7 Pan speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) zoomspeed -5 ~ 5 1/7 Zoom speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) autospeed 1~5 1/7 Auto pan/patrol speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) Tilt speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) 7.35.1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE preset_i<0~19>_size SECURITY (get/set) 1/7 DESCRIPTION Width and height of the preset. (It should be set by ePreset.cgi rather than by setparam.cgi.) 7.36 Focus Window Setting Group: focuswindow_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin".
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY (get/set) 1/6 diskmode seamless, manageable maxconnection 3 1/7 enable 1/7 VIVOTEK DESCRIPTION “seamless” indicates enable seamless recording. “manageable” indicates disable seamless recording. * We replace this parameter with “seamlessrecording_c<0~(n-1)>_diskmode” when the version number (httpversion) is equal or greater than 0312a. * We do not support this parameter when "capability_nvideoin > 1".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE guid<0~2>_id string[127] SECURITY (get/set) 1/7 guid<0~2>_number 0~3 1/7 DESCRIPTION The connected seamless streaming ID. (Read only) * We replace this parameter with “seamlessrecording_c<0~(n1)>_guid<0~2>_id” when the version number (httpversion) is equal or greater than 0312a. * We do not support this parameter when "capability_nvideoin > 1".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved triggerrecord 1/7 guid<0~(k-1)>_id string[127] 1/7 guid<0~(k-1)>_number 0~3 1/7 Indicate whether seamless recording is recording to local storage or not at present. (Read only) * We support this parameter when the version number (httpversion) is equal or greater than 0312a. The connected seamless streaming ID.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE number string[128] status developer_mode string[40] SECURITY DESCRIPTION (get/set) upload it. If the value is false, save module to the internal storage space and it will occupy storage size. * This feature is not supported when "capability_securecam_support=1" and the version number of "capability_securecam_version" < "1.0.1.0" 6/7 This number is used to register license key for VADP application.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) name extendedname string[40] string[40] 6/6 6/6 url string[120] 6/6 vendor vendorurl version license string[40] string[120] string[40] string[40] 6/6 6/6 6/6 6/6 licmsg string[128] 6/6 path initscr string[40] string[40] 6/7 6/7 status string[40] 6/6 statmsg string[128] 6/6 vvtklicensemec string[40] 6/7 DESCRIPTION If yes, also add the index of this module to the module_order.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.38.4. VADP Event Settings Group: vadp_event NAME VALUE ntrigger 0, triggerlist_i<0~(n1)>_topic string[256] SECURITY (get/set) 6/7 6/6 DESCRIPTION Indicate the number of topics to be transferred to event manager for trigger. Indicate the event notification with this topic will be transferred to event manager as trigger. n is equal to ntrigger above. 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) cameraid 0~255 1/4 isptz 0~2 1/4 disablemdonptz 1/4 DESCRIPTION capability_camctrl_c0_rs485=2 Camera ID controlling external PTZ camera. 0: disable PTZ commands. 1: enable PTZ commands with PTZ driver. 2: enable PTZ commands with UART tunnel. * only available when capability_camctrl_c0_rs485=2 Disable motion detection on PTZ operation. 7.
VIVOTEK NAME uart © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) values are listed in "capability_cam ctrl_c<0~(n1)>_focusmode " 0~ 1/4 "capability_nua rt"-1 DESCRIPTION preset_i<0~(k-1)>_name string[40] preset_i<0~(k-1)>_zoom capability_ptz_ c<0~(n1)>_minzoom ~ capability_ptz_ c<0~(n1)>_maxzoom preset_i<0~(k-1)>_focus capability_ptz_ c<0~(n1)>_minfocus ~ capability_ptz_ c<0~(n1)>_maxfocus preset_i<0~(k-1)>_ 0 ~ 999 dwelling 1/4 1/4 Select corresponding uart (capability_nuart>0).
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION disablemdonptz 1/4 defaulthome 1/4 axisz 1/4 1/4 Custom home focus position.
VIVOTEK NAME panspeed tiltspeed zoomspeed autospeed focusspeed focusmode © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) DESCRIPTION preset_i<0~(k-1)>_fliped patrol_i<0~39>_name string[40] 1/4 1/4 patrol_i<0~39>_ dwelling 0 ~ 999 1/4 disablemdonptz 1/4 defaulthome 1/4 axisx 1/4 1/4 Custom home tilt position. 1/4 Custom home zoom position. 1/4 Custom home focus position.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) tour_index -1, 0~19 1/4 tour_i<0~19>_name tour_i<0~19>_type string[40] 1/4 1/4 tour_i<0~19>_speed -5 ~ 5 1/4 tour_i<0~19>_direction forward,backward,ra ndom 1/4 tour_i<0~19>_checklist string[512] 1/4 tour_i<0~19>_dwelltim e string[512] 1/4 tour_i<0~19>_enabletra ck 1/4 DESCRIPTION enhancement Index of the enabled tour group, from 0 to 19. Set -1 to disable all the tour groups.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.42 UART Control Group: uart (capability_nuart > 0 and capability_fisheye = 0) NAME VALUE SECURITY DESCRIPTION (get/set) ptzdrivers_i<0~19, string[40] 1/4 Name of the PTZ driver. 127>_name ptzdrivers_i<0~19, string[128] 1/4 Full path of the PTZ driver. 127>_location enablehttptunnel 1/4 Enable HTTP tunnel channel to control UART.
VIVOTEK NAME © 2022 VIVOTEK INC. All Right Reserved VALUE SECURITY (get/set) 128 (no driver) DESCRIPTION * only available when capability_camctrl_c0_rs485=2 7.43 UART Control (SD Series) Group: uart_i<0~(n-1)> n is uart port count (capability_nuart > 0 and the bit7 of capability_ptzenabled is 0, the bit4 of capability_ptzenabled is 1) NAME VALUE SECURITY DESCRIPTION (get/set) cameraid 1~255 4/4 Camera ID controlling external PTZ camera.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Group: uart_i<0~(n-1)> n is uart port count (capability_nuart > 0 and capability_ibis = 1) NAME VALUE SECURITY DESCRIPTION (get/set) baudrate 1200,2400,4800,960 4/4 Set baud rate of COM port. 0,19200,38400 databit 5,6,7,8 4/4 Data bits in a character frame. paritybit stopbit none, odd, even 1,2 4/4 For error checking. 4/4 "1": One stop bit is transmitted to indicate the end of a byte. "2": Two stop bits are transmitted to indicate the end of a byte.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Group: lens_default_i<0~(n-1)> n denotes the value of "lens_default_totalnumbers" NAME VALUE SECURITY (get/set) name 6/7 DESCRIPTION Default lens name Group: lens_user_i<0~(n-1)> n denotes the value of "lens_user_totalnumbers" NAME VALUE SECURITY (get/set) name 6/7 DESCRIPTION User-defined lens name 7.46 Fisheye Info.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY (get/set) s<0~(m2)>_region_zoom s<0~(m2)>_region_r<0~(i1)>_pan 100~300 1/4 -90~359 1/4 s<0~(m2)>_region_r<0~(i1)>_tilt -90~90 1/4 s<0~(m2)>_region_r<0~(i1)>_zoom 100~300 1/4 DESCRIPTION Tilt range of wall mount is [-90~90]. Zoom home ratio of regional view (for 1R mode) Pan home angle of regional view (for 4R mode, i is the view index and range from 0 to 3) Pan range of ceiling/floor mount is [0~359].
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE sensitivity 0~2 SECURITY (get/set) 1/4 DESCRIPTION Tracking sensitivity. 0: Low 1: Medium 2: High 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE key2 password [26] SECURITY (get/set) 6/6 key3 password [26] 6/6 key4 password [26] 6/6 algorithm AES, TKIP 6/6 presharedkey password [64] 6/6 DESCRIPTION WEP key2 for encryption. * Only valid when "wireless_encrypt" is "wep" WEP key3 for encryption. * Only valid when "wireless_encrypt" is "wep" WEP key4 for encryption.
VIVOTEK © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 7.53 Multicast Settings for Metadata Streaming Group: metadata_c<0~(n-1)>_s0_multicast (capability_media_streamprofiles_support = 1) n denotes the value of "capability_nvideoin" NAME VALUE ipaddress SECURITY( get/set) 4/4 DESCRIPTION port 1025 ~ 65535 4/4 Multicast metadata port. ipversion IPv4, IPv6 4/4 The version of internet protocol. ttl 1 ~ 255 4/4 Multicast metadata time to live value. Multicast metadata IP address. 7.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER gotopreset_enable gotopreset_type gotopreset_index gotopreset_channel gotopreset_stream VALUE SECURITY DESCRIPTION (get/set) 6/6 Enable the PTZ preset function of the receiving camera. mechanical, digital 6/6 PTZ type of the receiving camera. 0, 0, 0, 6/6 PTZ preset index of the receiving camera. 6/6 PTZ preset channel of the receiving camera.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VIVOTEK VALUE SECURITY DESCRIPTION (get/set) focusshift_day_lastdate , 6/7 A recorded UTC time when IR offset value : IR offset value hasn't been saved before. focusshift_night_position , 6/7 A customized IR offset value in lens profile when ICR is switched to night mode. : default IR offset value is used.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8. Useful Functions 8.1 Drive the Digital Output (capability_ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/dido/setdo.cgi?do0= [&do1=] [&do2=][&do3=] Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state, and trigger time is indicated in seconds.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Content-Type: text/plain\r\n Content-Length: \r\n \r\n [di0=]\r\n [di1=]\r\n [di2=]\r\n [di3=]\r\n where can be 0 or 1. Example: Query the status of digital input #1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di0 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di0=1\r\n 8.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do0=1\r\n 8.4 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/video.jpg?[channel=][&resolution=] [&quality=][&streamid=] If the request contains invalid parameters, a full FOV snapshot will return.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved [Content-Length: \r\n] 8.5 Account Management Note: This request requires Administrator privileges. Method: POST Syntax: http:///cgi-bin/admin/editaccount.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Response of success: HTTP/1.1 200 OK\r\n Content-Type: text/html\r\n Content-Length: 2\r\n \r\n Response of failure: HTTP/1.1 200 OK\r\n Content-Type: text/html\r\n Content-Length: \r\n \r\n List of error message: ERROR: Add user fail! ERROR: Delete user fail! ERROR: Update user's password fail! ERROR: Update user's privilege fail! 8.6 Upgrade Firmware Note: This request requires Administrator privileges.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.7 ePTZ Camera Control (capability_eptz > 0 and Capability_fisheye = 0) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/eCamCtrl.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zooming=tele&zs=1 http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zooming=wide&zs=5 zooming is used to indicate the moving direction, and zs is used to indicate the speed. To stop a continuous movement, you have to use the command as below: http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zoom=stop&zs=0 2.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER h VALUE DESCRIPTION resolution The resolution of streaming. vx The direction of movement, used for joystick control. vy vs 0~7 Set the speed of movement, “0” means stop. x y videosize x-coordinate clicked by user. It will be the x-coordinate of center after movement. y-coordinate clicked by user. It will be the y-coordinate of center after movement.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.8 ePTZ Recall (capability_eptz > 0 and capability_fisheye = 0) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/eRecall.cgi?channel=&stream=& recall=[&return=] PARAMETER channel VALUE <0~(n-1)> DESCRIPTION Channel of the video source. stream <0~(m-1)> Stream. recall Text string less than 40 characters One of the present positions to recall.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER delpos VALUE DESCRIPTION return Redirect to the page after the parameter is assigned. The should be the relative path according to the root of camera. If you omit this parameter, it will redirect to an empty page. * If the is invalid path, it will ignore this parameter. 8.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved x-sessioncookie: string[22] accept: application/x-vvtk-tunnelled pragma: no-cache cache-control: no-cache ------------------------------------------------------------------------POST /cgi-bin/operator/uartchannel.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved x-sessioncookie: string[22] content-type: application/x-vvtk-tunnelled pragma : no-cache cache-control : no-cache content-length: 32767 expires: Sun, 9 Jam 1972 00:00:00 GMT User must use GET and POST to establish two channels for downstream and upstream. The xsessioncookie in GET and POST should be the same to be recognized as a pair for one session. The contents of upstream should be base64 encoded to be able to pass through the proxy server.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.14 Open the Network Stream Note: This request requires Viewer access privileges. Syntax: For HTTP push server (MJPEG): http:///_accessname> For RTSP (MP4), the user needs to input theURL below into an RTSP compatible player. rtsp:///_accessname> “m” is the stream number. For details on streaming protocol, please refer to the “control signaling” and “data format” documents. 8.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Content-Length: \r\n \r\n \r\n Where hexadecimal data is digits from 0 ~ 9, A ~ F. 8.16 Storage Managements (capability_storage_dbenabled > 0) Method: GET and POST Note: This request requires administrator privileges. In the past time, all the recorded files could be searched/updated/deleted independently. However, this implementation provides no abstraction of recorded video clips, and which is not easy to use.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER resolution VALUE isLocked triggerTime limit offset DESCRIPTION Optional. Indicate the media file resolution. Please embrace your input value with single quotes. Ex. resolution=’800x600’ Optional. Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage. Optional. Indicate the event trigger time.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http:///cgi-bin/admin/lsctrl.cgi?cmd=queryStatus&retType=javascript There are two cgi commands for download and composing jpegs to avi format. For download single selected file, you can use “/cgi-bin/admin/downloadMedias.cgi”. Just assign the request file path to this cgi. Syntax: http:///cgi-bin/admin/downloadMedias.cgi? The is in queryststus return message. Ex. http:///cgibin/admin/downloadMedias.
VIVOTEK PARAMETER resolution fps list © 2022 VIVOTEK INC. All Right Reserved VALUE x DESCRIPTION Resolution Frame rate The JPEG file list. The file path should be embraced by single quotation marks Ex. http:// /cgi-bin/admin/ jpegtoavi.cgi?resolution=800x600&fps=1&list=’/mnt/auto/CF/NCMF/video1650.jpg’, ’/mnt/auto/C F/NCMF/video1651.jpg’, ’/mnt/auto/CF/NCMF/video1652.jpg’, 8.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 503 No multiple duration. setvi.cgi?vi3=0 VI index is out of range. setvi.cgi?vi=1 No VI index is specified. The resource is unavailable, ex. Virtual input is waiting for next state. Examples: setvi.cgi?vi0=0(15000)1 setvi.cgi?vi0=1 Request 2 will not be accepted during the execution time(15 seconds). 8.18 Open Timeshift Stream (capability_timeshift > 0, timeshift_enable=1, timeshift_c_s_allow=1) Note: This request requires Viewer access privileges.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE DEFAULT reftime mm:ss The time camera receives the request. forcechk N/A N/A minsft 0 Return Code 400 Bad Request 415 Unsupported Media Type DESCRIPTION (normal, adaptive), unknown parameters are always ignored. Reference time for maxsft and minsft. (This provides more precise time control to eliminate the inaccuracy due to network latency.) Ex: Request the streaming from 12:20 rtsp://10.0.0.1/live.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE function zoom, focus, auto, scan, stop, positioning, irisopen, irisenable DESCRIPTION zoom - Move focus motor focus – Move focus motor auto – Perform auto focus scan – Perform focus scan stop – Stop current operation positioning – Position the motors irisopen – Fully open iris. It will maintain fully open iris status until sending function=irisenable cgi. irisenable – return back to user setting status of iris.
VIVOTEK function © 2022 VIVOTEK INC.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER function VALUE focus, auto, scan, stop, positioning, irisopen, irisenable, resetfocus DESCRIPTION focus – Move focus motor auto – Perform auto focus scan – Perform focus scan stop – Stop current operation positioning – Position the motors resetfocus – reset focus position to default irisopen – Fully open iris. It will maintain fully open iris status until sending function=irisenable cgi. irisenable – return back to user setting status of iris.
VIVOTEK function © 2022 VIVOTEK INC. All Right Reserved getstatus Information of motors, return value as below: remote_focus_focus_motor_max: Maximum steps of focus motor remote_focus_focus_motor_start: Start point of effective focal length remote_focus_focus_motor_end: End point of effective focal length remote_focus_focus_motor: Current position of focus motor remote_focus_focus_enable: Current function of focus motor remote_focus_iris_open: The current status of iris.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http:///cgi-bin/admin/export_backup.cgi?backup 8.22 Upload Files Note: This request requires Administrator privileges. Method: POST Syntax: For daylight saving time configuration file: * This CGI is not supported when the version number (httpversion) is equal or greater than 0314b, please use “system_tz” as a replacement. http:///cgi-bin/admin/upload_dst.cgi Post data: filename =\r\n \r\n For l
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Note: This request requires Administrator privileges. Method: GET Syntax: For list a name of lens currently used: http:///cgi-bin/admin/update_lens.cgi?get_currentlens For list all names of lens installed in camera: http:///cgi-bin/admin/update_lens.cgi?list_lens For choose selected lens configuration: http:///cgi-bin/admin/update_lens.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.24 Media on Demand (capability_localstorage.modnum > 0) Media on demand allows users to select and receive/watch/listen to metadata/video/audio contents on demand. Note: This request requires Viewer access privileges. Syntax: rtsp:///mod.sdp?[&stime=][&etime=][&length =][&loctime =][&file=][&tsmode=] PARAMETER stime etime length VALUE DEFAULT N/A
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.25 3D Privacy Mask (Capability_image_c<0~(n1)>_privacymask_wintype = 3Drectangle) n denotes the value of "capability_nvideoin" Note: This request requires admin user privilege Method: GET/POST Syntax: http:///cgibin/admin/setpm3d.
© 2022 VIVOTEK INC. All Right Reserved VIVOTEK 8.26 Camera Control (capability_camctrl_c<0~(n1)>_zoommodule = 1) Note: This request requires Viewer privileges. Method: GET/POST Syntax: (for control API) http:///cgi-bin/camctrl/camctrl.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE right DESCRIPTION Move camera right. speedpan -5 ~ 5 Set the pan speed. speedtilt -5 ~ 5 Set the tilt speed. speedzoom -5 ~ 5 Set the zoom speed. speedfocus -5 ~ 5 Set the focus speed. speedapp -5 ~ 5 Set the auto pan/patrol speed. auto pan Auto pan. patrol Auto patrol. stop Stop camera. wide Zoom larger view with current speed. tele Zoom further with current speed. stop Stop zoom.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER cam VALUE fixcurrent DESCRIPTION Applies the current focus position to this preset. * We support this function when the version number of the PTZ control module is equal or greater than 5.0.0.20. getsetpreset Adds a named preset at current position, and return the preset index. * We support this function when the version number of the PTZ control module is equal or greater than 5.0.0.20.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER getminspeedlv VALUE DESCRIPTION 0, Get the minimum speed level of the PTZ control. Normally, the speed level is ‘0,’ which denotes halting a continuous movement. getmaxptspeedlv 0, Get the maximum speed level of pan/tilt moving. *Only available when "capability_camctrl_c<0~(n1)>_buildinpt" > 0 getmaxzspeedlv 0, Get the maximum speed level of zoom moving.
© 2022 VIVOTEK INC. All Right Reserved VIVOTEK 8.27 Recall (capability_camctrl_c<0~(n-1)>_zoommodule = 1) Note: This request requires Viewer privileges. Method: GET Syntax: http:///cgi-bin/viewer/recall.cgi? recall=[&channel=][&return=] PARAMETER recall VALUE string[30] DESCRIPTION One of the present positions to recall. channel 0~" Channel of the video source.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.28 Preset Locations (capability_camctrl_c<0~(n1)>_zoommodule = 1) Note: This request requires Operator privileges. Method: GET/POST Syntax: http:///cgi-bin/operator/preset.cgi?[channel=] [&addpos=][&delpos=][&return=] PARAMETER addpos VALUE string[30] DESCRIPTION Add one preset location to the preset list. channel 0~"capability_nvideoin"- Channel of the video source.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER function VALUE getstatus DESCRIPTION Function type getstauts : Information of smartSD internal status return value as below: smartsd_lifetime_num: Accumulated amount of data that has been written smartsd_lifetime_den: Card-guaranteed amount of data that can be written smartsd_lifetime_rate: The ratio of smartsd_lifetime_num to smartsd_lifetime_den. It means the accumulated percentage amount of flash block has been written.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.31 Get Wireless Information (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/getwirelessinfo.cgi PARAMETER N/A VALUE N/A DESCRIPTION Get wireless information. Camera will return following information. 1. Wireless channel 2. Link quality 3. Signal level 4. Noise level 5. SNR 6. TX Rate 7. RX Rate 8.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER N/A VALUE N/A DESCRIPTION Get wireless signal strength. 8.33 WPS Transaction (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/start_wps.cgi PARAMETER N/A VALUE N/A DESCRIPTION Start WPS transaction. 8.34 Peripheral Control (capability_peripheral_c<0~(n-1)>_ devicecontrol > 0) Note: This request requires Administrator privileges.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER channel washer_mode VALUE 0~"capability_nvideoin"-1 wiper washer washer_status on off washer_dwelltime 15~999 heater_status auto trigger DESCRIPTION Channel of the video source. Apply the wiper to the mode of washer control system. Apply the washer to the mode of washer control system. Enable the functionality of washer control system. Disable the functionality of washer control system.
© 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE washer_status N/A washer_dwelltime N/A heater_supportstatus N/A heater_status N/A VIVOTEK DESCRIPTION It return the value of "washer_mode" Get the current status of washer control module. The status is 'off' as default, which means the washer is stopped; and the status 'on' means the washer is running. Get the current washer clean period of washer control system. Get the support status of heater control system. Get the current heater status.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.35 Device monitor (capability_peripheral_c<0~(n-1)>_ devicemonitor_support > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/devicemonitor.cgi PARAMETER N/A VALUE N/A DESCRIPTION Return a status overview of all sensors and peripheral devices on camera.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http://myserver/cgi-bin/admin/devicemonitor.cgi Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n devicemonitor_tempsensor_i0_name=front glass devicemonitor_tempsensor_i0_celsius=30 devicemonitor_tempsensor_i0_fahrenheit=86 devicemonitor_heater_i0_name=front glass devicemonitor_heater_i0_status=off 8.36 Optimized IR control (capability_daynight_c<0~(n1)>_optimizedir > 0) Note: This request requires Administrator privileges.
VIVOTEK PARAMETER function © 2022 VIVOTEK INC. All Right Reserved VALUE getstatus, onetimeauto DESCRIPTION "onetimeauto": Camera will automatically adjust the IR zone one time only. "getstatus": Information of optimized IR control status and return value as below: optimizedir_c<0~(n-1)>_irmode: Indicate the IR current mode, available value is “auto” and “manual” mode. optimizedir_c<0~(n-1)>_irnum: The number of IR that camera supports.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION operation set, settoall "set": set the strength of each IR LED separately "settoall": use fixed strength for all IR LED irmode auto, manual 1~100 Irmode needs to be set as manual for adjusting IR LED strength. If the operation is set as "set", the number of strength values need to be the same as it of irnum. However, it needs only one value for strength when the operation is set as "settoall".
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http://myserver/cgibin/admin/optimizedir.cgi?channel=0&operation=set&irmode=auto&strength=50,70,50,50,50 Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n ERROR: Parameter "irmode" must be set as "manual"! Example: http://myserver/cgi-bin/admin/optimizedir.cgi?channel=0&operation=set&strength=50,70,50,50,50 Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n ERROR: Must have the "irmode=manual
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved http://myserver/cgi-bin/admin/optimizedir.cgi?channel=0&operation=get&irmode Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n "optimizedir_c0_irmode='auto'" 8.37 Lens Thermal Control (capabiltiy_image_c<0~(n1)>_sensortype=thermalsensor) Note: This request requires Administrator privileges. Method: GET/POST Syntax: (for control API) http:///cgi-bin/admin/thermalctrl.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n ERROR: fail PARAMETER action VALUE shuttercompensate DESCRIPTION Camera will do shutter compensate. Syntax: (for query API) http:///cgi-bin/admin/thermalctrl.cgi?operation=get&version= PARAMETER version VALUE N/A DESCRIPTION Indicate lensctrl thermal version Example: http://myserver/cgi-bin/admin/thermalctrl.cgi?operation=get&version Response: HTTP/1.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved name index 0, 1 "download" = Download a clip to the client. * Recording time is limited to 60 seconds. Name of the audio clip. The audio clip the action applies to. We support two interfaces (name or index) to specify the media clip to be played. Number of the audio clip. The audio clip the action applies to. We support two interfaces (name or index) to specify the media clip to be played.
VIVOTEK index © 2022 VIVOTEK INC. All Right Reserved 0~N at the start of the format which one SD card Example: Request of format SD card: http://myserver/cgi-bin/admin/format_sdcard.cgi?operation=set&fstype=ext4 Response of success: HTTP/1.1 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 2\r\n \r\n ok Response of formatting fail: HTTP/1.1 200 OK\r\n Content-Type: text/plain\r\n Content-Length: \r\n \r\n Syntax: (for query API) http:///cgi-bin/a
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved ERROR: You cannot format an SD card repeatedly ERROR: Format SD failed, but removed all contents success ERROR: Format SD failed, and failed to remove all contents ERROR: Please insert SD card ERROR: Please use ext file system ERROR: File system type is not supported ERROR: The device does not exist or is busy ERROR: Formatted successfully, but cannot create database 8.40 Methods for Accessing Streaming 8.39.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved 8.39.2 Get SDP for always multicast (capability_media_streamprofiles_support = 1) Note: This request requires Viewer access privileges. Method: GET/POST Syntax: http://:/media2/_profilename>.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Syntax: (for control API) http:///cgi-bin/admin/sftpclient.cgi?operation=[¶meter=] PARAMETER VALUE DESCRIPTION operation automode, manualmode "automode": Key pair will be generated, and automatically copy public key to server. "manualmode": Key should be downloaded or uploaded by user. key address download, upload * This field is required. "download": Download public key.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved key=upload. location string[128] sftp server file location name string[40] Username for server_i_name keytype ed25519, rsa, ecdsa * The default value is sftp. "ed25519": faster to generate with higher security level, some old server might not support. "rsa": slower to generate with slightly lower security level than ed25519. "ecdsa": low security level. A keytype will be automatically selected if the parameter is not provided.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Content-Type: multipart/form-data; boundary=---------------------------7e1309282ed0f1a Accept-Encoding: gzip, deflate Host: 172.16.219.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved -----END RSA PRIVATE KEY---------------------------------7e1309282ed0f1a-- Syntax: (for query API) http:///cgi-bin/admin/sftpclient.cgi?operation=[¶meter=] PARAMETER VALUE DESCRIPTION operation getserverhostkey " getserverhostkey ": Auto scan SFTP server host key. address * This field is required. sftp server address or hostname * This field is required.
VIVOTEK © 2022 VIVOTEK INC. All Right Reserved Example of re-generate host key: Request: http:///cgi-bin/admin/sftpserver.cgi?operation=updatehostkey Response of success: HTTP/1.1 200 OK\r\n Content-Type: text/plain\r\n Content-Length: \r\n \r\n ok Syntax: (for query API) http:///cgi-bin/admin/sftpserver.cgi?operation= PARAMETER VALUE DESCRIPTION operation gethostkey "gethostkey": Get host key for SFTP server. * This field is required.
VIVOTEK Technology License Notice AMR-NB Standard THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING LICENSORS’ PATENTS MAY APPLY: TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938; 6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION: AT PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621; DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT.
VIVOTEK Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. ■ This device may not cause harmful interference, and ■ This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
