MODELS MODELS // E3D320VX // E3D420VX // E3D470VX E321VT USER GUIDE INSTALLING YOUR new TV CONTROLS & CONNECTIONS CONNECTING YOUR DEVICES USING THE ON-SCREEN MENU USING THE USB MEDIA PLAYER TROUBLESHOOTING & SUPPORT SPECIFICATIONS, SAFETY & LEGAL
This product qualifies for ENERGY STAR in the “factory default” setting and this is the setting in which power savings will be achieved. Changing the factory default picture settings or enabling other features will increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR rating. ® SRS Sound Solutions is a trademark of SRS Labs, Inc. Sound Solutions technologies is incorporated under license from SRS Labs, Inc. Manufactured under license from Dolby Laboratories.
Welcome Thank You for Choosing VIZIO Important Safety Instructions And congratulations on your new VIZIO HDTV. Your TV is designed and manufactured to operate within defined design limits. Misuse may result in electric shock or fire. To prevent your TV from being damaged, the following instructions should be observed for the installation, use, and maintenance of your TV. Read the following safety instructions before operating your TV. Keep these instructions in a safe place for future reference.
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel.
Opening or removing the back cover may expose you to high voltages, electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to qualified service personnel. • WARNING: Keep your TV away from moisture. Do not expose your TV to rain or moisture. If water penetrates into your TV, unplug the power cord and contact your dealer. Continuous use in this case may result in fire or electric shock. • Do not use your TV if any abnormality occurs.
DTV Transition Advisory The nationwide switch to digital television broadcasting was complete on June 12, 2009. Analog-only television sets that receive TV programming through an antenna now need a converter box to continue to receive over-the-air TV. Watch your local stations to find out when they will turn off their analog signal and switch to digital-only broadcasting.
Television Antenna Connection Protection If an outside antenna/satellite dish or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges.
Table of Contents Installing the TV................................................. 3 Adjusting the Audio Settings............................................... 19 Inspecting the Package Contents...................................... 3 Enabling or Disabling SRS TruSurroundHD........................ 19 Installing the TV.................................................................... 3 Enabling or Disabling SRS TruVolume............................... 20 Installing the TV Stand....................
Blocking and Unblocking Content by Rating................... 30 Changing the Parental Control Passcode....................... 31 Resetting the Content Locks............................................. 31 Viewing System Info and Resetting to Factory Defaults...... 31 Displaying System Information......................................... 31 Restoring the TV to the Factory Default Settingss............. 32 Restarting the Setup App.................................................
1 Installing the TV Inspecting the Package Contents Installing the TV Before installing your new TV, take a moment to inspect the package contents. Use the images below to ensure nothing is missing or damaged. After removing the TV from the box and inspecting the package contents you can begin installing the TV.
PC AUDIO COMPONENT (BETTER) Y/V Pb/Cb Pr/Cr RGB PC 1 DTV/TV L AUDIO R CABLE/ANTENNA Installing the TV on a Wall To mount your TV on a wall, you will need a wall mount. Consult the information below to find the appropriate mount for your TV model: Installing a TV on a wall requires lifting. To prevent injury or damage to the TV, ask someone to help you. E321VT Screw Size: Screw Length: Screw Pitch: Hole Pattern: M4 20mm 0.
2 Controls and Connections Rear Panel AUDIO OUT Optical Audio Out - Connect optical/SPDIF audio device, such as home audio receiver. OPTICAL Stereo Audio Out - Connect 3.5mm cable to audio device, such as sound bar. AUDIO OUT USB USB - Connect USB thumb drive to play photo slideshow or to update firmware. HDMI 3 - Connect HDMI device. HDMI (BEST) 3 HDMI 2 - Connect HDMI device. 2 HDMI 1 - Connect HDMI device. This port is compatibile with Audio Return Channel (ARC).
2 Front Panel REMOTE SENSOR When using the remote, aim it directly at this sensor.
2 Remote Control Input Change the currently-displayed input. Power Turn TV on or off. A/V Controls Control USB photo viewer. Info Display the info window. Closed Captions Open the closed caption menu. Menu Display the on-screen menu. Exit Close the on-screen menu. Arrow Navigate the on-screen menu. Ok Select the highlighted menu option. V Button Open the USB photo viewer. Back Go to the previous on-screen menu. Channel Up/Down Change the channel.
2 Replacing Batteries Replacing the Batteries 1. Remove the battery cover. 2. Insert two batteries into the remote control. Make sure that the (+) and (-) symbols on the batteries match the (+) and (-) symbols inside the battery compartment. 3. Replace the battery cover. • Use only good quality batteries. • Inserting the batteries incorrectly may result in cracking or leakage that may cause a fire or result in injury.
3 Connecting Your Devices Connecting A Device Your TV can be used to display output from most devices. 1. Verify that your device has a video port that matches an available port on the TV (HDMI, Component, etc). AUDIO OUT 2. Turn the TV and your device off. Cable/Satellite Box OPTICAL 3. Connect the appropriate cable (not included) to the TVAUDIO and OUT the device. 4. Turn the TV and your device on. Set the TV’s input to match the connection you used (HDMI-1, HDM1-2, etc).
3 Connecting A PC Your TV can be used to display output from a personal computer. To use your TV as a PC display: AUDIO OUT 1. Connect an RGB cable (not included) to your PC and the RGB port on the back of the TV. This cable transmitsOPTICAL video. 2. Connect a 3.5mm cable (not included) to your PC and the PC Audio In port on the back of the TV. This cable transmits AUDIO OUT audio. 3. Set your PC’s resolution to match the resolution of your TV. See Appendix B - Specifications.
3 Connecting an Audio Device Your TV can output sound to an audio device, such as a receiver or sound bar. 1. Verify that your device has a audio port that matches an available port on the TV (Optical, etc). Home Audio Receiver 2. Turn the TV and your audio device off. 3. Connect the appropriate cable (not included) to the TV and the device. 4. Turn the TV and your device on. VIZIO Sound Bar Optical/SPDIF Cable AUDIO OUT BETTER OPTICAL AUDIO OUT GOOD USB 3.
4 Completing the First-Time Setup 4. Select Home Mode. The first time you turn on the TV, the Setup App will guide you through each of the steps necessary to get your TV ready for use. Press the Right Arrow button to go to the next screen. Before you begin the first-time setup: • Your TV should be installed and the power cord should be connected to an electrical outlet. • Your devices should be connected. 5. Use the Arrow buttons to highlight the input source that is delivering your TV signal.
5 Using the On-Screen Menu Your TV features an easy-to-use on-screen menu. Navigating the On-Screen Menu Using this menu, you can: To open the on-screen menu, press the MENU/OK button on the remote. • Change the input source • Change the screen aspect ratio • Set up closed captioning • Activate the sleep timer • Adjust the picture settings • Adjust the audio settings • Change TV settings Use the Arrow buttons to highlight a menu option, and press the MENU/OK button to select that option.
5 Changing the Input Source Changing the Screen Aspect Ratio External devices such as DVD players, Blu-Ray Players, and video game consoles can be connected to your TV. To use one of these devices with your TV, you must first change the input source in the on-screen menu. The TV can display images in four different modes: Wide, Zoom, Normal, and Stretch. Each mode displays the picture differently. To change the input device: 1. Press the MENU button on the remote.
5 Setting Up Closed Captioning Changing the Appearance of Digital Closed Captions Digital closed captions can be displayed according to your preference. Your TV can display closed captions for programs that include them. Closed captions display a transcription of a program’s dialogue. To change the appearance of digital closed captions: 1. From the Closed Caption menu, use the Arrow buttons to highlight Digital CC Style.
5 Activating the Sleep Timer Adjusting the Picture Settings When activated, the TV’s sleep timer will turn the TV off after a set period of time. Using the Picture menu, you can adjust the following settings: • Change the picture mode To use the sleep timer: • Adjust noise reduction 1. Press the MENU button on the remote. The on-screen menu is displayed. • Enable or disable Fast Response • Enable or disable the ambient light sensor • Reset the picture mode settings 2.
5 • Retail - Sets the picture settings to values that produce a brighter, more vivid picture. Color Temperature - Changes the “warmness” or “coolness” of the white areas of the picture. • Photo - Optimizes the picture settings for viewing photo slideshows. Flesh tones should appear more natural. Reset Picture Setting - Restores custom picture settings to the factory defaults.
5 Enabling or Disabling Fast Response Enabling or Disabling the Ambient Light Sensor Enabling the Fast Response setting can often improve PC and console gaming experiences. When enabled, the ambient light sensor detects the light levels in the room to optimize the brightness of the TV’s backlight. To enable or disable Fast Response: When the ambient light sensor is enabled, you will be unable to manually change the TV’s brightness settings. 1. Press the MENU/OK button on the remote.
5 Adjusting the Audio Settings Resetting the Picture Settings To restore the TV’s picture settings to the factory defaults: Using the Audio Settings menu, you can adjust the following: 1. Press the MENU/OK button on the remote. The on-screen menu is displayed. • Enable or disable SRS TruSurroundHD™ • Enable or disable SRS TruVolume® • Adjust the equalizer settings • Adjust bass and treble levels • Adjust speaker balance 3.
5 Enabling or Disabling SRS TruVolume Adjusting the Equalizer Settings SRS TruVolume intelligently normalizes volume fluctuations due to television commercials or channel changes. Your TV features six preset equalizer settings. These settings allow you to customize your TV’s sound to match the type of programming you most often enjoy. To enable or disable SRS TruVolume: The Equalizer Settings menu is not available when SRS TruSurroundHD is enabled. 1. Press the MENU/OK button on the remote.
5 Adjusting Bass and Treble Levels Adjusting the Speaker Balance The bass and treble levels for your TV’s built-in speakers can be adjusted to your liking. The built-in speakers can be adjusted to distribute the sound between the left and right speakers. To adjust the speaker balance: To adjust the bass and treble levels, you must disable SRS TruSurroundHD and change the Equalizer Settings to Off. To adjust the bass and treble levels: 1. Press the MENU/OK button on the remote.
5 Enabling or Disabling the Built-In Speakers Changing the Audio Language Using this menu option, you can turn the built-in speakers on or off. This is often used when the TV is connected to a home audio system. Some digital free-to-air and cable channels broadcast programs in more than one language. The TV’s MTS (Multichannel Television Sound) feature allows you to listen to audio in your preferred language.
5 Changing the TV Settings Resetting the Audio Settngs To reset the audio settings to the factory default settings: From the TV Settings Menu, you can: 1. Press the MENU/OK button on the remote. The on-screen menu is displayed. 2. Use the Arrow buttons to highlight Audio and press MENU/OK. • Set up channels • Change the on-screen menu language • Change the TV’s date and time • Adjust the TV settings for use with a PC Customizing and Removing Input Names 3.
5 Setting Up Channels 5. Use the Arrow buttons on the remote to highlight the input source you wish to rename, then press MENU/OK. From the channel menu you can: 6. Use the Arrow buttons to highlight Input Naming and press MENU/OK. The on-screen keyboard is displayed. 7. Use the Arrow and MENU/OK buttons to spell the custom input name. When you are finished, highlight OK and press MENU/OK. 8. Press EXIT.
5 Customizing the Master Channel List Scanning for New or Additional Channels By customizing the master channel list, you can choose which channels can be displayed. When a new channel becomes available in your area, you do not have to rescan all channels to add the new channel. Using the add channel feature, you can restrict the scan to new channels only. 1. Press the MENU button on the remote. The on-screen menu is displayed. This is useful because your master channel list settings are preserved. 2.
5 Scanning for Channels Customizing Channel Names Before the TV can detect and display channels and their associated information, you must scan for channels. A channel scan may also be necessary when the TV has been moved to an area where different free-to-air broadcast television channels are available. Your TV features the ability to customize channel names, making them easy to identify. (Custom names have a 10-character limit.) For example, KBOT-DT could be renamed as Favorite.
5 Changing the On-Screen Menu Language Setting the TV’s Date and Time Your TV can display the on-screen menu in different languages. From the Date & Time menu, you can: To change the on-screen menu language: • Set the time zone 1. Press the MENU button on the remote. The on-screen menu is displayed. • Adjust the time for daylight savings • Enable or disable automatic date and time updates • Set the current date and time 2.
5 Adjusting the Time for Daylight Savings Enabling or Disabling Automatic Date and Time Updates This setting will automatically adjust the time for zones which recognize daylight savings time. The current date and time is broadcast digitally in many areas. Your TV can automatically set the time and date using this information. To enable or disable the daylight savings adjustment: When this setting is enabled, you cannot manually set the date and time. 1. Press the MENU button on the remote.
5 Adjusting the TV Settings for Use with A PC Setting the Date and Time Using this menu option, you can manually set the TV’s date and time. Your TV can be used to display output from a home computer using the RGB port. To manually set the date and time: These settings are only available when viewing content from the RGB port. 1. Press the MENU button on the remote. The on-screen menu is displayed. To adjust the PC settings: 2.
5 2. Highlight the channel you want to lock or unlock and press OK. If you would like the TV to automatically adjust the picture for best quality, select Auto Sync and press MENU/OK. Setting the Parental Controls 3. When a channel is locked, the Lock icon appears locked. The channel is not accessible unless the parental passcode is entered. The TV’s parental controls allow you to prevent the TV from displaying certain channels or programs without a password. 4.
5 Viewing System Info and Resetting to Factory Defaults highlight the rating type and press OK. 3. When the rating type is blocked, the Lock icon appears locked. Content with this rating cannot be viewed. You can use the TV’s Help menu to: 4. When the rating type is unblocked, the Lock icon appears unlocked. Content with this rating can be viewed. 5. If you want to block all unrated content, highlight Block Unrated Shows and use the Arrow buttons on the remote to select On.
5 Restoring the TV to the Factory Default Settingss Restarting the Setup App All of the on-screen menu settings can be reset to the factory defaults. The TV’s Setup App can be used to easily set up the TV tuner. To access the Setup App: If you restore the TV to the factory default settings, all changes you have made to the settings will be lost! 1. Press the MENU button on the remote. The on-screen menu is displayed. To restore the TV to its factory default settings: 2.
6 Using the USB Media Player Using the USB Media Player Viewing a USB Photo Slideshow To play a Photo Slideshow, you must first save your images onto a USB thumb drive. AUDIO OUT The USB Media Player allows you to connect a USB thumb drive to your TV and play music or photos.
6 Current Folder Displays the folder path. Folder Contents This area displays the contents of the currently selected folder. You can browse between files using the Arrow and OK buttons on the remote. Image 01 Photo 01/01 Image 01 Pause Press the Pause button on the remote control if you would like to pause the Photo Slideshow. Previous Next Next Press the Play button on the remote control if you would like to start the Photo Slideshow.
Troubleshooting & Technical Support A do you have questions? LET US HELP! YOUR PRODUCT INCLUDES FREE LIFETIME TECH SUPPORT The VIZIO support team is highly trained and is based in the United States. We can help with: • New Product Setup • Connecting Your Devices • Technical Problems • And More Phone: (877) 878-4946 (TOLL-FREE) Email: techsupport@VIZIO.com Web: www.VIZIO.
A The TV displays “No Signal.” There is no sound. • Press the INPUT button on the remote control to select a different input source. • Press Volume Up on the remote control. • If you are using cable TV, satellite, or antenna connected directly to the TV, scan for channels. See Scanning for Channels on page 25. • Press the MUTE button on the remote to ensure mute is off. • Check the audio settings. See Adjusting the Audio Settings on page 19 Ensure the speakers are set to On.
A The picture is distorted. • Nearby electrical devices may be interfering with the TV. Separate the TV from electrical appliances, cars, or flourescent lights. • Ensure all cables are securely attached. When I change input source, the display image changes size. The display image does not cover the entire screen. • If you are in RGB mode (computer), ensure that H-Size and V-Position in the on-screen menu are set correctly.
B Specifications E321VT Screen Size: Diagonal Viewable: Dimensions w/ Stand: w/o Stand: Weight w/ Stand: w/o Stand: TV Type: Refresh Rate: Maximum Resolution: Pixel Pitch: Dynamic Contrast Ratio: RGB Inputs: 32” Class 1 31.51” OSD Language: English, Spanish, French 29.52 x 20.79 x 7.80” 29.52 x 18.84 x 1.57” Audio Outputs: Optical, Stereo 3.5mm Number of Speakers 19.07 lbs 17.64 lbs Watts/Channel Edge-Lit LED 60 Hz 1366 x 768 100,000:1 8.
C Limited Warranty ON PARTS AND LABOR Covers units purchased as new in United States and Puerto Rico Only. VIZIO provides a warranty to the original purchaser of a new Product against defects in materials and workmanship for a period of one (1) year of non-commercial usage and ninety (90) days of commercial use. If a Product covered by this warranty is determined to be defective within the warranty period, VIZIO will either repair or replace the Product at its sole option and discretion.
D Legal & Compliance FCC Class B Radio Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MODELS // E3D320VX // E3D420VX // E3D470VX © 2012 VIZIO INC. All rights reserved.