USER MANUAL M50-D1, M55-D0, M60-D1, M65-D0, M70-D3, & M80-D3
Safety Information IMPORTANT SAFETY INSTRUCTIONS - M-SERIES DISPLAY Your display is designed and manufactured to operate within defined design limits. Misuse may result in electric shock or fire. To prevent your display from being damaged, the following instructions should be observed for the installation, use, and maintenance of your display. Read the following safety instructions before operating your display. Keep these instructions in a safe place for future reference.
IMPORTANT SAFETY INSTRUCTIONS - XR6 TABLET REMOTE Read all the safety information below before using your VIZIO XR6 Tablet Remote. For additional information, read the User Manual available directly through an application in your Tablet Remote. DRIVING SAFELY Use of your Tablet Remote while driving may cause distractions and may be prohibited in some places. Always comply with local laws and regulations when driving.
Table of Contents Getting Started.........................................................5 M-Series Display................................................................................ 5 Overview - Front.......................................................................... 5 Overview - Back........................................................................... 6 Basic Remote..................................................................................... 7 Overview..........................
Getting Started M-SERIES DISPLAY Overview - Front Remote Sensor & Power Indicator When using the Basic Remote, aim it directly at this sensor. The power indicator lights up when the Display turns on, then goes out after several seconds. To keep the power indicator LED on as long as the Display is on, see Turning the Power Indicator On or Off on page 64.
1 Overview - Back 2 3 1 Power Button 1 Volume Up/Down Buttons Input Button USB 2.0 Ports 2 Component Ports HDMI Port Optical/SPDIF Audio Out Port HDMI Ports 3 RCA Audio Out Ports Ethernet Port Note: The image shown here is for illustrative purposes only and may be subject to change.The actual number of ports and their locations may vary, depending on the model.
1 BASIC REMOTE Overview Use the Basic Remote to control the basic functions of the M-Series Display. Input Change the currently displayed input. Power Turn the Display on or off. Link Activate pairing mode. Aspect Ratio Cycle through the different aspect ratio modes. Volume Up/Down Increase/decrease the loudness of the audio. Channel Up/Down (Between Display and Tablet Remote) (Not supported) Picture Mode Cycle through the different picture modes. Mute Turn the audio on or off.
1 TABLET REMOTE Overview The 6″ Android Tablet Remote brings the way you interact up to speed with the rest of your entertainment experience. Simply tap, swipe, or use voice controls to access a virtually limitless library of casting content. Power/Sleep/Wake Headphone port Top Volume buttons Left Front USB port Bottom Charging Your Tablet Remote is charged and ready for you to use.
1 Basic Tablet Remote Gestures The 6″ Android Tablet Remote brings the way you interact up to speed with the rest of your entertainment experience. A few hand gestures are all you need to access a virtually limitless library of casting content.
1 Basic Android Functions There are a few basic functions that you should be familiar with before diving any deeper into the Android Tablet Remote. Power/Sleep/Wake button Press and hold the power button for a few seconds to power on the tablet. To turn off or reboot the tablet, press and hold the power button for a few seconds. A dialogue box appears, giving you the option to Power off or Reboot the tablet. Volume buttons Press the volume buttons to increase and decrease the audio levels of the tablet.
1 Android Quick Settings Use the Quick Settings menu to easily access frequently used settings such as Wi-Fi, Bluetooth, and brightness controls. To access the Quick Settings menu, swipe down from the top of the screen with two fingers (or twice with one finger). Display brightness Slide the icon to lower or increase the brightness of your screen. Left to lower, right to increase. Wi-Fi network Tap the icon to turn Wi-Fi on or off. Tap the Wi-Fi network name to open the Wi-Fi settings menu.
1 Organizing your Android Home screens Change your wallpaper, add a widget, or change screen order by touching and holding the background of any Home screen. You can have an unlimited number of Home screens to the right. To add a new screen, swipe to the rightmost screen and drag an app or widget to the right edge of the screen. (The screen to the left of the main Home screen is only for Google Now) To create a folder, simply drag and drop one app over another on a Home screen.
First-Time Setup 2 Welcome to VIZIO SmartCast! Your new VIZIO Home Theater Display™ is part of the all-new collection of home theater displays, sound bars and home audio speakers that can all be controlled by one ingenious app: the VIZIO SmartCast app. With the app, you can browse movies, TV shows, music and more from multiple sources or apps in one view, without having to switch back and forth between those apps or sources.
2 PAIRING THE TABLET REMOTE WITH M-SERIES DISPLAY Need help installing the Display? Refer to the printed Quick Start Guide (included) for detailed instructions on how to install your new M-Series Display. You can also find a digital copy on support.vizio.com. 1. Turn on the M-Series Display by pressing the Power button on the back of the Display or by pressing the Power button on the Basic Remote Control. Turn on the Tablet Remote by pressing and holding the Power button for a few seconds.
2 4. The tablet begins to search for a wireless network to connect to. Select your wireless network from the list and enter your password. 5. Use the tablet to name your M-Series Display. 6. Take a moment to read the VIZIO Terms of Service and Privacy Policy, as well as Google’s Terms of Service and Privacy Policy. When you are done, tap NEXT to continue.
2 7. Use the tablet to register your M-Series Display. If you do not wish to register, tap Skip in the lower left corner. 8. Use the tablet to sign into your existing Google account. If you do not have one, tap Or create a new account to create a new account. Follow the on-screen instructions to complete the First-Time Setup. 9. The First-Time setup is complete. The VIZIO SmartCast™ App is displayed.
VIZIO SmartCast App ™ 3 The VIZIO SmartCast™ app lets you swipe or use voice search to find your favorite content, across multiple apps and even live TV* together in one simply aggregated screen, making it easy to discover and enjoy movies, shows, music and more. REGISTER FOR A MYVIZIO ACCOUNT 1. Launch the VIZIO SmartCast™ app. 2. Tap Create an Account to register for a MyVIZIO account. Follow the on-screen instructions to complete the registration process.
3 NAVIGATING THE SMARTCAST™ APP After you Creating/Logging into your MyVIZIO account, the home page of the SmartCast™ app is displayed. Search Menu Device Power Device Settings Device Input Aspect Ratio Picture Settings Volume Controls Device Menu The Device Menu is available throughout the SmartCast app, allowing you to easily access the device controls. Tap to minimize Note: The images shown here are for illustrative purposes only and may be subject to change.
3 Swipe to reveal a list of content categorized into TV Shows, Movies, Music, Live TV, Kids, and Live Streams. You can also access these categorizes by tapping the button in the top left corner. OR Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 USER PROFILE SETTINGS Every user can register their very own user profile (MyVIZIO, Facebook, or Google), keeping their personalized watchlists and collections. To access the Profile page: 1. Tap the button to reveal the side menu. 2. Tap View Profile. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 To modify the account settings: 1. Tap the button to access the account settings page. You can change the First Name, Last Name, E-mail Address, and password by tapping on each of them. To edit profile settings: 1. From the Profile page, tap Edit Profile. You can edit the Profile Color, Profile Name, and Location by taping on each of them. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 PICKING SOMETHING TO WATCH After you get the hang of using the SmartCast app, it’s time for you pick and choose something to watch. 1. Tap on TV Shows, Movies, Live TV, Kids, or Live Steam from the Home page. 2. Depending on which category you pick, the content will be organized into several collections (scroll up and down to reveal additional collection). You can pick your content from the list or search for a title by tapping the search icon .
3 3. Tap on the title you want to watch to see information regarding the cast, meta scores, and etc. 4. A) Tap on the play button. B) Select On Demand or On Now (Online feed*) and tap the play button. C) For On Demand: Select a source and tap the play button. D) Your title begins playing on your display. The Device Menu is displayed − allowing you to control your display settings and content. A B C D Note: The images shown here are for illustrative purposes only and may be subject to change.
3 PICKING SOMETHING TO LISTEN TO If you are in the mood to listen to some music, you can also browse directly from the SmartCast app. 1. Tap on Music from the Home page. 2. Music will be organized into several collections (scroll up and down to reveal additional collection). You can pick your content from the list or search for a title by tapping the search icon . Note: The images shown here are for illustrative purposes only and may be subject to change.
3 3. Tap on the content you want to listen to. 4. A) Tap on the play button. B) Select On Demand or On Now (Online feed*) and tap the play button. C) For On Demand: Select a source and tap the play button. Your content begins playing on your SmartCast device. The Device Menu is displayed − allowing you to control your device settings and content. A B C Note: The images shown here are for illustrative purposes only and may be subject to change.
3 WATCHLISTS While you are browsing for content, you can add titles to a watchlist (My Watchlist) where you can easily access them whenever you want. You can also set alerts to notify you when new episodes are available to watch. To add content to a watchlist: 1. From the Home page, tap on TV Shows, Movies, Kids, or Live Streams. 2. Tap on the title you want to add to your watchlist. Note: The images shown here are for illustrative purposes only and may be subject to change.
3 3. Tap on the button and select Add to My Watchlist to add the title to your watchlist. 4. The Add to Watchlist menu appears. Here you can set an alert for the title, alerting when it will be aired. Tap on Set Alert to turn the notification on. Alert Types: New Airings Only, Live Airings Only, Unwatched Airings Only, or All Airings. Alert Time: 10 minutes, 15 minutes, 30 minutes, or 1 hour before the title airs.
3 To view, edit, and watch titles from your watchlist: button and select My Watchlist. 1. Tap on the 2. The My Watchlist menu is displayed. Tap on a title, select and source, and the content begins to play. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 To edit alerts and remove a title from your watchlist: 1. From the My Watchlist menu, tap on the alerts or remove it from the watchlist. button on each title to edit Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 COLLECTIONS Add movies, and TV shows to your Collections, to build personally categorized lists of content. To add content to a Collections list: 1. Choose a title you want to add to a collection and tap on the and select Add to Collection. 2. The Add to Collection menu appears. Here you can choose which collection you want to add the title to. Tap Create new Collection to create a new Collection list. Create a name and add a description and tap DONE.
3 To view, edit, and watch titles from your Collections: button and select Collections. 1. Tap on the 2. The Collections menu is displayed. Tap on a title, select and source, and the content begins to play. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 To remove titles from your Collection list(s): 1. From the Collections menu, tap on the Collection that contains the title you want to remove. 2. Tap to remove the title from the collection. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 WATCHING LIVE TV* If you have a cable, satellite, or over-the-air TV connection, you can use the VIZIO SmartCast App to search, discover, and browse live TV channels. To set up a TV connection to the SmartCast App: button and select Live TV. 1. From the Home page, tap on the 2. The VIZIO SmartCast App automatically scans for any devices on the same network. Select your device from the list.
3 3. If you chose Add a Channel Lineup for an Unsupported Device, follow the on-screen instructions to complete the setup. A B C D Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 After you setup a TV connection, you can browse through the broadcast schedule, add programs to your Favorites and Watchlists. To browse through the Live TV broadcast schedule: 1. From the Home page, tap on Live TV or select Live TV from the menu. OR 2. Tap on the schedule button to display the full broadcast schedule. Swipe left and right to see the complete broadcast schedule for the day on each channel. Tap the play button to begin watching.
3 To add content programs to your Favorites or Watchlists: • From the schedule page, tap on the button. Tap Add To/Remove From Favorites to add/remove the program from your favorites list. Tap Add To My Watchlists to add the program to your watchlist. To remove the program from your watchlist, see Watchlists on page 26. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 MANAGING CATEGORIES You can add, remove, and rearrange the content categories on the Home page to your preference. All but the Movies and TV Shows categories can be removed. To add or remove a category: button and select Manage 1. From the Home page, tap on the Categories. 2. Tap on the button and remove a category. Tap on the add a category. Note: The images shown here are for illustrative purposes only and may be subject to change.
Device Settings 3 SETTING UP ADDITIONAL SMARTCAST DEVICES To add additional SmartCast devices: button and select Device Settings. 1. From the Home page, tap on the 2. The VIZIO Devices menu is displayed. Tap ADD NEW DEVICE and follow the on-screen instructions to pair your SmartCast device.
3 To remove a SmartCast device: • From the VIZIO Devices menu, tap on the button and tap Remove to remove the SmartCast device from the SmartCast App. To modify SmartCast device settings: • From the VIZIO Devices menu, tap on the SmartCast device listed. See VIZIO SmartCast Display Settings on page for detailed descriptions of each setting. Note: The images shown here are for illustrative purposes only and may be subject to change.
3 To change your SmartCast device name: • From the Display Settings menu, tap on Device Name and enter a new name. Tap Save when you are done. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 ADJUSTING PICTURE SETTINGS In addition to letting you browse, watch, and listen to content, the VIZIO SmartCast App lets you adjust your SmartCast Display settings directly from the App. To access the Picture settings menu: • From the Display Settings menu, tap on Picture. The Picture menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on Picture to access the Picture menu.
3 Your VIZIO Display can be adjusted to suit your preferences and viewing conditions. Tap on each setting to see the available settings. Adjust settings with sliders by sliding your finger left to decrease and right to increase. Changes made while on any preset picture mode will add an asterisk on the top right corner of the preset mode. To adjust the picture settings: • Picture Mode • Standard mode sets the picture settings to the default settings.
3 • Backlight • Adjusts the LED brightness level to affect the overall brilliance of the picture. Backlight cannot be adjusted on some picture modes. • Brightness • Adjusts the black level of the picture. When this setting is too low, the picture may be too dark to distinguish details. When this setting is too high, the picture may appear faded or washed out. • Contrast • Adjusts the white level of the picture. When this setting is too low, the picture may appear dark.
3 • Active LED Zones • Dynamically improves the contrast ratio of the picture by adjusting the backlight. The adjustment is controlled by the content on the screen. Swipe left to Disable and right to Enable. • Reduce Judder • Activates Smooth-Motion motion estimation/motion compensation, which suppresses motion judder, or “studdering” of the image when the camera moves across a scene horizontally. As the setting increases, judder is reduced.
3 Adjusting the Picture Mode Edit Settings Picture Mode Settings allow you to make precise adjustments to the picture and to create picture modes to save groups of picture settings. • Save Picture Mode • Save a custom picture mode. • Lock Picture Mode • Prevent changes to custom picture modes. • Delete Picture Mode • Delete a custom picture mode. Inputs assigned to that custom picture mode will be set to Calibrated picture mode.
3 Locking/Unlocking a Custom Picture Mode Custom picture modes can be locked/unlocked with a unique PIN to prevent accidental changes to their settings. To lock all custom picture modes: 1. From the Picture Mode Edit menu, swipe the Lock Picture Mode switch to the right to lock a picture mode. (Swipe left to unlock) 2. Use the on-screen number pad to enter a unique 4-digit PIN. 3. Tap Save when you are done. Note: Turn the display off and on for feature to go into effect.
3 Deleting a Custom Picture Mode Custom picture modes that are no longer needed can be deleted. Inputs assigned to a deleted custom picture mode become assigned to the Calibrated picture mode. To delete custom picture modes: 1. From the Picture Mode Edit menu, Tap Delete Picture Mode. A dialogue window is displayed. 2. Tap on Yes to delete the custom picture mode. Resetting a Picture Mode Reset the picture mode settings (for a preset picture mode) to the factory default values.
3 Adjusting the Color Calibration Settings Use the color calibration settings to calibrate the image using HSB, offset, gain, and 11 point white balance. You can also reset the color tuner values and perform calibration tests. Current Picture Mode Current Color Temperature To access the color calibration settings menu: 1. From the Picture menu, tap Color Calibration. The Color Calibration menu is displayed.
3 Enabling/Disabling Calibration Tests To enable/disable calibration tests: 1. From the Color Calibration menu, tap Calibration Tests. The Calibration Tests menu is displayed. 2. Select the test pattern you wish to enable. Adjust settings with switches by swiping left to disable and right to enable. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 ADJUSTING AUDIO SETTINGS To access the Audio settings menu: • From the Display Settings menu, tap on Audio. The Audio menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on Audio to access the Audio menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 To adjust the audio settings: • Speakers (Display Speakers) Turns the built-in speakers on or off. Select Auto to have the display automatically detect if there are any devices (such as a sound bar) connected to the Audio Out output ports. • Surround Sound - Surround sound uses DTS TruSurround ™ to deliver an immersive surround sound experience from the display’s internal speakers.
3 ADJUSTING TIMER SETTINGS To access the Timers settings menu: • From the Display Settings menu, tap on Timers. The Timers menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on Timers to access the Timers menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 Activating the Sleep Timer When activated, the display’s sleep timer will turn the display off after a set period of time. To activate the sleep timer: 1. From the Timers menu, tap Sleep Timer. 2. Select the period of time after which you want the display to go to sleep: 30, 60, 90, 120, or 180 minutes. If you do not want the sleep timer to activate, select Off.
3 ADJUSTING NETWORK SETTINGS To access the Network settings menu: • From the Display Settings menu, tap on Network. The Network menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on Network to access the Network menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 Using the Network Connection menu Your display is Internet-ready, featuring both an Ethernet port and built-in highspeed Wireless-AC. Connecting to a Wireless Network To connect to a wireless network whose network name (SSID) is being broadcast: If your display is connected to a network with an Ethernet cable, you will not see the wireless network connection menu. You must disconnect the Ethernet cable to set up a wireless network connection. 1. From the Network menu, tap Wireless Access Points.
3 Finding the MAC Addresses for Network Setup The security settings on your router may require you to enter the display’s MAC address in the router’s settings. To find the display’s MAC address: 1. From the Network menu, tap Manual Setup. The Manual Setup menu is displayed. 2. Find the MAC address for the display at the bottom of the list.
3 Testing your Network Connection To test your network connection: 1. From the Network menu, tap Test Connection. The Test Connection menu is displayed. 2. When the test is complete, your connection results are displayed. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 RENAMING DEVICES ON THE INPUT MENU To access the Inputs menu: • From the Display Settings menu, tap on Inputs. The Inputs menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on Inputs to access the Inputs menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 Renaming Devices on the Input Menu You can rename the inputs to make them easier to recognize on the Input menu. For example, if you have a DVD player connected to the Component input, you can rename that input to display “DVD Player”. To change the name of an input: 1. From the Inputs menu, tap Name Input. The Name Input menu is displayed. 2. Tap on the input you want to rename. The rename window appears. 3. Use the on-screen keyboard to enter your custom label. When you are done tap Save.
3 CHANGING THE DISPLAY SYSTEM SETTINGS To access the System Settings menu: • From the Display Settings menu, tap on System. The System menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on System to access the System menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 Using the System menu, you can: • View system information • Change the on-screen menu language • Set country • Set time zone and local settings • Adjust CEC settings • Adjust mode settings • Adjust when the power indicator is illuminated • Reset the display settings & set up administrative controls Viewing System Information To view a summary of the display settings: • From the System menu, tap System Information. The System Information menu is displayed.
3 Changing the On-Screen Menu Language Your display can display the on-screen menu in different languages. To change the on-screen menu language: 1. From the System menu, tap Menu Language. 2. Tap on your preferred language (English, Español, or Français). Set Country Select your country of choice. To change the on-screen menu language: 1. From the System menu, tap Country. 2. Tap on your country (USA, Canada, or Mexico).
3 Setting the Time and Local Settings To ensure the correct time is displayed, set the display’s time zone: 1. From the System menu, tap Time & Local Settings. The Time & Local Settings menu is displayed. • Use Internet Time - Swipe the switch to the right to have the display sync the time online. • Date & Time - Set the date and time. • Time Zone - Set the time zone. • Daylight Savings Time - turn daylight savings time on, off, or auto. • Time Format - Set time format to 12 or 24 hour format.
3 Turning the Power Indicator On or Off The power indicator on the front of your display normally does not glow when the display is on. You can change this setting if you prefer the indicator to be on. To turn the power indicator light on or off: • From the System menu, swipe the Power Indicator switch to the right to turn the power indicator on. Swipe the switch left to turn the power indicator off. Note: The images shown here are for illustrative purposes only and may be subject to change.
3 Adjusting the Reset & Admin Settings You can use the display’s Reset & Admin menu to set a System PIN, restore the display to its factory default settings, enable/disable Smart Interactivity, and enable/disable the Store Demo. To set a system PIN code: 1. From the Reset & Admin menu, tap Set System PIN Code. 2. Use the on-screen number pad to enter a PIN code. Tap SAVE to continue. 3. Confirm your PIN by entering it again. Tap Submit when you are done. A confirmation window appears, tap CLOSE.
3 To turn Smart Interactivity on or off: • From the Reset & Admin menu, tap Smart Interactivity. Tap Off or On. To enable/disable the Store Demo: • From the Reset & Admin menu, tap Store Demo. Tap Disable or Enable. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 MANAGE MOBILE DEVICES To access the Mobile Devices menu: • From the Display Settings menu, tap on Mobile Devices. The Mobile Devices menu is displayed. OR • From the Device Menu, tap on the button. The Display Settings menu is displayed. Then tap on System to access the System menu. Note: The images shown here are for illustrative purposes only and may be subject to change. The actual on-screen image and text may vary, depending on the model.
3 Paired Mobile Devices The Mobile Devices menu provides a list of mobile devices paired to the display. You can use this menu to delete a pair device from display. To delete a paired device: 1. From the Mobile Devices menu, tap the button next to the device you want to delete. 2. A confirmation window appears, tap YES to continue. The device is deleted. Note: The images shown here are for illustrative purposes only and may be subject to change.
Troubleshooting A Do You Have Questions? Find Answers At SUPPORT.VIZIO.COM Find help with: • New Product Setup • Connecting Your Devices • Technical Problems • Product Updates • And More Live Chat Support Available You can also contact our award-winning support team at: Phone: (877) 698-4946 (TOLL-FREE) Hours Of Operation: Monday - Friday: 7 am to 11 pm (CST) Saturday - Sunday: 9 am to 6 pm (CST) Take A Moment To Register Your Product At VIZIO.
Specifications B M50-D1 Screen Size: 50” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 49.50” 44.40 x 27.98 x 8.70” (112.78 x 71.06 x 2.21 cm) 44.40 x 25.61 x 2.68” (112.78 x 65.06 x 6.80 cm) Weight w/ Stands: w/o Stands: 30.86 lb (14.00 kg) 29.32 lb (13.30 kg) LCD Backlight: D-LED Active LED Zones: 32 Refresh Rate: 120Hz w/ Effective Refresh Rate Clear Action: 360 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 20,000,000:1 Pixel Pitch: 0.2854mm x 0.
B M55-D0 Screen Size: 55” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 54.64” 48.98 x 30.59 x 9.13” (124.40 x 77.69 x 23.18 cm) 48.98 x 28.30 x 2.52” (124.40 x 71.87 x 6.40 cm) Weight w/ Stands: w/o Stands: 36.16 lb (16.40 kg) 34.17 lb (15.50 kg) LCD Backlight: D-LED Active LED Zones: 64 Refresh Rate: 120Hz w/ Effective Refresh Rate Clear Action: 360 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 50,000,000:1 Pixel Pitch: 0.315mm x 0.
B M60-D1 Screen Size: 60” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 64.52” 53.12 x 33.11 x 10.01” (134.93 x 84.11 x 25.42 cm) 53.12 x 30.52 x 2.76” (134.93 x 77.52 x 7.00 cm) Weight w/ Stands: w/o Stands: 48.50 lb (22.00 kg) 47.05 lb (21.34 kg) LCD Backlight: D-LED Active LED Zones: 64 Refresh Rate: 240Hz w/ Effective Refresh Rate Clear Action: 720 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 50,000,000:1 Pixel Pitch: 0.34305mm x 0.
B M65-D0 Screen Size: 65” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 64.52” 57.59 x 35.79 x 10.87” (146.29 x 90.90 x 27.62 cm) 57.59 x 33.15 x 2.52” (146.29 x 84.19 x 6.40 cm) Weight w/ Stands: w/o Stands: 57.32 lb (26.00 kg) 55.34 lb (25.10 kg) LCD Backlight: D-LED Active LED Zones: 64 Refresh Rate: 240Hz w/ Effective Refresh Rate Clear Action: 720 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 50,000,000:1 Pixel Pitch: 0.372mm x 0.
B M70-D3 Screen Size: 70” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 69.50” 61.70 x 38.36 x 11.14” (156.73 x 97.43 x 28.30 cm) 61.70 x 35.53 x 2.72” (156.73 x 90.23 x 6.90 cm) Weight w/ Stands: w/o Stands: 60.41 lb (27.40 kg) 58.20 lb (26.40 kg) LCD Backlight: D-LED Active LED Zones: 64 Refresh Rate: 240Hz w/ Effective Refresh Rate Clear Action: 720 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 50,000,000:1 Pixel Pitch: 0.4008mm x 0.
B M80-D3 Screen Size: 80” Class Viewable Area: Dimensions w/ Stand: Dimensions w/o Stand: 80.00” 71.60 x 44.20 x 15.20” (181.94 x 112.20 x 38.50 cm) 71.60 x 41.20 x 3.20” (181.94 x 104.70 x 8.12 cm) Weight w/ Stands: w/o Stands: 92.37 lb (41.90 kg) 89.29 lb (40.50 kg) LCD Backlight: D-LED Active LED Zones: 64 Refresh Rate: 240Hz w/ Effective Refresh Rate Clear Action: 720 Maximum Resolution: 2160p (4K UHD) Dynamic Contrast Ratio: 50,000,000:1 Pixel Pitch: 0.464mm x 0.
Warranty Information B UNITED STATES AND CANADA BY USING YOUR VIZIO PRODUCT YOU AGREE TO BE BOUND BY ALL THE TERMS OF THIS WARRANTY. BEFORE USING YOUR VIZIO PRODUCT, PLEASE READ THIS WARRANTY CAREFULLY. IF YOU DO NOT AGREE TO THE TERMS OF THIS WARRANTY, DO NOT USE THE VIZIO PRODUCT AND, WITHIN THIRTY (30) DAYS OF THE DATE OF PURCHASE, RETURN IT FOR A REFUND TO THE AUTHORIZED RETAILER WHERE YOU PURCHASED IT.
B ANY DISPUTE, WHETHER IN ARBITRATION, IN COURT, OR OTHERWISE, WILL BE CONDUCTED SOLELY ON AN INDIVIDUAL BASIS. VIZIO AND YOU AGREE THAT NO PARTY WILL HAVE THE RIGHT OR AUTHORITY FOR ANY DISPUTE TO BE ARBITRATED AS A CLASS ACTION, A PRIVATE ATTORNEY GENERAL ACTION, OR IN ANY OTHER PROCEEDING IN WHICH EITHER PARTY ACTS OR PROPOSES TO ACT IN A REPRESENTATIVE CAPACITY.
B does not include de-installation or re-installation of the product. In-home service is subject to availability. VIZIO will provide other service options when in-home service is not available. All other VIZIO products must be sent to a VIZIO service center to obtain warranty service. VIZIO is not responsible for transportation costs to the service center, but VIZIO will cover return shipping to the customer.
Legal & Regulatory D Software Licenses All software is provided subject to a software license agreement(s) and you agree that you will be bound by such license agreement(s) in addition to these terms. Your use of this product is subject to VIZIO’s privacy policy, which may be updated from time to time, and is available to view at http://www.vizio.com/privacy.
B FCC Class B Radio Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
© 2016 VIZIO INC. ALL RIGHTS RESERVED.
