QUICK INSTALL SLIM HDTV MOUNT UNIVERSAL FOR 32” - 55” TVS UP TO 100 LBS XMF1000 - QUICK INSTALL GUIDE
IMPORTANT SAFETY INFORMATION Read the Important Safety Information on this page before installing or using this mounting system. Always follow the instructions in this Quick Install Guide. VIZIO is not liable for damage or injury caused by incorrect mounting, assembly, or use. This mount fits most screens from 32” to 55”. This mounting system supports a maximum weight of 100 lbs and a maximum screen size of 55”.
STEP 1 - BEFORE YOU BEGIN Before you begin the installation, ensure you have all of the items listed on this page. Do not begin the installation unless you have all of the following items. TWO-PERSON JOB Mounting a TV requires power tools. If you are unfamiliar with safe power tool use, consult a professional installer. Mounting a TV requires lifting. To make the installation easier and safer, have someone help you. Always lift properly. YOU WILL NEED Power Drill Pencil 1/2” (12.
STEP 2 - REVIEW THE PACKAGE CONTENTS Before you begin, ensure all parts are included and undamaged. To prevent loss, do not unpack the small parts until they are required. If any parts are missing or damaged, contact VIZIO Customer Service (877) 698-4946.
M4 x2 [ M4 x 44 ] x4 [ M4 x 15 ] LAG M6 x2 x4 [ M6 x 44 ] [ M6 x 20 ] M5 x4 [ M6 x 15 ] M8 x4 x2 [ M5 x 44 ] x4 [ M5 x 15 ] x2 [ M8 x 48 ] x4 [ M8 x 20 ] x4 ANCHOR MISC x4 x4 x4 3
STEP 3A - MOUNTING TO A WALL WITH WOOD STUDS The mount can be attached to walls with wood studs. The wall covering (drywall, lath, plaster, etc.) may not be thicker than 1/2”. 1 1 If you are mounting on a concrete wall, go to Step 3B on page 10. 1. Use the electronic stud finder to locate two studs in the wall. The studs should be approximately 16” apart. Use the pencil to mark the areas of the wall where the studs are located.
3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. 3 Place part A against the wall as shown, and use a wrench to insert the lag bolt and washer into the hole you just drilled. Use Bottom Hole 4. Push the bar through the opening in the bracket (part A) as shown. Push the other bracket (part A) onto the bar and hold it flat against the wall. Ensure it is over the stud. 4 Push Bar Through Snap on the leveler (part E) and level the bar. Mark the location of the hole in the bracket as shown.
5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Using the power drill and the 7/32” drill bit, drill into the pencil mark as shown. Ensure you are drilling into the stud. Drill the hole about 2” into the stud. 5 7/32” 6. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. Place the other bracket (part A) against the wall as shown, and use a wrench to insert the lag bolt and washer into the hole you just drilled. Do not insert the lag bolts completely.
7. Push the bar through the openings in each bracket (part A) as shown. 7 Snap on the leveler (part E) and verify that the bar is level. Level Bar Make any small adjustments, then use a wrench to tighten the 2 lag bolts completely. The bar can be inserted from right to left or left to right, depending on the end of the bar to which you would like the handle attached. Tighten Bolts 8. Using the power drill and the 7/32” drill bit, drill into the top 2 holes as shown.
9. Remove 2 lag bolts and 2 washers from the pouch labeled LAG. 9 Use a wrench to insert the lag bolts and washers as shown. Tighten the bolts completely. 10. Attach the handle (part F) to the end of the bar. 10 Secure the handle to the bar by inserting a screw (part H) into the bottom hole on the handle. Tighten the screw completely.
OPTIONAL: The extender can be attached to lengthen the bar. A longer bar may be easier to access when mounting large TVs. To attach the extender, push it onto the end of the bar. Secure the extender to the bar by inserting a screw (part H) into the bottom hole on the extender. Tighten the screw completely. Secure the handle to the extender by inserting a screw (part I) into the bottom hole on the handle. Tighten the screw completely. H I Go to Step 4 on page 15.
STEP 3B - MOUNTING TO A CONCRETE WALL 1. Determine the height at which you want the mount to hang. Mark the position of the left bracket hole with a pencil. Using the power drill and the 1/2” concrete drill bit, drill a hole into the pencil mark. Drill about 2 1/2” deep. 2. Remove 1 anchor from the pouch labeled ANCHOR. Push the anchor into the hole you just drilled. Ensure the anchor is completely inserted and flush with the wall.
3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. 3 Place a bracket (part A) against the wall as shown, and use a wrench to insert the lag bolt and washer into the anchor. Use Bottom Hole 4. Push the bar through the opening in the bracket (part A) as shown. Push the other bracket (part A) onto the bar and hold it flat against the wall. Ensure it is at least 16” from the other bracket. 4 16” 1 2 Snap on the leveler (part E) and level the bar.
5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Allow the attached bracket to swing down. Using the power drill and the 1/2” concrete drill bit, drill into the 3 pencil marks as shown. Drill each hole about 2 1/2” deep. 5 1/2” Penci l Mark s 6 6. Remove 3 anchors from the pouch labeled ANCHOR. Push the anchors into the holes you just drilled. Ensure the anchors are completely inserted and flush with the wall.
7. Remove 3 lag bolts and 3 washers from the pouch labeled LAG. 7 Place the other bracket (part A) against the wall as shown, and use a wrench to insert the lag bolts and washers into the anchors. Do not insert the lag bolts completely. Leave 1/2” of the bolts showing. 8. Push the bar through the openings in each bracket (part A) as shown. Snap on the leveler (part E) and verify that the bar is level. 8 Level Bar Make any small adjustments, then use a wrench to tighten the 4 lag bolts completely.
9. Attach the handle (part F) to the end of the bar. 9 Secure the handle to the bar by inserting a screw (part H) into the bottom hole on the handle. Tighten the screw completely. Insert Screw in Bottom Hole OPTIONAL: The extender can be attached to lengthen the bar. A longer bar may be easier to access when mounting large TVs. To attach the extender, push it onto the end of the bar. Secure the extender to the bar by inserting a screw (part H) into the bottom hole on the extender.
STEP 4 - ATTACHING THE TV HOOKS AND KICK STANDS 1. Gently place the TV on the floor screen-down. You may want to place a rug or blanket beneath the screen to prevent scratches. 1 In your TV’s User Guide, find the size and depth of your TV’s mounting holes. These will be listed as M4, M5, M6, or M8. Mounting Holes Open the pouch labeled with the size that matches your TV’s mounting holes.
OPTIONAL: If you want your TV to have a 9° downward tilt when mounted, use the spacers (part G) and the longer screws when mounting the TV hooks. 3. Using the screwdriver, insert the screws and washers as shown. Because each TV is different, your VIZIO TV mount includes screws of different lengths. Use screws that can be inserted completely. Do not use a short screw if a longer screw can be inserted completely.
4. Place the two kickstands (parts C and D) against the two bottom mounting holes as shown. 4 The larger kickstand can be placed on either the left or right mounting hole. Arrow Points Up 5. Using the screwdriver, insert the screws and washers as shown. 5 Do not use a short screw if a longer screw can be inserted completely. Go to Step 5 on page 18.
STEP 5 - HANGING THE TV ON THE MOUNT 1 This step requires lifting the TV. To prevent injury to yourself or damage to your TV, perform this step with the help of another person. Bar 1. Turn the handle on the bar until the flat side of the bar is facing the wall. Flat Side of Bar Facing Wall 2. With the help of another person, lift the TV and hang the TV hooks on the bar as shown.
3. Turn the handle on the bar until the flat side of the bar is facing down. 3 Ensure the flat side of the bar is facing down. This locks the TV to the bar. If the flat side of the bar is not facing down, your TV is not locked to the bar. Hide Handle Behind TV Adjust the position of the TV by sliding it to the left or right. Hide the handle behind the TV by swinging it downward as shown. Flat Side of Bar Facing Down 4.
OPTIONAL: Your mount includes an anti-theft device. Attaching this device prevents the TV from being removed from the mount. To attach the device, remove the security screw and the locking tool from the pouch (part J). Insert the security screw as shown and use the locking tool to tighten. Be sure to save the locking tool. You will need it to remove the security screw in the future. The mount setup is complete. To remove the TV from the mount, perform Step 5 in reverse.
ONE-YEAR LIMITED WARRANTY & INSURANCE Covers units purchased as new in United States and Puerto Rico Only VIZIO warrants for a period of one (1) year from the date of purchase to the original purchaser of its mounting brackets, that the bracket shall be free from defects in assembly, material, or workmanship and will repair or replace, at its sole discretion, a defective bracket free of charge, provided the bracket is returned to VIZIO with shipping prepaid by purchaser.
TRADEMARKS SHOWN ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. IMAGES USED ARE FOR ILLUSTRATION PURPOSES ONLY. VIZIO, THE V LOGO, WHERE VISION MEETS VALUE, AND OTHER VIZIO TRADEMARKS ARE THE INTELLECTUAL PROPERTY OF VIZIO INC. PRODUCT FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. © 2010 VIZIO INC. ALL RIGHTS RESERVED.