6.0.1
Table Of Contents
- vSphere Storage
- Contents
- About vSphere Storage
- Updated Information
- Introduction to Storage
- Overview of Using ESXi with a SAN
- Using ESXi with Fibre Channel SAN
- Configuring Fibre Channel Storage
- Configuring Fibre Channel over Ethernet
- Booting ESXi from Fibre Channel SAN
- Booting ESXi with Software FCoE
- Best Practices for Fibre Channel Storage
- Using ESXi with iSCSI SAN
- Configuring iSCSI Adapters and Storage
- ESXi iSCSI SAN Requirements
- ESXi iSCSI SAN Restrictions
- Setting LUN Allocations for iSCSI
- Network Configuration and Authentication
- Set Up Independent Hardware iSCSI Adapters
- About Dependent Hardware iSCSI Adapters
- Dependent Hardware iSCSI Considerations
- Configure Dependent Hardware iSCSI Adapters
- About the Software iSCSI Adapter
- Modify General Properties for iSCSI Adapters
- Setting Up iSCSI Network
- Using Jumbo Frames with iSCSI
- Configuring Discovery Addresses for iSCSI Adapters
- Configuring CHAP Parameters for iSCSI Adapters
- Configuring Advanced Parameters for iSCSI
- iSCSI Session Management
- Booting from iSCSI SAN
- Best Practices for iSCSI Storage
- Managing Storage Devices
- Storage Device Characteristics
- Understanding Storage Device Naming
- Storage Refresh and Rescan Operations
- Identifying Device Connectivity Problems
- Edit Configuration File Parameters
- Enable or Disable the Locator LED on Storage Devices
- Working with Flash Devices
- About VMware vSphere Flash Read Cache
- Working with Datastores
- Understanding VMFS Datastores
- Understanding Network File System Datastores
- Creating Datastores
- Managing Duplicate VMFS Datastores
- Upgrading VMFS Datastores
- Increasing VMFS Datastore Capacity
- Administrative Operations for Datastores
- Set Up Dynamic Disk Mirroring
- Collecting Diagnostic Information for ESXi Hosts on a Storage Device
- Checking Metadata Consistency with VOMA
- Configuring VMFS Pointer Block Cache
- Understanding Multipathing and Failover
- Raw Device Mapping
- Working with Virtual Volumes
- Virtual Machine Storage Policies
- Upgrading Legacy Storage Profiles
- Understanding Virtual Machine Storage Policies
- Working with Virtual Machine Storage Policies
- Creating and Managing VM Storage Policies
- Storage Policies and Virtual Machines
- Default Storage Policies
- Assign Storage Policies to Virtual Machines
- Change Storage Policy Assignment for Virtual Machine Files and Disks
- Monitor Storage Compliance for Virtual Machines
- Check Compliance for a VM Storage Policy
- Find Compatible Storage Resource for Noncompliant Virtual Machine
- Reapply Virtual Machine Storage Policy
- Filtering Virtual Machine I/O
- VMkernel and Storage
- Storage Hardware Acceleration
- Hardware Acceleration Benefits
- Hardware Acceleration Requirements
- Hardware Acceleration Support Status
- Hardware Acceleration for Block Storage Devices
- Hardware Acceleration on NAS Devices
- Hardware Acceleration Considerations
- Storage Thick and Thin Provisioning
- Using Storage Providers
- Using vmkfstools
- vmkfstools Command Syntax
- vmkfstools Options
- -v Suboption
- File System Options
- Virtual Disk Options
- Supported Disk Formats
- Creating a Virtual Disk
- Example for Creating a Virtual Disk
- Initializing a Virtual Disk
- Inflating a Thin Virtual Disk
- Removing Zeroed Blocks
- Converting a Zeroedthick Virtual Disk to an Eagerzeroedthick Disk
- Deleting a Virtual Disk
- Renaming a Virtual Disk
- Cloning or Converting a Virtual Disk or RDM
- Example for Cloning or Converting a Virtual Disk
- Migrate Virtual Machines Between DifferentVMware Products
- Extending a Virtual Disk
- Upgrading Virtual Disks
- Creating a Virtual Compatibility Mode Raw Device Mapping
- Example for Creating a Virtual Compatibility Mode RDM
- Creating a Physical Compatibility Mode Raw Device Mapping
- Listing Attributes of an RDM
- Displaying Virtual Disk Geometry
- Checking and Repairing Virtual Disks
- Checking Disk Chain for Consistency
- Storage Device Options
- Index
3 From the list of available targets, select a target to congure and click Authentication.
4 Deselect Inherit from parent and specify authentication method.
n
None
n
Use unidirectional CHAP if required by target
n
Use unidirectional CHAP unless prohibited by target
n
Use unidirectional CHAP
n
Use bidirectional CHAP. To congure bidirectional CHAP, you must select this option.
5 Specify the outgoing CHAP name.
Make sure that the name you specify matches the name congured on the storage side.
n
To set the CHAP name to the iSCSI adapter name, select Use initiator name.
n
To set the CHAP name to anything other than the iSCSI initiator name, deselect Use initiator name
and type a name in the Name text box.
6 Enter an outgoing CHAP secret to be used as part of authentication. Use the same secret that you enter
on the storage side.
7 If conguring bi-directional CHAP, specify incoming CHAP credentials.
Make sure to use dierent secrets for the outgoing and incoming CHAP.
8 Click OK.
9 Rescan the iSCSI adapter.
If you change the CHAP parameters, they are used for new iSCSI sessions. For existing sessions, new
seings are not used until you log out and login again.
Disable CHAP
You can disable CHAP if your storage system does not require it.
If you disable CHAP on a system that requires CHAP authentication, existing iSCSI sessions remain active
until you reboot your host, end the session through the command line, or the storage system forces a logout.
After the session ends, you can no longer connect to targets that require CHAP.
Required privilege: Host..Storage Partition
Procedure
1 Open the CHAP Credentials dialog box.
2 For software and dependent hardware iSCSI adapters, to disable just the mutual CHAP and leave the
one-way CHAP, select Do not use CHAP in the Mutual CHAP area.
3 To disable one-way CHAP, select Do not use CHAP in the CHAP area.
The mutual CHAP, if set up, automatically turns to Do not use CHAP when you disable the one-way
CHAP.
4 Click OK.
Chapter 10 Configuring iSCSI Adapters and Storage
VMware, Inc. 101