User's Manual
Table Of Contents
- Vocera Badge User Guide
- Contents
- Welcome to Vocera
- Badge Features
- Commands
- Basic Calling
- Advanced Commands
- Blocking and Accepting Calls
- Broadcasting to a Group
- Calling Telephone Numbers
- Calling an Address Book Entry or Buddy
- Forwarding Your Calls
- Getting Other Information
- Issuing Urgent Commands
- Joining or Leaving a Group
- Locating a Vocera User or Group Member
- Navigating IVR Phone Trees with a Badge
- Placing a Three-Way Conference Call
- Redialing Phone Numbers
- Sending and Receiving Numeric Pages
- Using Instant Conferences
- Optional Commands
- Special Features
- Communicating with Multiple Sites
- Commands for Group Managers
- Sending Text Messages to Vocera Devices
- Using Vocera Access Anywhere
- The User Console
- Maintaining Your Badge
- Notification Prompts
- Reference
- Frequently Asked Questions
- Why does the Genie have trouble understanding me?
- Why is my device chirping or beeping?
- Why does my device beep when I'm talking to someone?
- Why does my device display say "Searching for Server"?
- Why does the Genie ask me to wait when I press Call?
- Why can't I receive calls or messages?
- Why do some text messages begin with strange characters?
- Why does my badge beep and then restart?
- What can I do if badge buttons are not working?
- How can I stop getting logged out when I charge my badge?
- Agreements, Specifications, and Notices
- Important Safety Instructions
- Command Reference
- Block and Accept Calls
- Broadcast to a Group
- Call a User or Group Member
- Dial a Telephone Number
- Environmental Services
- Forward a Call
- Getting Help
- Locate Users and Groups
- Log In and Log Out
- Manage Groups
- Miscellaneous
- Place a Three-Way Conference Call
- Play Messages
- Record Your Name and Greeting
- Send and Receive Numeric Pages
- Send Messages
- Summon and Dismiss the Genie
- Transfer a Call
- Use Instant Conferences
- Work With Your Groups
- Work with Sites
- Frequently Asked Questions
AGREEMENTS, SPECIFICATIONS, AND NOTICES
112 VOCERA BADGE USERGUIDE
Complies with IDA Standards DA101094
Notice to Brazil Users
B2000 Regulatory Notices
FCC Compliance for United States Users
FCC Part 15.247
FCC Part 15, Class B Device
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause unwanted operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against interference in a commercial or residential installation. There is no guarantee,
however, that interference will not occur in any particular installation. If this equipment does cause
interference with radio or television reception, the user should try to correct the interference by
employing one or more of the following:
• Reorient or relocate the receiving antenna on the affected equipment.
• Increase the separation between the affected equipment and the badge.
• Consult the dealer or an experienced technician for help.
Any changes or modifications to this device not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Specific Absorption Rate (SAR) Exposure Guidelines
THIS BADGE MEETS THE FCC REQUIREMENTS FOR EXPOSURE TO RADIO FREQUENCY
ENERGY (SAR).
Your wireless badge is a radio transmitter and receiver. It is designed and manufactured
not to exceed the emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. These limits are part of a
set of comprehensive guidelines that establish permitted levels of RF energy for the general
population. The guidelines are based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all persons, regardless of
age and health. The exposure standard for wireless communications devices employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is
1.6W/kg. Tests for SAR are conducted using standard operating positions, as applicable to this
device, specified by the FCC. The standard incorporates a substantial margin of safety to give
additional protection for the public and to account for any variations in measurement. Before a
badge is available for sale to the public, sample units must be tested by a certified regulatory lab
to verify that they do not exceed the limit established by the government-adopted requirement for
safe exposure.