Quick Start Guide

Description
FAQ
Q1. Why did I fail to add my T Guard to the VOCOlinc app?
1. If the screen shows “Couldn’t find the accessory” after scanning the setup code:
(1) Make sure your accessory is powered on and nearby.
(2) Make sure to turn on Bluetooth for your iOS device.
2. Make sure the setup code is entered correctly. Select the accessory shown on screen in .
manual mode, then input the setup code (XXX-XX-XXX) which can be found on the interior
cover or quick start guide.
3. If the app prompts “Couldn’t add VOCOlinc-XXX-XXXXXX” after scanning the setup code:
(1) Close the app
(2) Reboot the phone
(3) Factory reset the product
(4) Add the accessory again
4. If the screen shows “The setup code is incorrect”, please
(1) Double check whether the setup code input is right or not; or try manually entering
the setup code. The setup code can be found on the interior cover or quick start guide .
(2) If the last 6 characters of the identification code is not consistent with the last 6 characters
of MAC on the top of the battery holder, please report this issue by sending a message
to [e-mail] along with the last 6 characters of the identification code.
Q2. May I control the lock remotely?
Yes. You need to use Apple TV [Gen. 4], iPad, or HomePod as a hub.
NOTE: Please turn off the “standby mode” when Apple TV is used as a hub.
Q3. What should I do if the lock is not responding?
1. Keep iOS device close to your product and ensure your iphone/ipad within
connectivity range (best within 20 feet).
2. If touch keypad become inactive:
(1) Check if batteries are installed correctly according to the direction marks on the
battery holder.
成型尺寸: 65x100mm
128g双铜纸，印4C，表面过光油，折页
Setup code
VOCOlinc APP
Features:
• Touchscreen
• Works with Apple HomeKit
• Siri Control
• Remote Access (Apple TV [Gen. 4],
iPad, or HomePod required)
• Multi-user management
• Key authorization
• Activity tracking
• Auto-lock
What's in the box?
• Complete Lockset and Hardware
• Entry Keys (2)
• Installation Guide
• Quick Start Guide
Electrical Ratings
• 4 x AA high-capacity Alkaline batteries (purchased seperately)
Using the Touchscreen Keypad
Wake up Touchscreen Keypad
Press & hold the “ ” key until you hear the beeping sound or see the backlight
turned on.
Secure Locking
After 4 incorrect code attempts, the backlight will be turned off and the keypad will
temporarily shut down for 60 seconds.
Fast Locking
Wake up Keypad and Tap “ ” key
T Guard Smart Lock is a deadbolt with touchscreen keypad that works on AA Alkaline
Batteries. Say goodbye to pulling out your keys and putting them back. It is Apple
HomeKit-Enabled meaning you can lock/unlock your door using Siri or your iPhone,
even when you are away home (Apple TV [Gen. 4], iPad, or HomePod required).
The VOCOlinc app allows you to create up to 30 passcodes and share with your family,
friends or a dog watcher for ultimate convenience. You can get notifications upon
door activities, and check activities on a specific day/period. Secure your home today
with T Guard.
1
2
3
Slide open
Unlocked-Green; Locked/Jammed-Red
Lock/Clear wrong entry
Battery Cover
VOCOlinc LED
Lock key
4
5
6
Passcodes entry; lock/unlock; factory reset
Unlock/Wakeup keypad
Lock/unlock
Touchpad
Unlock key
Turning Piece
Buzzer & LED Indicator Status
Action
Backlight Status Buzzer
Power on All lights on Beeps once
Red&green lights on
interchangeably twice
then off
Green light blinks once
Red light blinks once
All lights on
Key light blinks once
Red light blinks twice
All lights off and keypad
shuts down for 60s
All lights off
n/aFactory reset
Continuous beeping
until it is completed
ldentify
Unlock
Lock
Wakeup keypad
Tap key
Jammed
Error password
4 times
(keypad locked)
Keypad stand-by
Beeps twice
Beeps once
Beeps once
Beeps once
Beeps once
n/a
n/a
n/a
5. Select the device from the accessory list. Each accessory has a unique identification code,
e.g., VOCOlinc-XXX-XXXXXX. Make sure the last 6 characters of the identification code is
consistent with the last 6 characters of MAC on the top of the battery holder.
6. If the screen shows “Couldn’t add VOCOlinc-XXX-XXXXXX”, please factory reset the
product and then retap “+ ” icon on the mainpage. DO NOT lose the setup code.
7. You can name your device and refer to it when speaking to Siri. For example, if you name
your device “Front Door”, you may wake up Siri and say “Lock/unlock my front door”.
8. The use of a HomeKit-enabled accessory need the follow permissions:
Settings > iCloud > iCloud Drive > Turn On
Settings > iCloud > Keychain > Turn On
Settings > Privacy > HomeKit > VOCOlinc > Turn On
4. You will be asked to scan the setup code or manually enter the setup code. The setup
code is a QR code located on the interior cover.
Setup Guide
1. Factory Resetting
Within 15 seconds immediately after inserting the batteries, enter 1234+" " . Once
completed, the lock reboots. You should hear a long beeping sound coming from
the buzzer.
NOTE: DO NOT power off until operation is restored after factory reset.
2. Turn on Bluetooth of your iOS device
3. Download and open the VOCOlinc app, Tap “+ ” icon on the mainpage and
follow the on-screen directions to complete setup.
(2) Check if the battery level is low. If so, change with new batteries and try turning on/off
your product.
(3) Check if the the cable from the exterior assembly connects correctly with interior cover.
During trouble shooting, use entry keys as a temporary alternative.
Q4. The lock fails to lock/unlock when the connection is on.
1. If low power warning shows on the screen, please immediately change batteries.
2. DO NOT mix old batteries with the new ones nor different brands.
Q5. I am not able to add/change the passcode? What went wrong?
1. If the screen shows “This accessory is unreachable”, please ensure your iOS device is
within connectivity range from your product (best within 20 feet).
2. If you are a invitee, please ask the Administrator to turn off “Administrator Only
Access” mode.
Q6. Why does the touch keypad become inactive?
Q7. Why is my T Guard keeps showing“jammed”on the app?
1. Please check the door is completely closed.
2. Please check the door gaps for any foreign objects between door and frame.
3. Please check the lock is installed properly according to the Installation Guide.
NOTE:
Once the above is done, the “jammed” sign will be removed after 1 cycle of lock and
unclock by App.
If you have more questions, please feel free to contact us: [e-mail]
1. Wait for 1 minite and then press and hold “ ” key to activate keypad. Your product
might be secure-locked after 4 incorrect passcode inputs.
2. If the backlight is stays on, please check if the the cable from the exterior assembly
connects correctly with interior cover.
System Requirement:
- Mobile device running iOS10.3 or later
- Support Bluetooth v4.2
FCC Declaration
Caution:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation. Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment.
The device has been evaluated to meet general RF exposure requirement. The device can
be used in portable exposure condition without restriction.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement
Radio apparatus containing digital circuitry which can function separately from the
operation of a transmitter or an associated transmitter, shall comply with ICES-003.
In such cases, the labelling requirements of the applicable RSS apply, rather than the
labelling requirements in ICES-003. This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Smart Lock
Deadbolt with Touch Screen Keypad
T Guard
Authorization
User passcode
Create up to 30 passcodes and share with your family, friends or a dog watcher for ultimate
convenience. You can set Always, Recurring, Temporary, Once. Enter the authorization page
to view the passcode summary.
Organize your users into groups so that you find them easily.
Groups
Settings
Beeping
Turn on/off the beeping sound.
Touch Sensitivity
You can choose from 3 sensitivity levels.
Administartor Only Access
Turning on this mode means all user authorizations will become ineffective except for the
administrator (initially paired) account.
Warning:
if a invitee has been enabled
“Allow Remote Access”,
the invitee is deemed the
administrator when she
locks/unlocks the door or
add/edit passcode remotely.
Power-saving (Away)
Turning on the power-saving
mode will disable
touchscreen keypad to
further save power.
Activity
The lock records all activities and sync with your iOS device. You can track them easily
by setting a period.
Note:
• Only the devices that are
currently reachable and have
an available update will prompt
firmware update notice.
• It is important to leave the
VOCOlinc app running while it
finishes updating the device.
Try not to minimize the app,
close the app,or interrupt the
update to prevent problems.
When the battery level is lower
than 20%, the Low Battery
warning shows up on the screen.
Please change your batteries
immediately.
To gain better experience with VOCOlinc product, we strongly recommend that you update
firmware whenever updates with all the latest improvement and fixes are available:
1. Open the VOCOlinc app.
2. Make sure your iPhone/iPad has been conneted to wireless network and your product.
3. You will be promt a message of the update whenever the update is available.
4. Tap the ”update” to begin.
Firmware Update
Low Battery Warning
The VOCOlinc App
Home Screen
You can obtain a straight forward view of the status: Locked/Locking, Unlocked/Unlocking
or Jammed.
Industry Canada Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux
deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris
IC:26783-TGUARD