Owner's manual

ManualsBrandsVocoPro Manualsaudio & home theatreTWISTER-II

(REAR PANEL CONT.)

PARTS AND FUNCTIONS

LEFT AND RIGHT CHANNEL RECORD (“REC”) OUTPUT

JACKS: These two outputs jacks can be used to connect an

additional tape deck. Connect the left (“L”) and right (“R”)

record (REC) output jacks to the respective left (“L”) and right

(“R”) record (REC) input jacks on the back of your external

tape deck. Only the music being played on the Twister II will

record onto your external tape deck. (Follow instructions

for using either player on the Twister II) Play the desired CD/

CDG or cassette on the Twister II and record it on your

external tape deck. Vocals from the Twister II will not be

recorded using these jacks. To record music and vocals

from the Twister II to an external tape deck connect your

external tape deck to the “L” AND “R” “PRE” output jacks

of the “AUDIO OUTPUT” section. (See #16 on REAR PANEL

diagram. Also see “CONNECTING OTHER COMPONENTS

TO THE TWISTER II”, “Expanding Your System”)

AC POWER CORD: Plugs into any AC wall outlet.

LEFT AND RIGHT CHANNEL “PRE” OUTPUT JACKS: These

two output jacks can be used to connect an external tape

deck on which to record music AND vocals, being played

on the Twister II. Connect the left “L” and right “R” “PRE”

output jacks of the Twister II to the respective left “L” and right

“R” input jacks (usually “REC IN” on most tape decks)

on the back of your external tape deck. (Follow

instructions for using either player on the Twister II) Play

the desired CD/CDG or cassette on the Twister II and record

it on your external tape deck.

VIDEO OUTPUT JACK: The video output jack is used to

connect the Twister II to a television monitor. When properly

connected, the television monitor will display lyrics and

graphics from CDG discs being played on the Twister II.

There are three ways to connect a television monitor to the

Twister II. 1) Connect the “VIDEO OUTPUT” jack to the “VIDEO

IN” on the back of the television monitor. There is an RCA

connector cord provided with the Twister II for this type

of connection. BE SURE TO SWITCH YOUR TELEVISION

MONITOR TO “VIDEO” MODE, OTHERWISE LYRICS AND

GRAPHICHS WILL NOT APPEAR. 2) If your television moni-

tor does not have and RCA type connector and only has a

coaxial connector, you can use a VCR to connect the

Twister II to your television monitor. To do this, connect the

“VIDEO OUTPUT” jack on the back of the Twister II to the

“VIDEO IN” on the VCR. (See diagram on opposite page).

BE SURE THE TELEVISION MONITOR IS SET TO “ VIDEO”

MODE AND THE VCR SETTING CORRESPONDS TO THE

JACKS YOU HAVE CONNECTED THE TWISTER TO, OTHER-

WISE LYRICS AND GRAPHICHS WILL NOT APPEAR. If you

are unsure of which setting on the VCR should be used, see

manufacutrer’s instructions provided with the VCR. 3) If you

do not have a VCR, or RCA connectors on the back of

your television monitor. You will need an “RF” modulator.

To use an “RF” modulator, connect the “VIDEO OUTPUT”

jack on the back of the Twister II to the “VIDEO IN” jack on the

“RF” modulator. Next, Connect the “OUTPUT” of the “RF”

modulator, with a coaxial cable (not provided) , to the

“ANTENNA INPUT” of the television monitor. BE SURE

TO SET THE TELEVISION MONITOR TO “CHANNEL 3”,

OTHERWISE LYRICS AND GRAPHICS WILL NOT APPEAR.

(Refer to diagram on opposite page)

VIDEO INPUT JACKS: There are two video input jacks on the

back of the Twister II. They both serve the same purpose

and can be used to connect two external players at a time.

They are labeled seperately, “DVD” (digital video disc) and

“LD” (laser disc), to allow you to easily identify which jack you

have connected to which player. When a DVD or LD player

has been properly connected, (See “CONNECTING OTHER

COMPONENTS TO THE TWISTER”), the television monitor

connected to the Twister II will display lyrics and graphics

from the discs being played on the external player(s).

To connect an external player use an RCA connector cable.

Connect either the DVD or LD VIDEO INPUT jack on the back

of the Twister II to the “VIDEO OUTPUT” jack on the external

respective player. The basic rule is “INPUT” connected to

OUTPUT”. WHEN PLAYING AND EXTERNAL DVD OR LD

PLAYER, BE SURE TO SELECT THE DVD OR LD SETTING ON

THE FRONT OF THE TWISTER II, OTHERWISE THERE WILL

BE NO AUDIO OR VIDEO. (See FRONT PANEL diagram, #26,

#27)

RIGHT AND LEFT AUDIO INPUTJACKS TO CONNECT

EXTERNAL LASER DISC (LD) PLAYER: The “R” and “L”

“AUDIO INPUT” jacks are used to connect an external laser

disc player to the Twister II. When properly connected,

the Twister II will play the music being played on the

laser disc player through the Twister II speakers.

Connect the “R” and “L” “AUDIO INPUT” jacks on the Twister

II to the “L” and “R” “AUDIO OUTPUT” jacks on the laser disc

player, using an RCA type connector cable. WHEN

PLAYING AND EXTERNAL LD PLAYER, BE SURE TO SELECT

LD SETTING ON THE FRONT OF THE TWISTER II,

OTHERWISE THERE WILL BE NO AUDIO OR VIDEO.

RIGHT AND LEFT AUDIO INPUTJACKS TO CONNECT

AN EXTERNAL DIGITAL VIDEO DISC (DVD) PLAYER: The “R”

and “L” “AUDIO INPUT” jacks are used to connect an exter-

nal laser disc player to the Twister II. When properly con-

nected, the Twister II will play the music being played on the