user manual

ManualsBrandsVogelzang International ManualsStoveStove TR008

TR008 / 050207.2 DURANGO™ / Page 1

READ ALL INSTRUCTIONS CAREFULLY

BEFORE STARTING THE INSTALLATION

OR OPERATING THE STOVE. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT

IN PROPERTY DAMAGE, BODILY INJURY,

OR EVEN DEATH.

DO NOT USE THIS STOVE IN A

MOBILE HOME, MANUFACTURED HOME,

TRAILER OR TENT — NO EXCEPTIONS!

This stove meets

Test Standards:

UL 1482-1996 U.S.

SAFETY INSTRUCTIONS

SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED A HOUSE/BUILDING FIRE

MAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT

PERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.

READ ALL INSTRUCTIONS CAREFULLY.

1. The installation of this stove must comply

with your local building code rulings. Please

observe the clearances to combustibles (see

Locating Stove). Do not place furniture or

other objects within the clearance area.

2. Verify that the stove is properly installed

before ﬁring the stove for the ﬁrst time.

After reading these instructions, if you have

any doubt about your ability to complete

your installation properly, you must ob-

tain the services of a professional licensed

installer familiar with all aspects of safe

and correct installation. DO NOT use

temporary or makeshift compromises

during installation.

3. DO NOT store wood, ﬂammable liquids or

other combustible materials too close to the

unit. Refer to certiﬁcation label on back of

unit and minimum clearances under Locat-

ing Stove in the following instructions.

4. Do not install this stove in a mobile

home, manufactured home, trailer or tent

(NO EXCEPTIONS! per HUD Federal

Standard: 24 CFR Ch.XX).

5. If any parts are missing or defective, please

notify the dealer or manufacturer immediately.

DO NOT OPERATE A STOVE THAT IS

MISSING ANY PARTS!.

6. Do not tamper with combustion air control

beyond normal adjustment capacities.

7. Always connect this stove to a chimney and

vent to the outside. Never vent to another room

or inside a building. DO NOT CONNECT

THIS UNIT TO A CHIMNEY FLUE SERV-

ING ANOTHER APPLIANCE.

8. DO NOT CONNECT a wood burning stove

to an aluminum Type B gas vent. This is

not safe. Use approved masonry or a UL

103 HT Listed Residential Type and Build-

ing Heating Appliance Chimney. Use a 6”

diameter chimney, that is high enough to

Vogelzang International Corporation

400 West 17th Street

Holland, Michigan 49423

www.vogelzang.com

Phone: 1-616-396-1911

Fax: 1-616-396-1971

THE DURANGO

™

HiGH

EfficiENcy WOODsTOvE

EPA Certiﬁed (3.6 grams/hr)

Model TR008 Owners Manual

(save this manual for future reference)

continued on next page

Summary of content (22 pages)

PAGE 1
THE DURANGO™ High Efficiency Woodstove EPA Certified (3.6 grams/hr) Model TR008 Owners Manual (save this manual for future reference) READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION OR OPERATING THE STOVE. Failure to follow instructions may result in property damage, bodily injury, or even death. Do NOT use this stove in a mobile home, Manufactured Home, trailer or Tent — NO EXCEPTIONS! This stove meets Test Standards: UL 1482-1996 U.S.
PAGE 2
SAFETY INSTRUCTIONS continued… give a good draft. (See specifics in Chimney Connections instructions). 9. Be sure that your chimney is safely constructed and in good repair. Have the chimney inspected by the fire department or a qualified inspector. Your insurance company should be able to recommend a qualified inspector. 10. Creosote or soot may build up in the chimney connector and chimney and cause a house/ building fire.
PAGE 3
Assembly Instructions NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of your wood stove and assumes no responsibility of any incidental or consequential damages. Tools and Materials Required for Installation tools • • • • • • • • • Pencil 6 foot Folding Rule or Tape Measure Tin Snips Drill: Hand or Electric 1/8” dia.
PAGE 4
Assembly Instructions continued… 10. Attach blower assembly to rear of the back heat beyond either side of the stove pipe if it is shield with four Phillips head machine screws elbowed towards a wall. (See figures 3 & 5 and from the hardware pack. Make sure to position consult local building codes and fire protecthe ceramic gasket between the back heat shield tion ordinances). A grouted ceramic floor tile and the blower assembly. installed per local building code is considered a durable equivalent. 11.
PAGE 5
Locating Stove continued… CORNER CLEARANCES 13" 13" Fig. 4 – Top View Minimum Corner Clearances from Combustible Surfaces 6. Do Not install this stove in a m o b i l e h o m e , m a n u fa c tured home, trailer or tent – NO EXCEPTIONS! (HUD Federal Standard: 24 CFR Ch.xx) 7. The clearances provided are minimum dimensions determined by Omni-Test Laboratories, Inc., the manufacturer’s testing laboratory.
PAGE 6
Locating Stove Firebrick Assembly CAUTION: REPLACE FIREBRICKS Before firing woodstove. Position firebricks so no gaps remain between bricks. Firebrick protects the stove body, extends the life of your stove and radiates heat more evenly. Check to see that all firebricks are in their correct positions and have not become misaligned during shipping or assembly. If removed for ease of locating stove, firebrick must be replaced before firing.
PAGE 7
Chimney connections The stove must be connected to either a masonry or manufactured metal chimney built and tested to the specifications listed on the previous pages. Chimneys perform two functions: 1). As a means of exhausting smoke and flue gases which are the result of fuel combustion. 2). The chimney provides “draft” which allows oxygen to be continuously introduced into the appliance, so that proper combustion is possible. This stove relies on natural draft to operate.
PAGE 8
Chimney connections continued … Manufactured Chimney Refer to chimney and chimney connector maker’s instructions for installation and use. Use only 6” diameter listed chimney UL 103 HT type. Chimney made to this listing is High Temperature rated to 2100 degrees Fahrenheit. Use chimney from only one manufacturer. Never mix brands. Carefully follow the chimney manufacturer’s stated requirements and clearances.
PAGE 9
Chimney connections continued … professional. Do Not use a chimney that is unlined 1. An entry hole must be cut through the masonry or damaged!) If you have any question regarding and tile liner with minimal damage to the liner. the condition of the chimney, consult a qualified At least 8” of liner must remain below the entry licensed contractor, qualified engineer, competent position.
PAGE 10
Chimney connections continued … If you have any questions regarding venting your stove, contact the manufacturer or contact the National Fire Protection Association (NFPA) and request a copy of the latest editions of NFPA Standard 211 and NFPA Standard 908. Their address is: Battery March Park, Quincy, MA 02269.
PAGE 11
Operating Instructions given off by the burning wood and increases the efficiency of the stove and reduces chimney emissions. Smoke given off by burning fuel consists of very small organic liquid droplets. If these droplets condense, they form a sticky tar-like substance called creosote. When operated properly, this stove is designed to burn these droplets. Burning these droplets releases heat that would otherwise be lost up the chimney as smoke.
PAGE 12
Operating continued... Service Hints Adding Fuel If the coal bed is not hot and glowing, rake the coals to the front of the stove, close the door and adjust the air inlet control to the wide open position. Let the coals re-heat for 10–15 minutes. When hot and glowing, spread them out and place your next fuel load into the stove (make sure no coals or ashes block the LPAO). Leave the door air inlet control in the wide open position for 15–20 minutes.
PAGE 13
Service Hints cont’d... Preventing Creosote Buildup 1. Burn with air control open for several minutes at numerous intervals throughout the day during the heating season, being careful not to overfire the unit. 2. Burn stove with air inlet control wide open for 15–20 minutes every time you apply fresh wood. This allows wood to achieve the charcoal stage faster and burns wood vapors which might otherwise be deposited within the heating system. 3. BURN ONLY SEASONED WOOD. Avoid burning wet or green wood.
PAGE 14
Service Hints cont’d... Glass Care The following usage and safety tips should be observed: 1. Inspect the glass regularly for cracks and breaks. If you detect a crack or break, extinguish the fire immediately and contact the manufacturer for a replacement. 2. Do not slam the door or otherwise impact the glass. When closing doors, make sure that logs or other objects do not protrude to impact the glass. 3. Do not build fires against (or that might fall against) the glass. 4.
PAGE 15
Wiring Diagram - TR008 Durango Blower Assembly When ordering missing or replacement parts, always give the Model Number of the stove, Part Number, and Part Description. Use the illustrations and part lists provided to identify parts. TR008 / 050207.
PAGE 16
Parts - TR008 Durango High-Efficiency stove When ordering missing or replacement parts, always give the Model Number of the stove, Part Number, and Part Description. Use the illustrations and part lists provided to identify parts. Page 16 / DURANGO™ TR008 / 050207.
PAGE 17
Parts - TR008 Durango High-Efficiency stove When ordering missing or replacement parts, always give the Model Number of the stove, Part Number, and Part Description. Use the illustrations and part lists provided to identify parts. Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Qty. Part No. Description Qty. Main Fire Box Assembly................................ 1 Back Heat Shield Assembly.......................... 1 Door Assembly (see pg 17 for parts)............. 1 Front Heat Shield Curtain........
PAGE 18
Parts - TR008 Durango High-Efficiency stove When ordering missing or replacement parts, always give the Model Number of the stove, Part Number, and Part Description. Use the illustrations and part lists provided to identify parts. Part No. Description Qty. 3 Door Assembly (complete).............................. 1 41 Door Casting.................................................. 1 42 Air Wash Casting............................................. 1 43 Door Vent Slider................................
PAGE 19
Chimney Connector Systems & Clearances A. Brick Masonry Minimum 3.5-inch thick brick masonry all framed into combustible wall with a minimum of 2-inch brick separation from clay liner to combustibles. The fireclay liner shall run from outer surface of brick wall to, but not beyond, the inner surface of chimney flue liner and shall be firmly cemented in place. B.
PAGE 20
Floor Protector Material Calculations This stove has been tested for and must be installed on a floor protector with the proper Thermal Resistance or R-value as stated in the installation instructions on page 3, “Locating Stove” step 1, of this manual. If the floor protector materials listed in the instructions are not available, materials with an equivalent R-value may be substituted.
PAGE 21
TR008 / 050207.
PAGE 22
This Vogelzang heating appliance is safe when installed properly and will provide you with years of service. However, always exercise good judgement when you are using this stove. You are dealing with FIRE! Fire is inherently dangerous and must be treated with respect.