Instruction Manual

ManualsBrandsVogelzang ManualsKilnVG820E (new as of 2013)

OWNERS MANUAL

Model VG820E

THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR

SAFETY NOTICE:

If this heater is not properly installed, a house  re may result.

For your safety, follow the installation directions.

Contact local building or  re o cials about restrictions and

inspection requirements in your area.

CAUTION:

Read all instructions carefully before starting the installation

or operation of this heater.

Improper installation may void your warranty.

*ASSEMBLY

*INSTALLATION

*OPERATION

*REPAIR PARTS

852084

HOW TO ORDER REPAIR PARTS

 is manual will help you to obtain e cient, dependable service from

the heater, and enable you to order repair parts correctly.

Keep this manual in a safe place for future reference.

When writing, always give the full model number which is on the

nameplate attached to the inside of the cabinet door of the heater.

Heartwood

When ordering repair parts or options, always give the

following information as shown in this list:

1.  e PART NUMBER

2.  e PART DESCRIPTION

3.  e MODEL NUMBER: VG820E

4.  e SERIAL NUMBER:________________

Before installing your heater,  ll in the serial number of your heater

in the space provided above.

United States Stove Company

227 Industrial Park Rd.

P.O. Box 151 South Pittsburg, TN 37380

(800) 750-2723

www.vogelzang.com

United States Stove Company

227 Industrial Park Rd.

P.O. Box 151 South Pittsburg,

TN 37380

(800) 750-2723

www.vogelzang.com

DO NOT USE THIS HEATER IN A MOBILE HOME OR TRAILER

Tested to UL 1482 & EPA Method 28A

OMNI-TEST LABORATORIES, INC.

LISTED BY

PORTLAND

OREGON, USA

Report #: 215-S-14-4

Summary of content (10 pages)

PAGE 1
OWNERS MANUAL Model VG820E HOW TO ORDER REPAIR PARTS This manual will help you to obtain efficient, dependable service from the heater, and enable you to order repair parts correctly. Keep this manual in a safe place for future reference. THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR When writing, always give the full model number which is on the nameplate attached to the inside of the cabinet door of the heater.
PAGE 2
TOOLS AND MATERIAL NEEDED TOOLS Pencil 6 Foot Folding rule or tape Tin Snips Drill, hand or electric Drill bit, 1/8" dia. (for sheet metal screws) Gloves Screwdriver (blade-type) 5/16" Nut Driver or 5/16" Socket w/Ratchet ELECTRICAL 120 Volts 60 Hertz 0.55 Amps NOTES MATERIALS Chimney Connection- 6" Dia. Black Steel (24 Ga.
PAGE 3
CB36 BLOWER KIT 4. An Optional Blower kit is available for the VG820E Heartwood automatic wood burning circulator heater. If this kit is not available where you have purchased this Heartwood heater, you can purchase a blower kit directly from the factory. To order contact Vogelzang at the address and telephone number given on the back page. Route power cord away from unit. Do not route power cord through walkway. 5. 6. Blower operation Rotate knob clockwise to increase airflow.
PAGE 4
heater or chimney connector. The 1 inch air space provides free air circulation. It is essential that there be openings at the top and bottom of these clearance reducers so cool air can enter at the bottom and hot air exit at the top. It is the "chimney effect" whereby when the air in the space is heated, it rises exiting from the top and being replaced by cooler air at the bottom, that makes these shields effective.
PAGE 5
REPAIR PARTS LIST - MODEL VG820E AUTOMATIC WOOD BURNING CIRCULATOR INTERIOR Key Part No. 1 67859 Weldment, Base Description Qty. 1 2 22030 Shield, Second Heat (Included w/ 67859) 1 3 22110 Shield, Heat (Included w/ 67859) 1 4 68619 Assy.
PAGE 6
FIG. 6A - Thru-The-Wall Installation REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER NON-COMBUSTIBLE WALL MODEL NUMBER VG820E THIMBLE EXTERIOR REPAIR PARTS LIST COLLAR PIPE DAMPER BAROMETRIC DRAFT CONTROL (OPTIONAL) CLASS A UL 103HT CHIMNEY KIT INCLUDING WALL THIMBLE. FLOOR PROTECTOR FIG. 6B - Typical Masonry Chimney Installation APPROVED COWL 2 FT MIN. 10 FT. MINIMUM 6" MIN. 3 FT. MIN. APPROVED THIMBLE 60" MIN. DAMPER BAROMETRIC DRAFT CONTROL 6" MIN. FLOOR PROTECTOR 6 KEY NO.
PAGE 7
VENTING INTO A FIREPLACE (Not recommended) REPAIR PARTS - EXTERIOR Many prefabricated fireplaces fall into the "zero-clearance fireplace" category. This is a factory metal fireplace with multi-layered construction. It is designed to provide enough insulation and/or air cooling so that the base, back and sides can be safely placed in close contact with combustible floors and walls.
PAGE 8
FIREPLACE INSTALLATION SERVICE HINTS Connection of the stovepipe directly into the existing masonry chimney over the fireplace opening is the only approved method. This installation performs better, yielding easy to clean and inspect for creosote. Before beginning this type of installation plan carefully; a high degree of skill is required to insure safety. Install the stovepipe as far as possible into the thimble, but not past the inside of the flue lining.
PAGE 9
CABINET DOOR KNOB ASSEMBLY The door knob is mounted inside of the cabinet door to facilitate shipping and must be reversed for proper usage. To get cabinet door open, place hand under cabinet frame (right hand side of cabinet door) and push door out. INSTALL THE CABINET DOOR KNOB USING THE STEPS BELOW: 1. Remove the machine screw and door knob (Fig. 10). 2. Place door knob on outside of cabinet door. Then place machine screw through hole and into door knob and tighten (Fig. 11).
PAGE 10
RULES FOR CONNECTOR PIPE INSTALLATION 1. The crimped end of the stovepipe fits inside the heater flue collar. Install additional pipe and elbow with the CRIMPED END TOWARD THE HEATER. This will allow any condensation in the flue to run back into the heater. Smoke will not escape when installed in this manner. 5. Seal each connector pipe joint with furnace cement. Also seal the pipe at the chimney. 6. Use 3 Sheet Metal screws at each joint to make the piping rigid. 2.