AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 AudioMate 360r User Guide AM360r IP Voice Gateway for Land Mobile Radio www.VoiceInterop.com Table of Contents Quick Start Guide..................................................................................................2 Gather Your Tools Basic Configuration Steps AudioMate 360r Product Tour.............................................................................3 Front Panel Rear Panel Installation........
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Quick Start Quick Start Guide Gather Your Tools Web browser — Mozilla Firefox, Opera, Chrome, or Internet Explorer. AM360 Configuration Utility www.voiceinterop.com Register as a customer Choose the Support tab. Download AudioMate 360 IP Address Assignment utility AM360 Configuration Utility — To find the address of each AM360 gateway, download the AudioMate 360 IP Address Assignment utility from our web site, www.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 tour AudioMate 360r Product Tour Front Panel Front Panel Indicators All front panel indicator LEDs can display one of seven color states: OFF, RED, RED FLASHING, GREEN, GREEN FLASHING, AMBER and AMBER FLASHING each of which can be used to indicate a different condition within the AudioMate 360r. www.VoiceInterop.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Front Panel Connections There are no connections to the front panel of the AudioMate 360r. Front Panel Controls There are no input controls on the front panel of the AudioMate 360r. Rear Panel Rear Panel Indicators LAN Port — The LAN jack has two built-in lamps: a solid green one indicating that an electrical link has been established, the other flashing green indicating packet activity.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 The Mate-N-Lok jack is connected in parallel to daisy chain other AM360 gateways from a larger power supply. The top 2 pins are +12 Volts, the bottom two are Ground. Rear Panel Controls Reset — This recessed push button reboots the processor in the AudioMate 360. Depress using a pen or any object with a small tip.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 AM360 Config Utility The Address Finder utility is available to registered users by logging in to our web site: www.voiceinterop.com Click the Support tab. Locating the AM360 Address Use the AudioMate 360 Configuration utility to locate the addresses of your units in preparation for configuration. Individual AudioMate 360 units are configured via web browser pointed to the management IP address of the unit.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Global Configuration In the menu pane on the left, locate the Configuration heading and click the link Global under it. The screen labeled AM360 Configuration should appear in the right pane. You may safely ignore the AMCP settings. This Unit’s Name allows you to set a memorable name to identify this unit among the others on your network. This field accepts standard alphanumeric characters.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Save Your Changes Update Unit button — When you are satisfied with all the settings that appear on the Global Configuration page, be sure to click on the button labeled Update Unit at the top of the page. Your new settings take effect immediately, except for the fields labeled IP Boot. The IP Boot fields only take effect after a reboot.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 COS (Carrier-Operated Switch) will stream audio to the IP network when the COS digital input is asserted, either on the Single-Ended COS logic line or the E-lead of the balanced audio interface. Tone Remote Control Set Receiver to VoIP Mode to ON to send RTP audio packets full time to the radio end of the link.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Receive Gain accepts a number from 0 to 63 representing 64 steps of gain or attenuation in the audio line from the attached radio receiver. Level 0 represents the lowest audio level while 63 represents the highest audio level. Every installation is unique, adjust for your installation for proper operation. Default is 31.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Transmit Pre-Emphasis Enable (default cleared) will apply a 6 dB per octave high pass filter to the transmit audio stream from the IP network to the transmitter audio of the attached radio. Check the box to apply this filter or clear the check box to allow the transmitted audio to pass unprocessed (flat audio).
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 status Status The AudioMate 360 family of IP gateways provide status pages to make adjustments and diagnostics easier. The AudioMate 360r provides the means to view the status of the digital input and output signals as well as to view the configured transmit and receive audio levels. Global Status The Global Status page displays various parameters of the common interface board.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 IP Mode shows whether the unit received its address from a DHCP server or is configured with a static IP address. IP Address shows the currently assigned IP address regardless of how it was obtained. Module Status Troubleshooting If you have trouble interfacing the AM360r with your radio, the Module Status screen and front panel LED indicator lamps can quickly tell you what is and isn’t working as expected.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 PTT Output indicates whether this digital output line is asserted, shown as Key, or whether it is idle. If troubleshooting and this indicates Key yet the attached radio does not transmit, check the wiring of the interface cable and whether the radio requires an active low or active high signal to key the transmitter. Mic Output indicates the state of the M-lead on the balanced audio port.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 specs Daisy Chain To power up to 8 AM360 gateways from a single supply, use Tyco Mate-N-Lok plug shell #794617-4 and pins #1-794610-1 with 20 gauge stranded wire. The current should not exceed 5 Amps. The power supply should be rated for at least 8 Amps. AudioMate 360r Specifications Physical Form factor Stand-alone unit Dimensions 1.75 in. (4.5 cm) H x 3.6 in. (9.2 cm) W x 5.2 in. (13.2 cm) D Weight 0.8 pounds (0.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 A Appendix A - Interface Examples Ritron Nexus Radio Base The Ritron NRB is a small, lightweight radio available in VHF and UHF bands that is wellsuited to demonstration use. It interfaces with the AudioMate 360r via a straight–through standard Category 5 LAN cable on the hardrware revision B and later units. Not Working? Configure Ritron radio E&M jumpers to positions A, C, E for proper operation.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Motorola Waris Series Most Motorola mobile radios in the Waris series (CM and CDM models) use the same pinouts for basic interfacing via a 16-pin accessory connector on the rear apron. A number of the accessory pins are programmable in the radio using Motorola’s closely guarded CPS programming software. Not Working? Proper programming of radio accessory pins is ESSENTIAL to interface with Motorola radios.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 B Appendix B Multicast Addressing Notes Note 1: Avoid addresses of the form 224.0.0.x Traffic to addresses of the form 224.0.0.x is often flooded to all switch ports. This address range is reserved for link-local uses. Many routing protocols assume that all traffic within this range will be received by all routers on the network. Hence (at least all Cisco) switches flood traffic within this range.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 C Appendix C - WAVE Configuration WAVE (Wide Area Voice Environment) from Twisted Pair Solutions provides the glue to tie together your various IP voice communications endpoints. The AudioMate 360 family of IP voice gateways works seamlessly with WAVE to extend your communications options and enhance interoperability among disparate devices.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Channels (WAVE 4) Log in to WAVE. Click Media Servers -> Interfaces, then click the Add Interface button. From the dropdown listbox select VoiceInterop AM360 and click the Next button. In the Name field type a meaningful name. Tab to the Description field and type a meaningful description. In the Gateway IP Address field type the management address of the AM360 that will be associated with this endpoint.
AM360r User Manual revised 2014.02.29 for Hardware Rev. DD Firmware Version 1.00.26 Under Configuration click Global. In the field RTP Remote IP type the unicast address of the target media server. For RTP Remote Port and RTP Local Port type a port number between 16384 and 65534; both fields should be identical numbers. For Codec select G.711u; if your network will not support about 100kbps streams then select GSM. Click the button Update Configuration to save your changes.
