Users Manual

ManualsBrandsVolansys ManualsNetwork HardwareEnterprise/Industrial IoT Gateway

User Guide (UG)

CENTAURI-200

Revision: 1.6

Date: 23-11-2020

Volansys Technologies Private Limited

Block A 7th Floor, Safal Profitaire, Corporate Road,

Prahladnagar, Ahmedabad 380015, India

www.volansys.com

Phone: 91-79-4004-1994

Email: info@volansys.com

Confidentiality Notice

This document is authored by Volansys and is Volansys’ intellectual property, including the copyrights in all countries in the world. This

document is provided under a license to use only with all other rights, including ownership rights, being retained by Volansys. This file may not

be distributed, copied, or reproduced in any manner, electronic or otherwise, without the express written consent of Volansys.

Summary of content (21 pages)

PAGE 1
User Guide (UG) CENTAURI-200 Revision: 1.6 Date: 23-11-2020 Volansys Technologies Private Limited Block A 7th Floor, Safal Profitaire, Corporate Road, Prahladnagar, Ahmedabad 380015, India www.volansys.com Phone: 91-79-4004-1994 Email: info@volansys.com Confidentiality Notice Copyright © 2020Volansys – All rights reserved. This document is authored by Volansys and is Volansys’ intellectual property, including the copyrights in all countries in the world.
PAGE 2
TABLE OF CONTENTS CENTAURI-200 User Guide 1 INTRODUCTION........................................................................................................................................................... 5 1.1 PURPOSE..................................................................................................................................................................5 1.2 SCOPE................................................................................................................
PAGE 3
CENTAURI-200 User Guide LISTS OF TABLES TABLE 1 GATEWAY LED INDICATION.................................................................................................................................... 12 TABLE 2 GATEWAY SWITCH FUNCTION..................................................................................................................................13 LISTS OF FIGURES FIGURE 1- 1 GATEWAY SETUP ARCHITECTURE....................................................................................
PAGE 4
Revision History Date 10-Aug-2019 29-Aug-2019 12-Dec-2019 Version Draft 0.1 1.0 1.1 06-02-2020 04-03-2020 1.2 1.3 13-03-2020 1.4 06-08-2020 1.5 23-11-2020 1.6 VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 CENTAURI-200 User Guide Details of change Initial Draft First Release Updated IoTiFy link in Section 3 Updated section 4.3 Corrected LED2 indication in chapter 4.
PAGE 5
CENTAURI-200 User Guide 1 INTRODUCTION This document will guide an end user in getting started with the CENTAURI-200. 1.1 Purpose This document will address the following things: 1. 2. 3. 4. 1.2 Getting Started with CENTAURI-200 demonstration System Overview CENTAURI-200 Gateway Setup End device setup and control Scope The scope of the guide is to describe the various functionalities to configure CENTAURI-200 using mobile application for the user.
PAGE 6
EUI OTA 1.4 Extended Unique Identifier Over The Air References Reference Document Title NA 1.5 CENTAURI-200 User Guide Provided by Remarks Document Conventions This element signifies a useful information or tip or suggestion This element signifies a warning or proceed with caution This element signifies that the action should be avoid VT-ENG-TMP-UG | Rev 1.
PAGE 7
1 CENTAURI-200 User Guide SYSTEM OVERVIEW CENTAURI-200 Gateway is a central device to run the out of the box demonstration. To do the setup, the user needs to provide Internet connectivity to CENTAURI-200 Gateway. The Gateway supports Ethernet, WiFi and LTE to connect to the cloud. The user can add end devices in the system using mobile application. Once the end devices are added to the system, the user can control them via the mobile application.
PAGE 8
CENTAURI-200 User Guide 2 MOBILE APPLICATION SETUP 2.1 Installation (Android Mobile Application) 1. The IoTify Android application is available on Google Play Store. 2.2 Installation (iOS Mobile Application) 1. The IoTify iOS application is available on the Apple Application store. VT-ENG-TMP-UG | Rev 1.
PAGE 9
CENTAURI-200 User Guide 2.3 Initial setup and User registration 1. Launch/open installed application in the mobile. User can see below screen Figure 3- 1 Mobile Application Launch Page 2. If prompted for any permission, please allow. 3. Follow user registration process for creating account. Enter verification code received on email to complete registration process. VT-ENG-TMP-UG | Rev 1.
PAGE 10
CENTAURI-200 User Guide Figure 3- 2 User registration for Gateway 4. Login with the user credential created during sign-up. 5. On successful authentication, user is redirected to the list of registered gateways. The user can see registered gateway if any or can see below screen without any gateways. VT-ENG-TMP-UG | Rev 1.
PAGE 11
CENTAURI-200 User Guide Figure 3- 3 Home screen after successful login VT-ENG-TMP-UG | Rev 1.
PAGE 12
3 CENTAURI-200 User Guide GATEWAY SETUP 3.1 Gateway LED indication LED Indication POWER LED LED1 ON Power is available OFF No Power supply is connected OFF Access Point mode is off SOLID RED Access Point mode is on. Blinking RED End Device Commissioning in progress (1 second off, 1 second on) LED2 Represents Green Internet connectivity available Red Internet connectivity NOT available Table 1 Gateway LED indication 3.
PAGE 13
CENTAURI-200 User Guide Table 2 Gateway Switch function 3.3 Gateway Initial setup Follow below steps for initial Gateway setup 3.3.1 1. 2. 3. 4. Gateway Setup with Wi-Fi Plug in power cable in DC power input port of gateway available on back panel. Plug-out Ethernet cable if it is plugged in. Power up the Gateway. After power up, Gateway will be in Access point mode. It will broadcast SSID = Centauri_XXXX (XXXX = Last 4 digit of MAC address). 5. Observe the LED indication.
PAGE 14
CENTAURI-200 User Guide Figure 4- 1 CENTAURI-200 Gateway 3.4 Gateway Commissioning [Registration] A user needs to register the gateway using the mobile application to use the gateway to control and monitor end devices. To register the gateway, follow below ste ps. 3.4.1 Gateway Registration 1. Open the mobile application and log in using user id. User can see below screen in mobile application if none of the gateway is registered previously with same user id. 2.
PAGE 15
CENTAURI-200 User Guide Figure 4- 2 IoTify Dashboard Once user connects to access point of the GW, the user needs to enter the Wi-Fi password as centauri_XXXX (XXXX=Last 4 digit of Gateway MAC, e.g. “centauri_D1A5”). After the user comes back to this application, user will see below screen. In this screen, user shall select an Access point that GW will use for getting an internet connectivity. (E.g. Home Wi-Fi router access point).
PAGE 16
CENTAURI-200 User Guide Figure 4- 3 Gateway Provisioning 1. After providing all correct input, the gateway will be commissioned, and it will be available on application as shown below. User can add multiple gateway to the application by following same process. VT-ENG-TMP-UG | Rev 1.
PAGE 17
CENTAURI-200 User Guide Figure 4- 4 Gateway List 2. Long press on Gateway and select Gateway information. This will open Gateway property window. User can rename the gateway in this screen. VT-ENG-TMP-UG | Rev 1.
PAGE 18
Figure 4- 5 Gateway property change CENTAURI-200 User Guide 3.4.2 Factory reset the gateway 1. SW2 switch can be used (long press) to factory reset the gateway if needed. Refer Gateway Switch indication for more details Figure 4- 6 Gateway Wi-Fi reset button o o User can see LED2 will turn green if Gateway has internet connectivity. LED2 will be red if there is not internet connectivity VT-ENG-TMP-UG | Rev 1.
PAGE 19
CENTAURI-200 User Guide 3.5 Change Gateway Network Interface for IP connectivity (Wi-Fi or Ethernet) 3.5.1 Change from Wi-Fi to Ethernet Follow below steps to change Network interface from Wi-Fi to Ethernet 1. Press SW2 switch more than 5sec to factory reset the Gateway. See if LED2 turns Red. 2. Plug in Ethernet cable to Gateway board. 3. Observe LED indication on Gateway board.
PAGE 20
CENTAURI-200 User Guide 3.6 Remove Gateway To remove Gateway from registered gateway list, follow below steps. 1. The gateway must be powered on and connected to the cloud. Confirm LED2 must be solid green. GW should be shown Green on mobile application as well. 2. Open Mobile application and select the Gateway to be removed. Figure 4- 7 Remove Gateway VT-ENG-TMP-UG | Rev 1.
PAGE 21
CENTAURI-200 User Guide 3.7 FCC/IC Warning This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should beinstalled and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located oroperating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules and RSS-247 of Industry Canada.