8-port 10/100Base-TX +2-port 100Base-FX Switch (INS-802 / INS-802W) User Manual
COPYRIGHT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written permission of the publisher. FCC WARNING This equipment has been tested and found to comply with the limits for a class A device, pursuant to part 15 of FCC rules.
TABLE OF C ONTENTS ABOUT THIS GUIDE............................................................ 4 TERMS/USAGE ....................................................................... 4 INTRODUCTION ................................................................... 4 INDUSTRIAL ETHERNET TECHNOLOGY .................................. 5 SWITCHING TECHNOLOGY ..................................................... 5 FEATURES ..............................................................................
A BOUT T HIS G UI DE The INS-802/INS-802W Industrial Series Switch is a hardened, 8-port Ethernet Switch with dual fiber uplinks and redundant DC power inputs – to provide a reliable and economical solution for your industrial Ethernet environment. With its dry contact smart alarm, the INS-802/802W can initiate a physical alarm (audible and/or visible) in the event of a malfunction.
Industrial Ethernet Technology The growing importance of Ethernet has extended to the factory floor and industrial environments, where things have become too harsh for typical commercial-grade networking equipment. VOLKTEK has created an Industrial Series of Switches and interconnecting devices specifically for the purpose of extending Ethernet to the factory floor and industrial environments.
Features The Switch was designed for easy installation and high performance in an industrial environment where vibration, shock, heat, and RF interference may be commonplace. The Switch was specifically designed to be small and compact for easy DIN-rail mounting and it can be installed where space is limited. The Switch is ideal for deployment with multiple high-speed servers for shared-bandwidth 10Mbps or 100Mbps workgroups.
o o o o o o o o Power terminal block Wide voltage range: 9-48V DIP Switch to enable or disable alarm functions Power-input polarity protection function Under-power and over-power detection function Wide operating temp.: -10°C - 70°C / -40°C - 70°C (802W) Store-and-forwarding Auto-negotiation at all copper ports INS-802 I NDUSTRIAL S WITCH – U NPACKI NG AND S ET- UP This section and the following sections explain the set-up and installation of the VOLKTEK INS-802/802W Industrial Switch.
Layout of the INS-802/802W Front View of Switch 1. Fiber Port Offline LED x 2 2. Fiber Port LNK/ ACT x 2 3. Fiber 100Mbps LED x 2 4. Primary Power LED 5. Redundant Power LED 6. Alarm LED 7. 2 x 100Base-FX LC Fiber slots (SFP-type) 8. 10/100Base-TX ports (8) 9. TX Port 100Mbs LED 10.
TOP View of Switch Grounding Screw Terminal block for power input (PWR/RPS), and alarm dry contact DIP Switches Back View of Switch Din Rail Bracket Screws 9
DIN Rail Mounting of the INS-802/802W The aluminum DIN-rail attachment plate should already be affixed to the back panel of the Switch. If you need to attach the DIN-rail plate, assure that the stiff metal spring is situated towards the top.
• • from the Switch. Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Grounding the INS-802 Industrial Switch will help minimize noise due to electromagnetic interference (EMI). Always run the ground connection from the ground screw to the grounding surface prior to connecting DC power.
DC Powered Switch: Power is supplied through an external DC power source. Check the technical specification section for information about the DC power input voltage. Since the switch does not include a power switch, plugging its power adapter into a power outlet will immediately power it on.
Procedure for Connecting DC Power: For shipping, the removable green Contact Block may be detached from the six-pin terminal contact point. It may be easier to attach the DC wires to the green Contact Block if it has first been unplugged from the terminal contact point on the switch. A. On the Power Contact Block, use a flathead screwdriver to loosen the screws of the primary power pins (labeled PWR +/-) and then insert the negative and positive DC wires. Tighten until snug. B.
used to connect to Ethernet-enabled devices. The Fiber ports use LC SFP-type Single-mode or Multi-mode modules, which are sold separately. LED Indicators Switch Status LED Power Indicator (PWR) / Redundant Power Supply (RPS) These LEDs light green when the Switch is receiving power from these sources. Otherwise, they are off. Alarm (ALM) This indicator will light red and will initiate a physical alarm (if such an alarm is connected) if a link failure occurs on any port.
10/100Base-TX ports There are two eagle-eye LED’s on each 10/100 port. The top LED will illuminate green if the link speed is 100Mbps, and the lower LED will illuminate green if there is link activity. Otherwise, the LED’s will be off. External Alarm Contact The INS-802 Industrial Switch has one Alarm Contact connection point located on the green Power Contact Block on the top panel.
2. Ports 9~10: link failure (e.g.: cable disconnected, device breakdown, etc.) Note: The alarm function is disabled when the SFP fiber module is absent. 3. PWR/RPS: Power failure a. Power cord is disconnected, power supply malfunction, etc. b. Input power is out of the range listed in the spec (9 ~ 48V) DIP Switch Settings DIP-switches allow for the user to manually turn ON/OFF any port, the external Alarm, or the redundant power supply. The figure below shows the DIP-switch control.
Recommended Procedure for configuring and setting DIP switches during initial installation: 1. Turn all DIP switches OFF. 2. Install the INS-802 into your network. 3. Decide which port(s) need to be monitored or should trigger the alarm. 4. Turn the corresponding port DIP-switch ON. 5. Activate the Switch. Fiber Connector The dual Fiber Ports on the INS-802 are LC-type SFP modules in either multi-mode or single mode (sold separately).
determine the fastest data transmission rate supported by both devices. This helps make the Switch a plug-andplay device. The Switch’s RJ-45 ports support full or half duplex, depending on which transmission speed is supported by the attached device.
mode for the new twisted-pair connection: If the connected device does not support auto-negotiation or has auto-negotiation disabled, an auto-sensing process is initiated to select the speed and set the duplex mode to half-duplex. T ECHNICAL S PECIFICATIONS General Standards IEEE 802.3 IEEE 802.3u & IEEE 802.
Physical and Environmental DC inputs 9-48V DC Temperature Operating: -10° ~ 70° C, Storage: -20° ~ 80° C (INS-802W) Operating: -40°° ~ 70°° C, Storage: -40°° ~ 85°° C Humidity Operating: 5% ~ 85% Dimensions 120 x 50 x 162 mm (D x W x H) Compliance FCC Class A, CE approved Performance Transmission Method: Store-and-forward, with IEEE802.3x full duplex, non-blocking flow control.
A PPENDIX RJ-45 Pin Specification The RJ-45 ports in the Switch support auto-negotiation and auto MDI/MDI-X. This feature eliminates worries about using a specific cable type.
The standard cable, RJ-45 pin assignment The standard RJ-45 receptacle/connector VOLKTEK CORPORATION 4F, No.
