INSTALLATION INSTRUCTIONS VOLT® Low Voltage Landscape Lighting VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ Help Hotline: 1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST) Specifications and product details subject to change without notice. © Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@voltlighting.com • 813.978.
INSTALLATION INSTRUCTIONS VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ ! Important: Please Read Before Installation This fixture is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty. These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations. 1.
Package Contents A. (1) Fixture B. (1) PVC Tube Product Dimensions 6.25” 8.25” 5.5” customersupport@voltlighting.com • 813.978.
INSTALLATION INSTRUCTIONS VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ 1 Dig Hole PVC Tube Dig a hole in the ground. Make sure there is approximately 3 inches surrounding the PVC Tube for pea gravel or sand on all sides. 3” 3” 3” Hole Soil 2 Wire Connection PVC Tube Fixture Place the fixture into the PVC Tube and pass the luminaire pigtail through the PVC Tube. Strip both leads from the luminaire pigtail.
3 Fill Pea Gravel or Sand Pea Gravel or Sand Install the PVC Tube with the fixture in the hole and fill around the fixture securing it in place with pea gravel or sand to allow for water drainage. PVC Tube with Fixture Now you can power on the system, and the light is 2700K and the optic is 60 degree as default. Soil Install/Replace Optic 1 Remove Luminaire from bracket Screw By using the Allen wrench, loosen the screw in the handle and remove the luminaire from the bracket.
INSTALLATION INSTRUCTIONS VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ 2 Remove Faceplate and Lens Screw Loosen all screws on the faceplate. Remove the faceplate and lens from the fixture. Faceplate Lens fixture 3 Replace Optic Loosen the screws and remove the optic from the fixture. Screw Optic fixture Install the new optic in the fixture. Make sure that you have the optic properly aligned over the LED board before tightening down.
4 Reinstall Luminaire to bracket Place the luminaire between the brackets. Pass previously removed screws through the handle and bracket. Thread the screws back onto the luminaire. Hand tighten until snug with the Allen wrench. Screw Handle Allen Wrench Bracket Luminaire IR Remote (Optional) An IR Remote is optional for this fixture. The IR remote requires two AAA batteries.
INSTALLATION INSTRUCTIONS VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ 2 Install Two AAA Batteries AAA Battery Battery Compartment Place two AAA batteries into the battery compartment properly. + - + - IR Remote 3 Backing Install the Battery Compartment Cover 2 Place the battery compartment cover back onto the IR Remote. Tab Cover 1 IR Remote Backing w w w. v o l t l i g h t i n g .
4 IR Remote Functions 1. 2. 3. 4. 5. 3 2 OFF 1 ON G R 4 B W FLASH 5 STROBE 6 FADE 7 SMOOTH 8 On Off Brightness Control 16 color selections Flash • Mode 1: Repeats Red, Green, Blue + color cycle for 1 second duration of each of the seven colors within this mode. • Mode 2: Hit flash a second time and this mode slowly blends the same seven colors from mode one, mixing them together. 6.
INSTALLATION INSTRUCTIONS VOLT® RGBW Salty Dog Integrated LED Brass Well Light (Bronze) VWL-7125-BBZ w w w. v o l t l i g h t i n g .
customersupport@voltlighting.com • 813.978.
Help Hotline: 1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST) w w w. v o l t l i g h t i n g . c o m Specifications and product details subject to change without notice. © Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@voltlighting.com • 813.978.
