DSP-3005V Single Channel DC Power Supply User Manual
Table of Contents 1. General Safety Requirements ......................................................... 1 2. Safety Terms and Symbols .............................................................. 2 3. Quick Review .................................................................................... 3 3.1 Panel and Interface ............................................................................ 3 3.1.1 Front Panel ......................................................................................
1.General Safety Requirements 1. General Safety Requirements Before use, please read the following safety precautions to avoid any possible bodily injury and to prevent this product or any other connected products from damage. To avoid any contingent danger, ensure this product is only used within the ranges specified. Only a qualified person should perform internal maintenance. To avoid Fire or Personal Injury: ◼ Use Proper Power Cord.
2.Safety Terms and Symbols 2. Safety Terms and Symbols Safety Terms Terms in this manual (The following terms may appear in this manual): Warning: Warning indicates conditions or practices that could result in injury or loss of life. Caution: Caution indicates the conditions or practices that could result in damage to this product or other property. Terms on the product. The following terms may appear on this product: Danger: Indicates an immediate hazard or injury possibility.
3.Quick Review 3. Quick Review 3.1 Panel and Interface 3.1.1 Front Panel 1 2 11 3 10 4 9 5 6 8 7 Figure 3-1 Front Panel Overview 1 Display Area Display user interface. 2 Current Key Set current parameters, press to move the cursor when editing parameters 3 Knob Select the main menu or change the value, function equals to the confirmation key.
3.Quick Review 5 Memory Key 5 sets of channel parameters can be stored for quick output, or long press to enter the List waveform output editing interface. 6 On/Off Key Turn on/off the channel, or long press to turn on or turn off the power-on automatic startup function. 7 Channel Output Terminal Output access of channel.
3.Quick Review 1 Air Vent Air vent. 2 Power Button Turn on/off the instrument. 3 Fuse Power fuse. 4 AC Power Input Jack AC power input interface. 5 Device USB Port Update the firmware, PC software control port. 3.1.3 User Interface CV: Constant Voltage output Display cumulative CC: Constant Current output running time Actual output power Channel output status Actual voltage output Actual current output Set values of voltage Set values of O.C.P Set values of current Set values of O.V.
3.Quick Review The supplied accessories have been already described in the "Appendix A: Accessories" of this Manual. You can check whether there is any loss of accessories with reference to this description. If it is found that there is any accessory lost or damaged, please get in touch with the distributor of our responsible for this service or our local offices. 3.
3.Quick Review (3) Set some different voltage values on this channel; check if the actual voltage value displayed is close to the set voltage value, and also that the actual current value displayed is nearly to zero. (4) Check that if the output voltage can be adjusted from zero to the maximum rating. When it is set to the maximum or minimum, a beep is heard, indicating that the limit has been reached. 3.4.
4.Panel Operation 4. Panel Operation 4.1 Turn On/Off the Channel Output Press the On/Off key to turn on/off the channel; 4.2 Set the Output Voltage/Current In the channel setting area, press the V / I key to move the blue cursor between different positions of the voltage/current value. After pressing the output voltage/current setting value, turn the knob to change the value of the current cursor, and press the knob or press the V / I key to move the cursor.
4.Panel Operation Set values of O.V.P Set values of O.C.P 4.4 Memory key shortcut settings Press the Memory key on the front panel to store 4 sets of channel parameters M1, M2, M3, and M4 respectively for quick output. 4.4.1 Quick output To output a set of parameters from M1 to M4, follow these steps: (1) Press Memory key on front panel, the shortcut interface will display. (2) Turn the knob and a gray selection box appears. Turn the knob to move the gray selection box.
4.Panel Operation voltage protection / over current protection value. (4) Turn the knob to change the value of the current cursor, press the knob or press the V / I / OVP / OCP key to move the cursor. Set values of voltage Set values of O.V.P Set values of current Set values of O.C.P 4.5 Set List Waveform Output The user can edit and output the waveform. A set of waveforms contains 10 editable points.
4.Panel Operation move the cursor position; short press the Memory function key on the front panel to exit the parameter setting status； （5） In the non-parameter setting state, press the knob for 3 seconds to confirm, enter the "List Waveform Output Mode", and at the same time, switch back to the main interface; （6） Long press the Memory function key on the front panel for 3 seconds to exit the "List waveform editing interface". 4.5.
4.Panel Operation 4.6 Set Automatic Output at Power-on The user can turn on or turn off the "automatic output at power-on" function by pressing and holding the On/Off function key for 3 seconds. （1） The steps are as follows. The user can turn on or turn off the "automatic output at power-on" function by pressing and holding the On/Off function key for 3 seconds. The steps are as follows: （2） When the "automatic output at power-on" is turned off, after power-on, the instrument is in the standby state.
4.Panel Operation number or curve. Number Press the Display function key to set the display mode to Number. When the power supply is powered on, the default display mode is Curve. Curve Press the Display function key to set the display mode to Curve.
5.Troubleshooting 5. Troubleshooting 1. The instrument is powered on but no Display. ⚫ Check if the power is connected properly. ⚫ Check if the fuse which is below the AC Power socket is used appropriately and in good condition (the cover can be pried open with a straight screwdriver). ⚫ Restart the instrument after the steps above. ⚫ If the problem still exists, please contact us for our service. 2. The output is abnormal: ⚫ Check if the output voltage is set to 0V. If so, set it to other value.
6.Technical Specification 6.
6.Technical Specification Setting Resolution Voltage Current 10mV 1mA Readback Resolution Voltage 10mV Current 1mA Setting Accuracy Voltage ≤0.1%±20mV Current ≤0.1%±10mA Readback Accuracy Voltage Current Response time Transient recovery time (50%~100% rated load) Protective function ≤0.1%±20mV ≤0.1%±10mA ≤1ms OVP 0~31V OCP 0~5.
6.Technical Specification Communication Port USB communication, compatible with SCPI USB Charging Port Dimension 5V/1A USB charging 82mm(Width)×142mm(Height)×226mm(Length) Weight Approx. 1.
7.Appendix 7. Appendix 7.1 Appendix A: Accessories （The accessories subject to final delivery. ） Power cord x 1 User manual EN x 1 User manual DE x 1 Safety Hintsheet x 1 Fuse x 1 USB Cable x 1 7.2 Appendix B: General Care and Cleaning General Care Do not store or leave the instrument where the liquid crystal display could be exposed to direct sunlight for long periods of time. Caution: To avoid any damage to the instrument, do not exposed it to any sprays, liquids, or solvents.
