Instructions

ManualsBrandsVOLTCRAFT ManualsLaboratory EquipmentVOLTCRAFT DSO-6084F Digital 80 MHz 4-channel 1 GS/s 40000 KP 8 Bit Digital storage (DSO), Function generator

Quick Guide

Front Panel

5 4

1. Display area

2. Select the right menu item

3. Control (button and knob) area

4. Probe Compensation: Measurement signal ( ≈ 3.3V/1kHz) output.

5. Input connectors of four channels

6. Remove the left and right menu

7. Select the bottom menu item

8. Copy button: You can save the waveform by just pressing this button in any user

interface.

9. USB Host port: It is used to transfer data when external USB equipment connects to

the oscilloscope regarded as "host device". For example: Saving the waveform to

USB flash disk needs to use this port.

10. Power on/off

Summary of content (7 pages)

PAGE 1
Quick Guide Quick Guide Front Panel 10 9 8 3 2 1 6 7 1. 2. 3. 4. 5. 6. 7. 8. 5 4 Display area Select the right menu item Control (button and knob) area Probe Compensation: Measurement signal ( ≈ 3.3V/1kHz) output. Input connectors of four channels Remove the left and right menu Select the bottom menu item Copy button: You can save the waveform by just pressing this button in any user interface. 9.
PAGE 2
Quick Guide Rear Panel 1 2 10 9 3 4 5 8 7 6 1. 2. 3. 4. 5. 6. 7. Handle Air vents AC power input jack Fuse Foot stool: Adjust the tilt angle of the oscilloscope. LAN port: the network port which can be used to connect with PC. USB Device port: It is used to transfer data when external USB equipment connects to the oscilloscope regarded as "slave device". For example: to use this port when connect PC to the oscilloscope by USB. 8.
PAGE 3
Quick Guide Control Area 8 1 7 6 2 3 5 4 1. Function button area: Total 11 buttons 2. Waveform generator controls (optional) or DAQ: This function is not available. P/F: Pass/Fail W.REC: Waveform Record 3. Trigger control area with 2 buttons and 1 knob. The Trigger Level knob is to adjust trigger voltage. Other 2 buttons refer to trigger system setting. 4. Horizontal control area with 1 button and 2 knobs.
PAGE 4
Quick Guide the menu on the left and right. User Interface Introduction 1 2 3 56 7 4 5 8 9 10 11 12 13 30 14 29 15 28 27 16 17 18 19 20 26 25 24 23 22 21 1. 2. Waveform Display Area. Run/Stop (touchable) 3. The state of trigger, including: Auto: Automatic mode and acquire waveform without triggering. Trig: Trigger detected and acquire waveform. Ready: Pre-triggered data captured and ready for a trigger. Scan: Capture and display the waveform continuously. Stop: Data acquisition stopped.
PAGE 5
Quick Guide 12. The waveform of CH1. 13. The pointer shows the trigger level position of the source in trigger menu. 14. The two blue dotted lines indicate the horizontal position of cursor measurement. 15. The waveform of CH2. 16. The waveform of CH3. 17. The waveform of CH4. 18. The frequency of the trigger signal. 19. The icon shows the selected trigger type, e.g. represents triggering on the rising edge for an Edge trigger. The reading shows the trigger level value of the corresponding channel. 20.
PAGE 6
Technical Specifications Technical Specifications Oscilloscope Performance Characteristics Vertical Resolution (A/D) Bandwidth Rise time Instruction 8 bits DSO-6084 80 MHz DSO-6104 100 MHz DSO-6204 200 MHz DSO-6084 ≤ 4.375 ns DSO-6104 ≤ 3.5 ns DSO-6204 ≤ 1.
PAGE 7
Technical Specifications Period, Frequency, Mean, PK-PK, RMS, Max, Min, Top, Base, Amplitude, Automatic measurement Overshoot, Preshoot, Rise Time, Fall Time, +Pulse Width, -Pulse Width, +Duty Cycle, -Duty Cycle, Delay A→B , Delay A→B , Cycle RMS, Cursor RMS, Screen Duty, Phase, +Pulse Count, -Pulse Count, Rise Edge Count, Fall Edge Count, Area, and Cycle Area.