Instructions
Table Of Contents
- 1.General Safety Requirements
- 2.Safety Terms and Symbols
- 3.Junior User Guidebook
- Introduction to the Structure of the Oscilloscope
- User Interface Introduction
- How to Implement the General Inspection
- How to Implement the Function Inspection
- How to Implement the Probe Compensation
- How to Set the Probe Attenuation Coefficient
- How to Use the Probe Safely
- How to Implement Self-calibration
- Introduction to the Vertical System
- Introduction to the Horizontal System
- Introduction to the Trigger System
- Touchscreen Controls
- Magnifier Function
- 4.Advanced User Guidebook
- How to Set the Vertical System
- Use Mathematical Manipulation Function
- Use Vertical Position and Scale Knobs
- How to Set the Horizontal System
- How to Set the Trigger/Decoding System
- How to Operate the Function Menu
- How to Implement Sampling Setup
- How to Set the Display System
- How to Save and Recall a Waveform
- How to Record/Playback Waveforms
- How to Clone and Recall a waveform
- How to Implement the Auxiliary System Function Set
- How to Update your Instrument Firmware
- How to Measure Automatically
- How to Measure with Cursors
- How to Use Autoscale
- How to Use Built-in Help
- How to Use Executive Buttons
- How to Print the Screen Image
- 5.Use the Arbitrary Function Generator (Optional)
- 6.Use the Multimeter (Optional)
- 7.Communication with PC
- 8.Demonstration
- 9.Troubleshooting
- 10.Technical Specifications
- 11.Appendix
6.Use the Multimeter (Optional)
108
Push the Utility button, select Function in the bottom menu, select DAQ in the left menu.
The description of DAQ Menu is shown as the follows:
To record the current/voltage measurements in the multimeter, do the following:
1. Push DMM button on the front panel to enter the multimeter function. Select Current
or Voltage in the bottom menu.
If you want to enter the relative mode, select Configure in the bottom menu, select
Relative in the right menu.
2. Push the Utility button, select Function in the bottom menu, select DAQ in the left
menu.
3. Select Storage in the bottom menu, select Internal or External in the right menu. If
you select External, insert the USB memory device into the front-panel USB port on
your instrument.
4. Select Set in the bottom menu, select Enable in the right menu as ON.
5. Select Interval in the right menu, turn the M knob to set it.
6. Select Duration in the right menu, push it to switch between the time unit, turn the M
knob to set the corresponding value.
7. Select STRT in the bottom menu.
8. When external storage is selected: The instructions will be shown on the screen. The
record file will be named as "Multimeter_Recorder.csv". If a file with the same name
already exists in the USB memory device, it will be overwritten. (If you want to keep
the existing file, back up it to other location in advance.) Select STRT in the bottom
menu to start recording.
9. When the record time gets to the defined duration, the recording will be ended. If you
want to end recording prematurely, select STOP in the bottom menu.
Function Menu
Setting
Description
Set
Interval
Set the record interval (0.5s - 10s, step by 0.5s)
Duration
"d h m s" represents day, hour, minute, second.
E.g. "1 02:50:30" represents a day and 2 hours, 50
minutes and 30 seconds.
Press Duration to switch between the time unit, turn
the M knob to set the value. Max duration: 3 days for
internal storage, 10 days for external storage.
Enable
Turn on or off the recorder.
STRT
STOP
Start or stop recording.
Storage
Internal
External
Save to internal storage or USB memory device.
Export
When internal storage is selected, you can export the internal
record file to a USB memory device.