Instructions

ManualsBrandsVOLTCRAFT ManualsLaboratory EquipmentVOLTCRAFT DSO-6202F Digital 200 MHz 2-channel 1 GS/s 40000 KP 14 Bit Digital storage (DSO), Function generator

Quick Guide

Front Panel

1. Display area

2. Control (button and knob) area

3. Probe Compensation: Measurement signal (5V/1kHz) output.

4. EXT Trigger Input

5. Signal Input Channel

6. Copy button: You can save the waveform by just pressing this button in any user

interface.

7. USB Host port: It is used to transfer data when external USB equipment connects to

the oscilloscope regarded as "host device". For example: Saving the waveform to USB

flash disk needs to use this port.

8. Power on/off

Backlight of this button:

Red light: The oscilloscope is turned off (connects with AC Power);

Green light: The oscilloscope is turned on.

Summary of content (7 pages)

PAGE 1
Quick Guide Quick Guide Front Panel 1 8 7 2 6 5 1. 2. 3. 4. 5. 6. 4 3 Display area Control (button and knob) area Probe Compensation: Measurement signal (5V/1kHz) output. EXT Trigger Input Signal Input Channel Copy button: You can save the waveform by just pressing this button in any user interface. 7. USB Host port: It is used to transfer data when external USB equipment connects to the oscilloscope regarded as "host device".
PAGE 2
Quick Guide Rear Panel 1 2 11 3 10 4 5 6 9 8 7 1. 2. 3. 4. 5. 6. 7. 8. Handle Air vents Input terminals of optional multimeter AC power input jack Fuse Foot stool: Adjust the tilt angle of the oscilloscope. LAN port: the network port which can be used to connect with PC. USB Device port: It is used to transfer data when external USB equipment connects to the oscilloscope regarded as "slave device". For example: to use this port when connect PC to the oscilloscope by USB. 9.
PAGE 3
Quick Guide Control Area 11 1 10 9 2 3 8 7 6 5 4 1. Function button area: Total 11 buttons 2. Waveform generator controls (optional) or DAQ: Multimeter (optional) recorder P/F: Pass/Fail W.REC: Waveform Record 3. Trigger control area with 2 buttons and 1 knob. The Trigger Level knob is to adjust trigger voltage. Other 2 buttons refer to trigger system setting. 4. Horizontal control area with 1 button and 2 knobs.
PAGE 4
Quick Guide you can turn the M knob to select the menu or set the value. You can push it to close the menu on the left and right. User Interface Introduction 1 2 3 4 5 6 7 86 9 10 11 12 13 28 14 15 16 17 27 26 18 19 20 25 24 23 22 21 1. Waveform Display Area. 2. Run/Stop (touchable) 3. The state of trigger, including: Auto: Automatic mode and acquire waveform without triggering. Trig: Trigger detected and acquire waveform. Ready: Pre-triggered data captured and ready for a trigger.
PAGE 5
Quick Guide 11. It shows setting time. 12. It indicates that there is a USB disk connecting with the oscilloscope. 13. Multimeter window. 14. The pointer shows the trigger level position. 15. The waveform of CH1. 16. The two blue dotted lines indicate the horizontal position of cursor measurement. 17. The waveform of CH2. 18. It indicates the measured type and value of the corresponding channel.
PAGE 6
Technical Specifications Technical Specifications Oscilloscope Vertical Resolution (A/D) 8 bits mode 12 bits mode 14 bits mode Bandwidth Rise Time ≤ 1.75 ns ≤ 2.33 ns ≤ 17.
PAGE 7
Technical Specifications Waveform Generator (Optional) Max Frequency Output 25 MHz (Sample 125 MS/s) or 50 MHz (Sample 250 MS/s) (optional) Channel 2 Vertical Resolution 14 bits Amplitude Range 2 mVpp - 6 Vpp Waveform length 8K Standard Waveforms Sine, Square, Ramp, and Pulse Multimeter (Optional) Full scale reading 3¾ digits (Max 4000 – count) Diode 0 V - 1.5 V Input impedance 10 MΩ On/Off measurement <50(±30)Ω beeping Capacitance 51.