Voltec Power Inverter Owner’s Manual 100W (Model #: 10-00474) 1000W (Model #: 10-00480) 400W (Model #: 10-00477) 1500W (Model #: 10-00481) 750W (Model #: 10-00479) 2000W (Model #: 10-00482) 3000W (Model #: 10-00483) Thank you for purchasing this VOLTEC product. All VOLTEC products are produced to the highest quality. To reduce the risk of injury, please read this instruction manual and retain for future reference. Should you have any questions or need any support, please contact us at www.
CONTENTS 1. 2. 3. 4. 5. 6. Introduction............................................................ 2 Safety Information ................................................. 3 Features................................................................... 5 Connecting/Operating the inverter ...................... 8 Troubleshooting ................................................... 10 Specifications ........................................................ 14 1.
• Do not connect the unit to any utility power distribution systems or branch circuits. • Do not use the inverter in temperatures over 104(40℃) or under 32(0℃). Caution Do not use the unit on the following items: Small nickel-cadmium battery-operated appliances such as flashlights, razors and nightlights Battery chargers for battery packs used in hand power tool that have a warning label indicating dangerous voltages are present at the battery terminals.
Wiring 10 DC Cable with Clips—Connect the red clip to the positive terminal of the battery, and the black to the negative. 1. AC Outlets— receptacles for 120V AC products with a total continuous power equal to the wattage (W) of your inverter. 2. Power Button— Connect the inverter to the DC power and press down the button power switch, the AC power is available. 3. Port for Remote Control— Connect the remote control switch and press down the switch, the remote control function acts. 4.
Please follow the following to connect your inverter: 1) Attach the ring type connector marked with red to the red (+) DC terminal and the ring connector marked with black to the black (-) DC terminal on the inerter. Caution! Reversing the polarity will damage to the inverter and void the warranty. 2) Tighten the nut on each DC terminal by hand until it is snug. Do not over-tighten. 3) Attach the black (-) clip to the black (-) battery terminal. 4) Attach the red (+) clip to the red (+) battery terminal.
5. Troubleshooting a) Battery Operating Time Operating time will vary depending on the charge level of the battery, its capacity and the power level drawn by the particular AC load.
Some stereo systems and AM-FM radios have inadequate internal power supply filtering and “buzz” slightly when powered by the inverter. Generally, the only solution is an audio product with a higher quality filter. 2) Television interference The inverter is shielded to minimize its interference with TV signals. However, with weak TV signals interference may be visible in the form of lines scrolling across the screen.
Inverter runs small Low voltage battery Charge the battery loads but not large ones. Disconnect the inverter and Water entered the unit Water entered wipe immediately with a dry cloth, or permanent damage can occur. Low voltage shutdown or Allow unit to cool. Improve air thermal Alarm is sounding shutdown has circulation around unit. Locate occurred. unit to a cooler environment. Reduce load if continuous operation is required.
Model 1000W 1500W 2000W 3000W AC output voltage 125V AC (104V) 125V AC (104V) 125V AC (104V) 125V AC (104V) Continuous output power AC 1000W 1500W 2000W 3000W Maximum AC output surge power 2000W 3000W 4000W 6000W AC output frequency(nominal) 59~61Hz 59~61Hz 59~61Hz 59~61Hz AC waveform Modified sine wave Modified sine wave Modified sine wave Modified sine wave output b) USB Power Output DC output voltage 5V DC c) DC Power Specifications Model 200W DC input voltage 11.0~15.
Maximum AC output 1000W power Maximum AC output 2000W surge power 1500W 2000W 3000W 3000W 4000W 6000W AC output frequency 59~61Hz (nominal) 59~61Hz 59~61Hz 59~61Hz AC output waveform modified sine wave modified sine wave modified sine wave 5V DC 5V DC 12.8~13.2V DC 12.8~13.2V DC modified sine wave 5V DC DC output voltage 5V DC range 12.8~13.2V DC input voltage 12.8~13.2V DC DC range Battery drain with no 0.6A (at a 0.
