Installation instructions, accessories Volvo Car Corporation Göteborg, Sweden S60/V70 (00-)/V70XC (01-)/S80/XC90 Section Group 8 89 Weight (Kg/Pounds) Year Month 2002 06 Tow bar wiring, 7-pin M3702107 © Volvo Car Corporation, 2002 Printed in Sweden 8698534
A0000162 A0000161 R8802817 M3702108 2002 06 8698534
1 2 M3702248 3 M3702109 4 D3701464 5A M8902146 5B M3702110 6A M3702158 6B R8903037 R8903038 2002 06 8698534
7A 7B M8901859 8 M8503264 9 M8301410 10A D8502339 10B R8902382 11A R8902766 11B D3100060 R3100130 2002 06 8698534
12A 12B M3100077 D3100058 13 12C R3100141 14 M3702159 15 M3100112 16 M3100086 17 D3100059 R8902823 2002 06 8698534
18A 18B R8903022 19 R8903087 20A R3100168 20B R3100169 21 R3903744 22 R3903738 23 R8504201 R8504123 2002 06 8698534
24A 24B R8504313 R8504315 25A 24C R8504316 25B D3701643 25C M3702111 R3702888 30 A3701406 2002 06 8698534
English S60 / V70 (00-) / S80 / XC90 INTRODUCTION The collision sensor control module is located on the transmission tunnel in the centre console, in front of the parking brake. • NOTE! Read through the entire text before carrying out any work. • The front page gives the date of this edition and the edition it replaces • The second page shows the tools needed for the installation and the contents of the installation kit • The illustrations display the procedure in order of operation.
Installing the connector for fixed tow bars 4 Applies to the S60 Cargo compartment preparations 7 Illustration A – Install the trailer connector (1). Use the three screws (2) and the nuts (3). Tighten – Fold back the carpet – Remove the clips at the bottom edge of the right and left folding panels (press the centre of the clips until there is an audible click) – Leave the bracket hanging down as illustrated – Secure the cable harness at the tow hitch member on each side of the tow hitch.
Applies to the XC90 12 Illustration A Illustration A applies to the S60, V70 (00-) and V70XC (01-) – Remove the cover plug from the hole in the bodywork (battery drainage is not affected). See the illustration. Applies to cars with two rows of seats – Fold up the centre rear floor hatch (1) – If the floor hatch is equipped with a carrier bag holder, it is secured by a strap on each of the shorter sides of the storage box.
15 Applies to the V70 (00-) and V70XC (01-) 20 – Route the cable harness from the tow bar connector through the hole in the floor Illustration A – Route the cable harness from the tow bar socket through the hole in the floor. It may be necessary to remove the spare wheel which partially obstructs the hole in the floor – Adjust the position of the rubber seal (2) so that there is not too much slack in the cable under the car – Install the rubber seal in the hole – Route the cable as illustrated.
22 – Remove the rear headlining covers and the screws underneath the covers – Carefully pry off the panel at the rear edge using a plastic weatherstrip tool – Pull the rear edge of the panel downwards until the four clips on the top have released 23 Illustration A applies to the S60 and the S80 Illustration B applies to the V70 (00-) and V70XC (01-) Illustration C applies to the XC90 Install the correct fuse / relay depending on the model (year) and desired function – If the car has lighting in the pane
Finishing work 26 Applies to the XC90 Reinstall: – the left-hand side panel using the screws and cover. Tighten the screws in the load securing eyelets. Tighten to 24 Nm (18 lbf.ft.) – the covers for the load securing eyelets – The D-post panel with the connector – the rear roof lighting connector (if applicable) – the rear headlining – C-post panel. 27 – Reinstall the protective cover and the bracket for the battery. (see point 11).