Installation & Assembly

ManualsBrandsVONN Lighting ManualsCeiling LightsGenoa 8 - Light Unique LED Chandelier

INSTALLATION GUIDE

VONN LIGHTING MODEL#

VAC3118

D E

LED INFO & WARNINGS

Please read and understand the entire manual

before attempting to assemble, operate, or install

the product.

VONN highly recommends to use a qualiﬁed,

licensed electrician to install the ﬁxture.

All parts must be used as indicated in these

instructions. Do not substitute any parts, leave

parts out, or use any parts that are worn or broken.

Inspect the LED ﬁxture prior to installation to make

sure that it has not been damaged during shipping.

Please handle the LED light with care when

unpacking. Do not apply pressure to the LED’s, do

not open any factory sealed compartments, and do

not touch the LEDs with your hands.

Shut “OFF” the electricity at main fuse box.

Do not remove or replace VONN manufactured

parts that is provided with the ﬁxture.

Place the wall switch in the “OFF” position of the

room you are installing the ﬁxture.

Make sure that you have all necessary parts by

checking the parts list. If any part is missing or

damaged please contact VONN LIGHITNG

CUSTOMER SERVICE at 888-604-8666 for

a replacement.

VONN recommends to install the ﬁxture on

its own independent circuit. Do not install the

ﬁxture on the same circuit with the other

appliances, or HVAC systems.

DO NOT CUT WIRES attached to the ﬁxture under

any circumstance. Cutting wires will VOID your

warranty. Excess cable should be neatly looped and

tucked into the canopy.

VONN recommends ELV (Electric Low Voltage)

type dimmers for this ﬁxture.

TOOLS YOU MAY NEED

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

www.vonn.com

PARTS LIST

Mounting Bracket x 1

Wire Connectors x 3

Ground Screw x 1

Canopy Screws x 2

Glass Sade x 8

Outlet Screws x 3

CIRCUIT BOX

OFF

Summary of content (10 pages)

PAGE 1
INSTALLATION GUIDE VONN LIGHTING MODEL# VAC3118 TOOLS YOU MAY NEED GOGGLES B F C D RUBBER GLOVES PHILLIPS SCREW DRIVER DRILL LADDER CIRCUIT BOX PARTS LIST A TAPE MEASURE E A. Mounting Bracket x 1 B. Outlet Screws x 3 C. Wire Connectors x 3 D. Ground Screw x 1 E. Canopy Screws x 2 F. Glass Sade x 8 OFF ON OFF LED LED INFO INFO & & WARNINGS WARNINGS Please read and understand the entire manual before attempting to assemble, operate, or install the product.
PAGE 2
Fixture Diagram Ceiling Outlet Box Wire C Connector Mounting A Bracket Ground D Screw Outlet B Screw Canopy E Screw Locking Pin Cable E Glass Shade www.vonn.
PAGE 3
Instructions Step 1. Adjust Height Locking Pin Cable The length of the cable is adjustable. To determine the proper length of the fixture, hold the fixture canopy up against the outlet box in the ceiling to adjust the cable. Depress locking pin on the canopy, hold pin in place, and pull down or push up on the cable. Repeat step for each cable. Installer Tip (1): It is recommended that two installers are required to adjust the height of the fixture.
PAGE 4
Step 2. Install Mounting Bracket Mounting A Bracket B Outlet Screw Step 3. Connect Wires Ceiling Mounting A Bracket Black (Line Wire) C Wire Connector Bare Copper (Ground Wire) Supply Wires: Connect Black (Line Wire) from fixture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from fixture to White (Neutral Wire) from outlet box.
PAGE 5
Step 4. Mount Fixture Mounting A Bracket Canopy E Screw Glass Secure mounting bracket (A) with outlet screws (B). H Shade Step 5. Turn Power ON Turn electricity “ON” at main fuse box. Place the recommended ELV type dimmer switch in the “ON” position to test the fixture. Circuit Box ON ON OFF www.vonn.
PAGE 6
GUIDE D’INSTALLATION : MODÈLE D’ÉCLAIRAGE VONN Nº VAC3118 OUTILS DONT VOUS POURRIEZ AVOIR BESOIN LUNETTES DE PROTECTION B F C D GANTS EN C AOUTCHOUC TOURNEVIS CRUCIFORME PERCEUSE ÉCHELLE PANNEAU ÉLECTRIQUE LISTE DES PIÈCES A MÈTRE RUBAN E A. Support de montage x 1 B. Vis de boitier de dérivation x 3 C. Connecteurs fils électriques x 3 D. Vis de mise à la terre x 1 E. Vis de canopée x 2 F.
PAGE 7
Schéma de montage du luminaire Boitier de dérivation Plafond Connecteurs fils C électriques A Support de montage Vis de mise D à la terre B Vis de boitier de dérivation Vis de E canopée Broche de verrouillage Câble F Abat-jour en verre www.vonn.
PAGE 8
Instructions Étape 1. Ajuster la hauteur Broche de verrouillage Câble La longueur du câble est réglable. Pour déterminer la longueur appropriée du luminaire, maintenez la canopée du luminaire contre le boîtier de dérivation au plafond pour ajuster le câble. Appuyez sur la broche de verrouillage sur la canopée, maintenez la broche en place et tirez vers le bas ou poussez le câble. Répétez l'étape pour chaque câble.
PAGE 9
Étape 2. Installer le support de montage Support de A montage Vis de boitier B de dérivation Étape 3. Connecter les fils Plafond A Support de montage Noir (Fil de phase)) Connecteurs fils C électriques Câbles d’alimentation : Cuivre nu (Fil de mise à la terre) Connectez le noir (Fil de phase) du luminaire au noir (fil à chaud) du boîtier de dérivation. Connectez le blanc (fil neutre) du luminaire au blanc (fil neutre) du boîtier de dérivation.
PAGE 10
Étape 4. Montage du luminaire A Support de montage Vis de E canopée Fixez la canopée au support de montage (A) à l’aide des vis de canopée (E). Abat-jour H en verre Étape 5. Rétablir le courant Armez le fusible (position « ON ») à la boîte à fusibles principale Placez le variateur de lumière de type BT recommandé sur « ON » (Allumé) pour tester le luminaire. Boitier coupe-circuit ALLUMÉ ALLUMÉ ÉTEINT www.vonn.