Installation Guide

ManualsBrandsVonn Lighting ManualsFlush Mount LightingExpression 11-in Black Modern/Contemporary LED Semi-Flush Mount Light ENERGY STAR

Installation Guide

VONN Lighting

Model: VECF48003

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

Tools You May Need

Make sure that you have all necessary parts by checking the parts list. If

any part is missing or damaged, please contact VONN Lighting

Customer Service at 888-604-8666 for a replacement.

Please read and comprehend the entire manual before attempting to

assemble, operate, or install the product.

Optional plug-in or hard wired installation.

DO NOT CUT WIRES attached to the fixture under any circumstance.

Cutting wires will VOID your warranty. Excess cable should be neatly

looped and tucked into the canopy.

LED INFO & WARNINGS

•

All parts must be used as indicated in these instructions. Do not substitute

any parts, leave parts out, or use any parts that are worn or broken.

•

Inspect the LED fixture prior to installation to make sure that it has not

been damaged during shipping.

•

Please handle the LED light with care when unpacking. Do not apply

pressure to the LEDʼs, do not open any factory sealed compartments, and

do not touch the LEDs with your hands.

•

Do not remove or replace VONN manufactured driver that is provided

with the fixture.

Parts List

Ceiling Peg x 8

Plastic Anchors x 12

Anchor Screws x 12

Mounting Bracket

Canopy Screw

Hex Wrench

Ceiling Peg Screws x 8

Summary of content (11 pages)

PAGE 1
Installation Guide LED INFO & WARNINGS • Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. • Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact VONN Lighting Customer Service at 888-604-8666 for a replacement. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
PAGE 2
Fixture Diagram - Plug In C Plastic Anchor B Ceiling Peg Screw DIMMER OFF D Anchor Screw ON A Ceiling Peg C Plastic E Mounting Bracket Anchor D Anchor Screw F Canopy Screw © VONN Lighting,2018
PAGE 3
Step 1. Install Canopy E Mounting Remove mounting bracket (E) from ﬁxture. Raise mounting bracket (E) to wall and mark location for plastic anchors (C). Drill hole for plastic anchors (C) and insert in wall. Bracket E Mounting Bracket Secure mounting bracket (E) with anchor screws (D). C Plastic Anchor D Anchor Screw E Mounting Bracket Attach canopy to mounting bracket (E). Secure canopy with canopy screws (F).
PAGE 4
Step 2. Install Wire Expression 1. Plastic C Anchor Drill hole for plastic anchors (C). Insert plastic anchors (C) into hole. Secure ceiling peg screw (B) with anchor screw (D). Ceiling B Peg Screw D Anchor Screw Ceiling 2. B Peg Attach ceiling peg (A) on ceiling peg screw (B) and tighten. Screw A Ceiling Peg 3. G Hex Wrench Secure ceiling peg (A) with set screw. Tighten with hex wrench (G).
PAGE 5
Step 3.
PAGE 6
Installation Guide LED INFO & WARNINGS • Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. • Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact VONN Lighting Customer Service at 888-604-8666 for a replacement. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
PAGE 7
Fixture Diagram - Hard Wired WALL INSTALLATION C Plastic Anchor B Ceiling Peg Screw D Anchor Screw A Ceiling Peg CEILING INSTALLATION C Plastic Anchor G Ground Screw E Outlet Screw C Plastic Anchor I Mounting Bracket B Ceiling Peg Screw D Anchor Screw J Wire Clip F Wire Connector D Anchor F Canopy Screw Screw A Ceiling Peg © VONN Lighting,2018
PAGE 8
Step 1. Install Mounting Bracket I Mounting Bracket Remove mounting bracket (I) from ﬁxture. Raise mounting bracket (I) to wall or ceiling and mark location for plastic anchors (C). Drill hole for plastic anchors (C). Insert anchors. C Plastic Anchor E Outlet Screw I Mounting Bracket D Anchor Screw Attach mounting bracket (I) to outlet box with outlet screws (E). Screw anchor screws (D) into plastic anchors (C) to secure canopy.
PAGE 9
Step 2. Connect Wires Remove line wire (black) and neutral wire (white) from wire clip (J) for hard wire installation. L N J Wire Clip G Ground Screw Supply Wires: Connect Black (Line Wire) from ﬁxture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from ﬁxture to White (Neutral Wire) from outlet box. Ground Wires: Connect Bare Copper (Ground Wire) from ﬁxture to Green or Bare Copper (Ground Wire) from outlet box.
PAGE 10
Step 3. Secure Canopy Canopy Attach canopy to mounting bracket (I). Secure with canopy screws (F). I Mounting Bracket F Canopy Screw Step 4. Install Wire Expression 1. Plastic C Anchor Drill hole for plastic anchors (C). Insert plastic anchors (C) into hole. Secure ceiling peg screw (B) with anchor screw (D). Ceiling B Peg Screw D Anchor Screw Ceiling 2. B Peg Attach ceiling peg (A) on ceiling peg screw (B) and tighten. Screw A Ceiling Peg 3.
PAGE 11
Step 5. Turn Power ON Turn electricity “ON” at main fuse box. Place the single pole switch in the “ON” position to test the ﬁxture.