Installation Sheet

ManualsBrandsVonn ManualsChandeliersCapella Collection 30" LED Chandelier, Adjustable Hanging Light, Modern Flower-Petal Chandelier Lighting in Black

Installation Guide

VONN Lighting

Model: VMC32420

Tools You May Need

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

Parts List

Circuit Box

Canopy Cover

Anchor Screws x 4

Outlet Screws x 3

Wire Connectors x 3

Ground Screw x 1

Canopy Screws x 3

Plastic Anchors x 4

Make sure that you have all necessary parts by checking the parts list. If

any part is missing or damaged, please contact VONN Lighting

Customer Service at 888-604-8666 for a replacement.

Please read and comprehend the entire manual before attempting to

assemble, operate, or install the product.

VONN highly recommends to use a qualified, licensed electrician to install

the fixture.

VONN recommends to install the fixture on its own independent circuit.

Do not install the fixture on the same circuit with other appliances, or

HVAC systems.

DO NOT CUT WIRES attached to the fixture under any circumstance.

Cutting wires will VOID your warranty. Excess cable should be neatly

looped and tucked into the canopy.

LED INFO & WARNINGS

•

All parts must be used as indicated in these instructions. Do not substitute

any parts, leave parts out, or use any parts that are worn or broken.

•

Inspect the LED fixture prior to installation to make sure that it has not

been damaged during shipping.

•

Please handle the LED light with care when unpacking. Do not apply

pressure to the LEDʼs, do not open any factory sealed compartments, and

do not touch the LEDs with your hands.

•

Place the wall switch in the “OFF” position of the room you are installing

the fixture.

•

Shut “OFF” the electricity at main fuse box.

•

Please remove the canopy from the box prior to the fixture body. Failure

to do so can potentially lead to cables getting tangled.

•

VONN recommends ELV (Electric Low Voltage) type dimmers for this

fixture.

•

Do not remove or replace VONN manufactured driver that is provided

with the fixture.

Summary of content (6 pages)

PAGE 1
Installation Guide LED INFO & WARNINGS • Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. • Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact VONN Lighting Customer Service at 888-604-8666 for a replacement. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
PAGE 2
Fixture Diagram Outlet Box G Canopy cover screws A Canopy Cover E Wire Connector Ceiling B Plastic Anchor F Ground Screw C Anchor Screw D Outlet Screw Canopy Locking Pin Cable © VONN Lighting,2018
PAGE 3
Step 1. Adjust Height Locking Pin Cable The length of the cable is adjustable. To determine the proper length of the ﬁxture, hold the ﬁxture canopy up against the outlet box in the ceiling to adjust the cable. Depress locking pin on the canopy, hold pin in place, and pull down or push up on the cable. Repeat step for each cable. Installer Tip (1): It is recommended that two installers are required to adjust the height of the ﬁxture.
PAGE 4
Step 2. Install Canopy Cover Outlet Box Ceiling A Canopy Cover Raise canopy cover (A) to the ceiling. Mark location for the plastic anchors (B). Drill holes for plastic anchors (B). Insert plastic anchors (B) into hole. Outlet Box B Plastic Anchor Ceiling A Canopy Cover D Outlet Screw C Anchor Screw Attach canopy cover (A) to outlet box with outlet screws (D). Screw anchor screws (C) into plastic anchors (B) to secure canopy cover (A).
PAGE 5
Step 3. Connect Wires A Canopy Cover F Ground Screw Black (Line Wire) White (Neutral Wire) Ceiling E Wire Connector Bare Copper (Ground Wire) Supply Wires: Connect Black (Line Wire) from ﬁxture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from ﬁxture to White (Neutral Wire) from outlet box. Ground Wires: Connect Bare Copper (Ground Wire) from ﬁxture to Green or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (E).
PAGE 6
Step 4. Mount Fixture Outlet Box G Canopy Screws A Canopy Cover Canopy Attach canopy to canopy cover (A). Twist canopy to lock ﬁxture in place. Secure canopy with canopy screws (G). Step 5. Turn Power ON Turn electricity “ON” at main fuse box. Place the recommended ELV type dimmer switch in the “ON” position to test the ﬁxture.