VOOK VOOK HD-SDI Digital video recorders VDT2708XD-M ; VDT2716XD-M
VOOK
8/16-CH DVR Quick Start Guide VOOK 1. Hardware installations 1.1 Install Hard Drive Notice: 1.This series support eight SATA hard drives. Please use the hard drive the manufacturers recommend specially for security and safe field. 2. Please calculate HDD capacity according to the recording setting. Step1: Unscrew and Open the top cover Step2: Connect the power and data cables. Place the HDD onto the bottom case as the following picture.
8/16-CH DVR Quick Start Guide VOOK 2.1 Rear view for 8-ch DVR 1 2 3 4 5 6 7 8 HD SDI video signal inputs. Alarm Inputs for connecting sensors Connect to high-definition display device VGA output, connect to monitor Network port Connect USB mouse or connect external USB devices Grounding Connect to keyboard. A is TX+, B is TX-. 9 Connect to speed dome. Y is TX+, Z is TX- 10 CVBS output 11 Audio output, connect to the sound box 12 Talk. Connect to microphone 13 Relay Output.
8/16-CH DVR Quick Start Guide VOOK 3. Startup &Shutdown 3.1 Startup Step1: Connect to cameras and monitor. Step2: Connect with the source power; Step3: The device will boot and the power indicator will display blue. Step4: A WIZZARD window will be pop-up. 3.2 Shutdown You can shut down the device by using IR remote controller and mouse. By IR remote controller: Step1: Press Power button. This will bring up a shutdown window. The unit will shut down by clicking “OK” button.
8/16-CH DVR Quick Start Guide VOOK It supports digits, alphabets and symbols as inputs. Click Shift button to input Capital letters and symbols; click Shift button again to return. Click „Next‟ button to bring up a network setup window. The default HTTP port is 80. The default server port is 6036. You can check „Obtain an IP address automatically‟ to acquire network information or input IP address, subnet mask, gateway, preferred/alternate DNS server manually.
8/16-CH DVR Quick Start Guide VOOK 5. Login After you exit the wizard setup, you can login to the DVR. Notice: This DVR can only display options on either VGA/HDMI monitor or BNC monitor at a given point of time, if there is live image display without menu options,please check if there is display on other device/monitor, or long press ESC/Fn key to wait for login dialog box to appear. Long press ESC/Fn key can switch the output between BNC and VGA/HDMI.
/16-CH DVR Quick Start Guide VOOK and sensor alarm respectively. Alarm configuration: Users can set sensor type, alarm trigger and buzzer alarm. Network configuration: Users enable network function, and configure IP address, DDNS, transmission video parameters here. User configuration: Administrator can add, delete users, and change their authorization PTZ configuration: Users can set protocol, baud rate, address, presets and auto cruise track here.
8/16-CH DVR Quick Start Guide VOOK delete the selected schedule; Step 3: You can also double-click the grid to pop up a week schedule window. Select day and then click „Add‟ button to setup the start time and end time. Then select other days and click „Copy‟ button to save the setting to other days. Finally, click „OK‟ button to save week schedule.
8/16-CH DVR Quick Start Guide VOOK detection area. Click icon to test the sensitivity as per the local conditions. icon to save the Once motion is sensed, it displays a figure icon. Click setting. Click icon to exit the current interface Step 5: Enter into MenuSetupAlarmMotionSchedule tab to bring up schedule settings for motion alarm. The setup steps are similar to normal schedule setup. You can refer to 7.2 Schedule Recording for details.
8/16-CH DVR Quick Start Guide VOOK schedule setup. You can refer to 7.2 Schedule Recording for details. Note: The timelines of the two schedules must match, otherwise you cannot get the record in some time. 8. Playback This unit supports four kinds of playback 8.1 Live Playback Click Play button on the main menu bar to playback the record. User can do concrete operation by clicking the buttons on screen. 8.2 Playback by Time Search Step 1: Enter into MenuSearchTime Search tab.
8/16-CH DVR Quick Start Guide VOOK Step 2: Select date and channels on the right hand side and press “Search” button. A date with highlighted borderline indicates presence of data. Step 3: Set the start time by clicking a particular grid or by entering the specific value in the start time field. Step 4: Select the channel display mode and click Use the playback toolbar to control the playback. 8.3 button to play record. Playback by Event Search Step 1: Enter into MenuSearchEvent Search tab.
8/16-CH DVR Quick Start Guide VOOK Step 3: Press “Search” button to search for a recorded image. Step 4: Once an alarm image has been identified, the user can double click the image to play the recording. You can lock the image by clicking “Lock” button. Click “Save” button to copy the image on the HDD. Click “Save All” to copy all images on the HDD. Note: In order to take images on alarm, the snapshot feature should be activated in “Alarm Handling” for different kind of alarms.
8/16-CH DVR Quick Start Guide VOOK ● Enter into Record Setup to set network video parameters like resolution, frame rate etc. ● Open IE on a computer on the same network. Input the IP address of the DVR in IE address bar and press enter. If HTTP port is not 80, add the port number after IP address. ● IE will download ActiveX component automatically. Enter the username and password in the subsequent window 10.2 Access DVR on WAN 1.
8/16-CH DVR Quick Start Guide VOOK „Apply‟. The DVR will connect to the server and would give a confirmation message. ● If users want to utilize dynamic domain name, please apply for a domain name in a DNS server supported by the DVR or router. Then add to the DVR or router. ● When accessing the remote interface of DVR, user can input WAN IP/domain name to access directly (user can enter into Main menuInformationNetwork interface to check IP address).