SMART CENTRE VIDEO INTERCOM SYSTEM USERS’ MANUAL VOOK INTELLIGENT TECHNOLOGY MANUAL CODE: VHD-M1743MX
Contents INSTALLATION MANUAL Cover Contents 1 Installation Guide 2 Features & Specifications 3 Descriptions for Monitor 4 Descriptions for Doorbell/Camera 5 Wiring Diagrams and Schematics 6-11 Installation 12-13 OPERATION GUIDE Operation Guide 14 System Settings 15-19 Care Instructions 19 1
Installation Guide 2
FEATURES & SPECIFICATIONS Features Dual communication & Call Transfer Door Release Image capture (option without memory, 8 or 64 Pictures memory ) Picture memories with date and time By no answer, automaticly picture memory TV/MUSIC Playing CCTV Surveillance Supports 2 cameras and 8 Monitors Monitor/Intercom/Broadcast System settable (Time/volume/Brightness/Contrast/Color) Hands free surface/flush mounted, 7 inch TFT Screen Technical Specifications: Monitor Display screen 7 inch TFT Re
DESCRIPTIONS OF MONITOR 1. LCD Screen 2. Monitor/Answer Button 3. Intercom Button 4. Door Release 5. Adjustment: Left/Right 6. On/Off Button 7. Image Capture 8. Microphone 9. Speaker 10. Siren 11.
DESCRIPTIONS OF DOORBELL CAMERA 1. 2. 3. 4. 5.
WIRING DIAGRAMS AND SCHEMATICS Cable and Connections for Doorbell/Camera z z z z 1R： 2B： 3Y： 4W： +12V GND VIDEO AUDIO power supply positive for Doorbell/camera power supply ground for Doorbell/camera image signal transmitting line talk and control lines Cable and Connections for Monitor Connection block CN1： 18V,GND：Terminals for Power Supply Input Connection block CN2： 12V,GND,AU1,VD1,UNLOCK1+(SDOOR1): Terminals for Power supply/Ground/Audio/Video/Unlock for the Doorbell/camera1.
Connection block CN4： Standby Block AU3,GND,VD3,GND： Terminals for Expanded Audio/Ground/Expanded Video/Ground Connection block CN5： VD4,VD5,VD6,GND： Terminals for Expanded Video/GND Connection block CN6： +18V,GND,DATA,AU,VD,GND： terminals for Power+/Power Ground/Data/Audio/Video/Video Ground System Schematics 2 Cameras, 2 Latches Multiple Monitors 7
Wiring Diagrams 1 Camera, 1 Latch 1 Monitor 8
Wiring Diagrams 2 Cameras, 2 Latches 1 Monitor 9
Wiring Diagrams 2 Cameras, 2 Monitors, 2 Latches 10
Wiring Diagrams 2 Cameras, 2 Latches Multiple Monitors NOTE: 1.The connectors for “+18V & GND” on the connection block CN1 need to be connected with 18V DC power supply. 2.
INSTALLATION Installation Instructions Please see the relevant wiring diagram for the System you have chosen and ensure you have the correct cable for that systems requirements. 1. Single Monitor Installations: 1.1 Determine both Monitor and Doorbell/Camera operating positions and heights. (Average height 1.5 to 1.6 Metres). 1.2 Run the appropriate cable between the two positions allowing at least 350mm excess at each location. 1.3 Unplug the connection terminal from the back of the monitor (Terminal J5).
2. Single Doorbell/Camera: 2.1 Please take a moment to select the most suitable Doorbell/Camera position. 2.2 Please consider both daytime, night time and likely weather condition impact. Direct sunlight on the camera and direct contact with rain should be avoided. 2.3 Determine Camera Position: Please ensure you run cable through the camera mounting plate. (Average Height 1.5 to 1.6 metres). 2.4 Surface Mount Doorbell/Cameras require fitting of each cameras mounting.
Operation Guide 14
SYSTEM SETTINGS At standby mode, press and hold “Photo Button” for 2 seconds to get into the set-up mode as below.
2. Intercom function In standby mode, a single press of BUTTON 3 from any monitor will call the other monitors. Extension monitors will chime until any monitor answers by pressing button 2. 3. Broadcasting function to other monitors At standby mode, press and hold BUTTON 3 of any monitor to activate the broadcasting function, while held down talk to all other monitors. 4. Call & Unlock function When visitors press the Doorbell/Camera, the visitors image of will show on the Monitor screen.
5. Monitoring function: View Outside from Doorbell/Camera at any time Press and hold “Monitor” (BUTTON 2) on any monitor will view the outside images from the Doorbell/Camera. Green & Red lights will display for Camera 1 or 2 respectively. The monitoring time is preset at 30sec. 6. Brightness/Contrast/Colour In standby mode press BUTTON 2 to display an image, press either adjustment ” ◄►”(button 5) to adjust the Brightness/Contrast/Color for the image.
CHI ME VOL LOW CHI ME VOL HI GH CHI ME VOL MUTE TALK VOL LOW TALK VOL LOW TALK VOL LOW 9. Adjusting Talk Volume In standby mode, press “answer” BUTTON 2 for 6 seconds, the blue screen will display the current talk volume. Keep pressing this button to adjust the talk volume. E.g fig. below: CHI ME VOL HI GH CHI ME VOL HI GH TALK VOL LOW TALK VOL HI GH In this mode, with the current setting flashing, press BUTTON 7 to move adjustment from chime to the talk-setting.
12. Photo Function ( VHD-M1743M8 , VHD-M1743M64 ) When visitor press BUTTON 3, if there is no answer from the Monitor/Monitors after 10 seconds, the photo function will take an image of the visitor and store it for later viewing. The date / time is also stored. Up to 64 images ( VHD-M1743M64 ) can be stored. As new images are stored old images are deleted. 13.
