User Manual

52
to switch programs. Similarly, when ToneLab LE
receives a program change message, its program
will switch automatically. Here’s how you can
specify whether a program change message will
be transmitted from the MIDI OUT jack when you
switch programs on ToneLab LE.
NOTE: Program change numbers not used by
ToneLab LE will be ignored. For details on the
range of program change numbers used by
ToneLab LE, refer to End of this manual.
1. Press the GLOBAL button (4.6).
2. Press the √√
√√
, ®®
®®
buttons (4.3) to make the
name display (3.1) show “PCHG OUT.”
3. Specify whether program change messages
will be transmitted. Use value knob 6 (2.2)
or the ▲, ▼ buttons (4.2) to make the
desired setting.
“OFF”: Program change messages will
not be transmitted.
“On”: Program change messages will be
transmitted.
C ONTROL C HANGE (GLOBAL “CCHG I/O”)
When you operate the EXPRESSION pedal, or
Control switch of the ToneLab LE, control
change messages will be transmitted. This
means that functions for the corresponding con-
trol change numbers on an external MIDI device
can be controlled in realtime.
Similarly, when ToneLab LE receives control
change messages from an external MIDI device,
it will be controlled in the same way as if its own
foot controller were operated.
For a list of the functions that can be controlled
from an external MIDI device, refer to step 4.
Here you can specify whether ToneLab LE will
transmit and receive control change messages.
1. Press the GLOBAL button (4.6).
2. Press the
√√
√√
, ®®
®®
buttons (4.3) to make the
name display (3.1) read “CCHG I/O.”
3. Specify whether all control change mes-
sages will be transmitted or received. Use
value knob 6 (2.2) or the ▲, ▼ buttons (4.2)
to make your choice.
“On” allows transmitting and receiving.
“OFF” disables transmitting and receiving.
NOTE: If this setting is “OFF,” no control change mes-
sages will be transmitted or received even if
you specify individual control change numbers
in step 4.
4. Simultaneously press both √√
√√
, ®®
®®
buttons
(4.3) to access the screen where you can
set control numbers individually. Use the √√
√√
,
®®
®®
buttons to select each controller.
The controllers will be selected in the fol-
lowing order.
5. For each controller, specify whether ToneLab
LE will transmit and receive control change
messages. If you want ToneLab LE to transmit
and receive messages for a controller, specify
the control change number. Select a control-
ler, and use value knob 6 (2.2) or the ▲, ▼
buttons (4.2) to make the desired setting.
“OFF”: Control change messages will not
be transmitted or received.
“CC00”–“CC95”: When you operate a
controller, messages of the specified con-
trol change number 00–95 will be trans-
mitted. Similarly, ToneLab LE will be
controlled when it receives messages of
the same control change number from an
external MIDI device.
6. To return to the screen where you specify
transmit or receive for all control change
messages, press both √√
√√
, ®®
®®
buttons (4.3)
simultaneously.
PARAMETER CHANGE (GLOBAL “SYEX
OUT”
)
When you operate ToneLab LE’s knobs or buttons
to edit the value of a parameter, system exclusive
such as parameter changes are transmitted.
If you want ToneLab LE’s parameters to be
transmitted to an external device, turn the “SYEX
OUT” setting “On.” Normally, you will turn “SYEX
OUT” on when using the Sound Editor.
This setting specifies whether ToneLab LE will
transmit parameter changes.
1. Press the GLOBAL button (4.6).
2. Press the
√√
√√
, ®®
®®
buttons (4.3) to make the
name display (3.1) read “SYEX OUT.”
3. Specify whether parameter change mes-
sages will be transmitted. Use value knob 3
(2.2) or the ▲, ▼ buttons (4.2) to make your
choice.
“EXP PDL” Expression pedal control
“CTRL PDL” Control switch on/off
“PEDAL FX” PEDAL effect on/off
“MOD FX” MODULATION effect on/off
“DELAY FX” DELAY effect on/off
“REVRB FX” REVERB effect on/off
“INSRT FX” External effect on/off
“AMP CTRL”
Amp model on/off (limited to
reception)
“CAB CTRL”
Cabinet model on/off (limited to
reception)