User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
11
Panels
1. Program/loop control section
This section controls the loops functions such as recording
and playback for Loop 1 and Loop 2, and setting the tempo.
a
b
c
g
f
e
d
a. Current loop LEDs
These LEDs indicate the loop that’s selected for control, such
as recording or playback. The status of the STOP pedal and
the REC/PLAY/OVERDUB pedal apply to the selected loop.
To select a loop, press the STOP pedal and the PROGRAM
UP pedal simultaneously. You’ll switch between Loop 1 and
Loop 2 each time you do so.
b. LOOP STATUS LEDs
These LEDs indicate the status of Loop 1 and Loop 2.
) p.28 “Loop status”
c. REC/PLAY/OVERDUB pedal
This pedal initiates recording, playback, overdubbing, or
resampling for the loop that currently selected.
If no phrase has been recorded on the loop that currently
selected, the function will cycle between recording →
playback → overdubbing each time you press the pedal.
If a phrase has been recorded on the loop that currently
selected, the function will cycle between playback →
overdubbing each time you press the pedal.
If the RESAMPLING STATUS LED is blinking, resampling
will start when you press this pedal.
d. RESAMPLING STATUS LED
This LED indicates the resampling status. Use the REC/
PLAY/OVERDUB pedal to start or end resampling.
) p.25 “Resampling”
e. STOP pedal
This pedal stops recording, playback, overdubbing, or
resampling. You’ll also use this pedal to erase a phrase
recorded in a loop.
By holding down this pedal and the PROGRAM UP pedal
simultaneously for approximately two seconds, you can turn
the Pre Effect on/off.
f. PROGRAM UP pedal
Use this pedal to select a program or loop. This pedal is also
used to undo/redo overdubbing.
g. TRIGGER/TAP pedal
This pedal resets playback of the phrase that was recorded in
the loop.