User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
12
VOX Dynamic Looper Owner's manual
You’ll also use this pedal to specify the tempo for the
metronome or for BPM sync-type effects.
This pedal also turns on/off the Loop Quantize function that
adjusts the end of the loop according to the tempo when you
stop recording, allowing you to create loops that are exactly
the right length.
) p.20 “Creating phrases of a precise length
(Loop Quantize)”
2. Pre Effect section
Here you can control the Pre Effect. The Pre Effect will be
applied to the signal from the INPUT jack and the MIC IN
jack.
The effect will be applied to the input that’s selected by the
PRE FX TARGET button.
) p.14 “d. PRE FX TARGET button”
a
b
a. Pre Effect selector
This selects the type of Pre Effect.
b. PRE FX button
This turns the Pre Effect on/off.
The button will light-up red when the effect is on, and it will
blink while you’re editing the effect.
Note: Turning the effect selector will also pedal the Pre
Effect on.
Hint: You can pedal the Pre Effect on/off by holding down
the STOP pedal and the PROGRAM UP pedal
simultaneously for approximately two seconds.
3. Loop Effect section
Here you can control the Loop Effect. The Loop Effect
applies to the phrases recorded in Loop 1 and Loop 2. You
can use this to change the phrase’s pitch (“PITCH” effect), or
mix in a backward playback sound (“REVERSE” effect).
Note: The Loop Effect is available when you’re playing back
a phrase that’s been recorded in a loop; it will be applied to
the recorded phrase. It will not be applied during recording
or overdubbing.
a
b