User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
13
Panels
a. Loop Effect selector
This selects the type of Loop Effect. The type of effect you
select here will be applied.
b. LOOP FX button
This turns the Loop Effect on/off.
The button will light-up green when the effect is on, and it
will blink while you’re editing the effect.
Note: Turning the effect selector will also pedal the Loop
Effect on.
4. Control pedal section
You can use this pedal to control the parameters of the Pre
Effect or Loop Effect, or to control the volume.
a. Pedal LED
This LED will be lit or unlit to
indicate the state of the function
that’s assigned to the control pedal.
) p.39 “Control pedal settings”
b. Control pedal
This pedal controls the effect
parameter that’s assigned to it, or
controls the volume.
For details on how to assign a
function to the pedal, please refer to
“Control pedal settings” on page 39.
For details on the effect parameters
a
b
that you can control, please refer to “About the Pre Effect
and Loop Effect” on page 29.
5. Metronome section
Here you can specify the metronome setting and time
signature.
a. METRONOME button
This button turns the metronome sound on/off.
When you press the button, it will blink, and
you’ll hear the metronome. The button will blink
in synchronization with the tempo that you
specified using the TRIGGER/TAP pedal.
To adjust the metronome volume, hold down
this button and turn the EDIT knob.
To set the time signature, hold down this button for
approximately two seconds and then turn the EDIT knob.
) p.20 “Using the metronome as a guide while you record”
a