User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
17
Connect your instrument and turn on the power
Connections
1.MakesurethattheDynamicLooper’sSTANDBYswitch
isintheSTANDBYposition.
2.UseacabletoconnecttheOUTPUTjacktoyourguitar
ampormixer.
Note: The Dynamic Looper’s output is monaural.
Do not connect headphones to the OUTPUT jack. Doing
so may damage your headphones.
3.UseaguitarcabletoconnectyourguitartotheINPUT
jack.Alternatively,useacabletoconnectyourmictothe
MICINjack.
Acoustic feedback might occur depending on where the
connected mic is located in relation to the amp that’s
connected to the OUTPUT jack. If feedback occurs, take
the following steps.
• Point the mic in a different direction.
• Move the mic away from the speaker.
• Adjust the rear panel MIC IN TRIM knob.
Acoustic feedback may also occur when you apply an
effect to the mic input. If so, take the same steps listed
above.
If the mic and amp are close together, the output sound of
the amp can be picked up by the mic. If you record or
overdub in this state, these sounds will also be recorded.
Make sure that the mic and amp are sufficiently separated
so that the sound from the amp is not picked up.
Turning the power on
1.Makesurethatthevolumeofyourampormixeris
sufficientlylowered,andthenturntheDynamic
Looper’sSTANDBYswitchtotheONposition.
The power will turn on, and the program/value display
will indicate the current program number.
2.Turnonthepoweroftheconnectedampormixer,and
raisethevolume.
3.Playyourguitar,andadjustitsvolumewithoutallowing
thePEAKLEDtolight-up.
4.Vocalizeintoyourmic,andadjusttherearpanelTRIM
knobwithoutallowingthePEAKLEDtolight-up.
Note: The Dynamic Looper contains an auto power-off
function. The power will automatically turn off
approximately four hours after the last user input
occurred ()p.41 “Auto Power-Off function”).
Turning the power off
1.Lowerthevolumeofyourampormixer.
2.SettheSTANDBYswitchtotheSTANDBYposition.