User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
23
Overdubbing a performance by playing along with a recorded phrase
Resample a phrase with the Loop Effect
applied
Please refer to “Resampling” on page 25.
Overdubbing a performance
by playing along with a
recorded phrase
Here we’ll explain how to overdub by playing along with
the phrase you recorded on Loop 1.
1.Selecttheprogramthatprovidesthesoundthatyou
want.Asdesired,youcanalsoadjusttheeffect
parameters.
) p.18 “Applying an effect to your guitar performance or
mic audio”
) p.37 “Editing a program”
2.PresstheSTOPpedalandPROGRAMUPpedal
simultaneously,makingtheLoop1currentloopLED
light-up.
3.PresstheREC/PLAY/OVERDUBpedaltoplaybackLoop
1.
4.Atthepointwhereyouwanttostartoverdubbing,press
theREC/PLAY/OVERDUBpedal,andplayyour
instrument.
The Loop 1 LOOP STATUS LED will light-up orange, and
overdubbing will begin.
Hint: If a parameter of the Pre Effect is assigned to the
control pedal (the pedal LED will be lit-up red), you can
use the pedal to control the Pre Effect while you overdub.
5.PressthePLAY/REC/OVERDUBpedalatthepoint
whereyouwanttostopoverdubbing.
The Loop 1 LOOP STATUS LED will light-up green, and the
Dynamic Looper will switch from overdubbing to playback.
6.PresstheSTOPpedaltostopLoop1playback.
Hint: The Dynamic Looper lets you specify what will
occur when you stop playback.
) p.25 “Specifying how the loop will stop”
Undoing overdubbing
If you want to cancel the last-performed overdub, proceed as
follows from the overdubbed state.
1.HolddownthePROGRAMUPpedal.
2.Whentheprogram/valuedisplayblinks“Und,”release
thePROGRAMUPpedal.
The last-performed overdub will be undone.